• Journal of the Korean Society for Precision Engineering
• /
• v.15 no.5
• /
• pp.153-160
• /
• 1998

A master-slave system for tele-operation had been developed and tested for several decades. In this paper the master robot is composed of several wires and provides position information of the handle which is driven by a operator within the master robot work space. A PC is used for the command calculation for a slave robot. This paper deals with the relation between the number of strings and D.O.F of the master robot, control method of the slave robot during the operation and the monitoring method over the working area by the computer graphics simulation. The D.O.F of the master robot can be modified by adding or subtracting some strings. The controller of the slave robot uses the advanced PD control method to keep the performance against varying working load.

• 제어로봇시스템학회:학술대회논문집
• /
• 1996.10b
• /
• pp.168-172
• /
• 1996

In master-slave teleoperating system, it is important that the system has good maneuverability. In this paper, it is addressed an adaptive learning control method applicable to the master-slave system. This control scheme has the ability to estimate uncertain dynamic parameters included intrinsically in the system and to achieve the desired performance without the nasty matrix operation. The proposed method is applied to a master-slave teleoperating system composed of two SCARA robots and verified experimentally.

• Proceedings of the KIPE Conference
• /
• 2016.07a
• /
• pp.479-480
• /
• 2016

This paper introduces a master and slave control algorithm for parallel operation of UPS system. If each module of UPS system control the output voltage and filter inductor current in parallel operation, it occur unbalanced output power each module. To operate UPS system parallel, it need a algorithm that control output power of modules. A master and slave control algorithm is helpful to balance output power of modules by controlling output current. The effect of a master and slave control algorithm is proved by simulations.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.58 no.1
• /
• pp.199-202
• /
• 2009

Scan design is currently the most widely used structured Design For Testability approach. In scan design, all storage elements are replaced with scan cells, which are then configured as one or more shift registers(also called scan chains) during the shift operation. As a result, all inputs to the combinational logic, including those driven by scan cells, can be controlled and all outputs from the combinational logic, including those driving scan cells, can be observed. The scan inserted design, called scan design, is operated in three modes: normal mode, shift mode, and capture mode. Circuit operations with associated clock cycles conducted in these three modes are referred to as normal operation, shift operation, and capture operation, respectively. In spite of these, scan design methodology has defects. They are power dissipation problem and test time during test application. We propose a new methodology about scan shift clock operation and present low power scan design and short test time.

• Proceedings of the KIEE Conference
• /
• 2006.10d
• /
• pp.218-221
• /
• 2006

This paper reports on a Realtime OS based motor control system for laparoscopic surgery robot which enables telesurgery and overcomes shortcomings with conventional laparoscopic surgery. The system has a conventional master-slave robot configuration and the control system consists of joint controllers, host controllers, and power units. The robot features (1) a compact slave robot with 5 DOF (Degree Of Freedom) expanding the workspace of each tool and increasing the number of tools operating simultaneously, and (2) direct 1:1 correspondence in the joint of master and slave robot that simplifies control algorithm and enhances reliability. Each master, slave and GUI (Graphical User Interface) host has a dedicated RTOS (RealTime OS), RTLinux-Pro (FSMLabs Inc., U.S.A.) Each master and slave controller set pair has a dedicated CAN (Controller Area Network) channel for control and monitoring signal communication. Total 4 pairs of the master/slave manipulators as current are monitored by one host controller for operation monitoring and higher level motion control. The system showed acceptable performance in both position control precision and master-slave motion synchronization and is now under further development for better safety and control fidelity for clinically applicable prototype.

• 제어로봇시스템학회:학술대회논문집
• /
• 1998.10a
• /
• pp.386-390
• /
• 1998

A master-slave system is proposed as a teaching device for a dual arm robot. The slave robots are remotely controlled by two delta-type master arms. In order to help the operator to observe the target object from the desired position and desired direction, cameras are mounted on a specialized manipulator, Movements of two slave arms are coordinated with that of the cameras. Due to this coordinated movements, the operator needs not to care the geometrical relation between the cameras and the slave robots.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2003.06a
• /
• pp.1101-1104
• /
• 2003

In this paper, we performed the study on the operation characteristics of tele-grasping using the developed experimental system. The experimental system consists of master and slave gripper. and signal processing system. For the stable grasping of an object, this system feedback the normal force obtained from the straingage of the slave gripper to magnetic particle brake of the master gripper through the signal processing system. This experimental system can control the grasping force in remote using the force feedback device. Some experimental results of the-tele-grasping are presented and discussed

• International Journal of Fuzzy Logic and Intelligent Systems
• /
• v.3 no.2
• /
• pp.161-165
• /
• 2003

In this paper, we investigate the issues on the design and implementation of tele-operation system based on the haptic interface. Here, the 3-DOF haptic device and the X-Y-Z stage are employed as master controller and slave system respectively. For this master-slave system, the force feedback algorithm, the modeling of virtual environments and the control method of X-Y-Z stage are presented. In this paper, internet network is used for data communication between master and slave. We construct virtual environment of the real convex surface from the force-feedback in controlling the X-Y-Z stage and measuring the force applied by the 3-DOF haptic device.

• 제어로봇시스템학회:학술대회논문집
• /
• 2001.10a
• /
• pp.140.4-140
• /
• 2001

This paper presents the duplex controller operated as master slave for Self Excited Static Type excitation system and the results of operation for duplex digital excitation system. Software is made up duplex multi-tasking control algorithm which is based on VxWorks(real-time OS), preprocessing algorithm for input-output signal, BSP & Device Driver for interfacing hardware and software, and OIS(Operator Interface Station) program, HMI S/W. Master controller and slave controller intercommunicate dominant data to minimize bump when controller switchover from master to slave occurs. Communication between master controller and slave controller is duplicated and communication between OIS and controller is duplicated. Hardware is made up VMEBUS based controller which is designed with PPC & I/O board ...

• Proceedings of the Korean Institute of Intelligent Systems Conference
• /
• 2003.09a
• /
• pp.236-239
• /
• 2003

In this paper, we investigate the issues for the design and implementation of tele-operation system based on the haptic interface. Here, the 3-DOF haptic device and the x-y-z stage are employed as master controller and slave system respectively. In this master-slave system, the force feedback algorithm, the modeling of virtual environments and the control method of x-y-z stage are proposed. In this paper, inernet network is used for data communication between master and slave. We construct virtual environment of the real convex surface from the force-feedback in controlling the X-Y-Z stage and getting the force applied by the 3-DOF haptic device.