• 한국해안해양공학회지
• /
• 제12권4호
• /
• pp.168-180
• /
• 2000

In the Part I, the three dimensional model testing with NNW deep water wave direction gave the results such that the occurrence of breaking waves over the peak of Ear-Do caused very small wave height at the structure position. But the measured wave forces were rather greater than the calculated forces based on deep water wave height. Furthermore, It was also perceived that the time series of the forces looked like corresponding to the case that waves were superimposed by an unidirectional current. In the present Part II, the current is presumed to be a flow secondly induced by breaking waves, and an extensive study to clarify the current in a quantitative sense is performed through numerical analysis and hydraulic experiment. The results showed that a strong circulation can surely occur in the vicinity of the structure due to radiation stress differentials given by the breaking waves. It was also recognized that the velocity of the induced current varied with the magnitude of energy dissipation rate introduced in the numerical analysis. The numerical analysis was tuned adjusting the dissipation rate so that the calculated wave field could closely match with the experimental results of Part I. The fluid force (in prototype) for the optimal match showed approximately 2.2% increased over the calculated value based on the deep water wave height (24.6m) whereas the force corresponding to the average of the experimental values showed the increase of about 13.0%.

• 사회복지연구
• /
• 제37호
• /
• pp.171-197
• /
• 2008

본 연구는 국민기초생활보장법 하의 조건부 수급자가 자활직업훈련 프로그램의 참여로 인해 임금이 향상되었는지에 관해 실증적으로 분석 하였다. 분석 자료로는 한국노동연구원에서의 자활사업 참여자를 대상으로 한 '자활대상자 직업훈련 실태'조사와 한국보건사회연구원에서 실시하는 2004년 '자활패널'조사 자료를 결합하여 '자활직업훈련 실태'조사의 응답자를 실험그룹으로'자활패널'을 비교그룹으로 구성하여 분석하였으며, 기존 연구의 통계적 취약점을 극복하기 위해 Propensity Score Matching 방법을 이용하여 자활직업훈련의 임금효과를 분석하였다. 분석 결과 자활직업훈련 참가자들이 그와 비슷한 특성을 가진 비교그룹에 비해서 약 12만원 정도 소득이 낮음을 확인함으로써, 이러한 부정적인 효과가 나타난 원인과 의미에 대해서 논의하였다.

• 반도체디스플레이기술학회지
• /
• 제21권3호
• /
• pp.101-104
• /
• 2022

Mist-CVD is known to have advantages of low cost and high productivity compared to ALD and PECVD methods. It is capable of reacting to the substrate by misting an aqueous solution using ultrasonic waves under vacuum-free conditions of atmospheric pressure. In particular, Ga₂O₃ is regarded as advanced power semiconductor material because of its high quality of transmittance, and excellent electrical conductivity through N-type doping. In this study, Computational Fluid Dynamics were used to predict the uniformity of the thin film on a large-area substrate. And also the deposition pattern and uniformity were analyzed using the flow velocity and particle tracking method. The uniformity was confirmed by quantifying the deposition cross section with an FIB-SEM, and the consistency of the uniformity prediction was secured through the analysis of the CFD distribution. With the analysis and experimental results, the match rate of deposition area was 80.14% and the match rate of deposition thickness was 55.32%. As the experimental and analysis results were consistent, it was confirmed that it is possible to predict the deposition thickness uniformity of Mist-CVD.

• 국제초고층학회논문집
• /
• 제1권1호
• /
• pp.53-59
• /
• 2012

With the rise in CPU power and the generalization and popularity of computers, engineering practice also changed from hand calculations to 3D computer models, from elastic linear analysis to 3D nonlinear static analysis and 3D nonlinear transient dynamic analysis. Thanks to holistic design approach and current trends in freeform and contemporary architecture, BIM concept is no longer a dream but also a reality. BIM is not just providing a media for better co-ordination but also to shorten the round-the-clock time in updating models to match with other professional disciplines. With the parametric modeling tools, structural information is also linked with BIM system and quickly produces analysis and design results from checking to fabrication. This paper presents a new framework which not just linked the BIM system by means of parametric mean but also create and produce connection FE model and fabrication drawings etc. This framework will facilitate structural engineers to produce well co-ordinate, optimized and safe structures.

• 동력기계공학회지
• /
• 제19권6호
• /
• pp.54-59
• /
• 2015

This paper is a numerical study on the correlation of leakage by the variation of operating temperature and orifice diameter applying to hydrostatic bearing in hydraulic actuator. Compared with Brackbill and Kandlikar experimental paper to verify the validity of the numerical analysis technique of the present study, we derive the result that the results of experiments and numerical analysis to match very well. CFD analysis program were analyzed using a commercial code FLUENT V14.5. Inlet and outlet, were applied pressure conditions, the main variables of the analysis is temperature and the orifice inner diameter. The analysis results, pressure value has decreased as the oil temperature and the orifice diameter increases.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2006년도 춘계학술대회 논문집
• /
• pp.357-358
• /
• 2006

Importance of using an injection molding analysis has been increased. However the application of it has not been increased because the results of analysis do not sometime match to practical molding. Therefore, the difference of flow analysis and practical molding should be decreased. This study presents reasons of the difference for the location of weld-line in the flow analysis and practical molding on automobile bumper molding.

• 한국원자력학회:학술대회논문집
• /
• 한국원자력학회 1997년도 춘계학술발표회논문집(1)
• /
• pp.57-61
• /
• 1997

A Canadian Deuterium Uranium (CANDU) reactor core calculation was performed using lattice parameters generated by HELIOS. The HELIOS-based lattice parameters were processed by TABGEN in a form suitable for the core analysis code RFSP. The core calculation was performed and the results were compared to those of the reference calculation which uses POWDERPUFS-V (PPV) for the lattice parameter generation. The characteristics of the core calculated based on the PPV and HELIOS lattice parameters match within 0.4%$\Delta$k and 7% for the excess reactivity and the channel power distribution, respectively.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 1998년도 하계종합학술대회논문집
• /
• pp.145-148
• /
• 1998

In this paper, a microstrip antenna is designed using a rectangular patch. To find characteristics of the antenna, computer simulations of the rectangular single microstrip patch antenna are performed with changing width. And we compared the result of computer simulation with the experimental value. Through the results, we found that the 3-D FDTD method is an effective method for designing microstrip patch antenna. According to simulation the resonant point has been found it in the frequency received from GPS satellite. It is thought that make it match by adjusting the feedpoint.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2001년도 ICCAS
• /
• pp.129.1-129
• /
• 2001

In this paper, we present an approach for matching images from finding interesting points and applying new image interpolation algorithm. New algorithms are developed that automatically align the input images match them and reconstruct 3-D surfaces. The interpolation algorithm is designed to cope with simple shapes. The proposed image interpolation algorithm generate a rotation image about vertical axes by an any angle from 4 base images. Each base image that was obtained from CCD camera has an angle difference of 90$^{\circ}$ The proposed image interpolation algorithm use the geometric analysis of image and depth information.

• 유체기계공업학회:학술대회논문집
• /
• 유체기계공업학회 1999년도 유체기계 연구개발 발표회 논문집
• /
• pp.61-68
• /
• 1999

We have measured pressure distributions within the diffuser and pressures at the inlet and outlet of the compressor in orde to match impeller and low-solidity diffuser of 500RT centrifugal refrigerant-compressor which has been developed in LG Cable Ltd. Modified Stanitz equation is used to predict the measured data by tuning several parameters and then is validated. Using the validated parameters and modified Stanitz equation, we have obtained data necessary to design the diffuser.