• Proceedings of the Korea Concrete Institute Conference
• /
• 2005.11a
• /
• pp.351-354
• /
• 2005

Quality of concrete required to achieve the desired levels of strength and durability depend on the effectiveness of the curing method. During cold weather, the concrete at the time of placement should be taken to prevent damage to concrete due to freezing. Since the cement-water reaction is exothermic by nature, the temperature within mass concrete can be quite high. The temperature control for massive sections should be taken more careful than for shallow sections. However, in the constructing hydraulic structures, the curing temperature control for concrete had been very difficult to be taken in a proper way because the conditions constructing them are poor and contractors are small enterprises. For several. reasons including above, Rural Research Institute has developed a device and program for recording curing temperature history in cold weather concrete and mass. As there are two major advantages of the device, namely cheapness and availability, this program and device has been recommended to the use of curing temperature control in cold weather concrete and mass.

• Computers and Concrete
• /
• v.15 no.4
• /
• pp.485-501
• /
• 2015

Cooling by the flow of water through an embedded cooling pipe has become a common and effective artificial thermal control measure for massive concrete structures. However, an extreme thermal gradient induces significant thermal stress, resulting in thermal cracking. Using a mesoscopic finite-element (FE) mesh, three-phase composites of concrete namely aggregate, mortar matrix and interfacial transition zone (ITZ) are modeled. An equivalent probabilistic model is presented for failure study of concrete by assuming that the material properties conform to the Weibull distribution law. Meanwhile, the correlation coefficient introduced by the statistical method is incorporated into the Weibull distribution formula. Subsequently, a series of numerical analyses are used for investigating the influence of the correlation coefficient on tensile strength and the failure process of concrete based on the equivalent probabilistic model. Finally, as an engineering application, damage and failure behavior of concrete cracks induced by a water-cooling pipe are analyzed in-depth by the presented model. Results show that the random distribution of concrete mechanical parameters and the temperature gradient near water-cooling pipe have a significant influence on the pattern and failure progress of temperature-induced micro-cracking in concrete.

• International Journal of Concrete Structures and Materials
• /
• v.4 no.2
• /
• pp.97-104
• /
• 2010

The crushed limestone sand is an abundant material in Tunisia, which induces many environmental problems. Indeed, available stocks of siliceous sand drastically decrease because of its massive use in hydraulic concrete. Some recent research works, carried out in Tunisia, concluded that crushed limestone sand may be used in concrete manufacture instead of siliceous sand traditionally used. In this context, an experimental study was achieved in order to quantify the influence of a partial or total substitution of siliceous sand by crushed limestone sand on hydraulic concrete performances. Preliminary chemical and physical tests on crushed sand indicated that it presented the minimum requirement for its use as aggregate in hydraulic concrete. 79 concretes were then prepared with siliceous sand, crushed limestone sand and a mix of the two sands. Their slump value and compressive strengths were measured on plain concretes. Complementary structural tests on reinforced concrete beam were also performed. The results proved that crushed limestone sand concretes showed workability and mechanical performances closed to those of siliceous sand concretes.

• Journal of the Korea Concrete Institute
• /
• v.20 no.5
• /
• pp.661-668
• /
• 2008

It is necessary to develop a new technology for effectively reducing hydration heat and controlling thermal cracking caused increasing construction of large size massive concrete structures such as mat foundation of high-rise building, grandiose bridge, and LNG tank. Therefor, to develop a new technology for reducing hydration heat of large size massive concrete in this study, after developing the latent heat binder for controling hydration heat of concrete by application of latent heat material, it was investigated basic properties and durability such as slump, air content and compressive strength, shrinkage properties, permeability, freezing and thawing resistance, corrosion, and hydration heat generation properties of concrete using latent heat binder. As a test result, it was confirmed that latent heat binder was not affected adversely the basic property and durability of concrete, and was advanced on the reduction of hydration heat and control of thermal crack. It is expected to be applied as the excellent technology on the management of hydration heat and thermal crack in large size mass concrete structures.

• Magazine of the Korea Concrete Institute
• /
• v.4 no.3
• /
• pp.101-111
• /
• 1992

매스콘크리트 구조물에서의 시멘트 수화열은 구조물의 균열을 발생시킬 만큼 큰 내부온도를 발생시킨다. 따라서 매스콘크리트 구조물에서의 설계와 시공단계에서 내부온도응력을 예측할 수 있다면 이와같은 균열로 인한 구조물의 피해를 예방할 수 있을 것이다. 그리고 수화열에 의한 온도증가는 타설초기에 발생하므로 크리이프에 의한 영향도 매우크다. 따라서 온도응력해석시 크리이프와 건조수축의 영향을 고려하는 것이 구조물의 안전성과 사용성을 정확히 파악하는데 필요하다. 본 연구는 먼저 매스콘크리트의 온도이력을 유한요소법에 의해 해석하고, 작용하중이나 온도이력을 크리이프와 건조수축영향을 고려하여 콘크리트 구조물의 응력과 변형을 유한요소법에 의해 계산하였다. 본 연구에서 온도이력 계산과 콘크리트구조물의 응력과 변형의 계산을 위해 작성한 프로그램 결과를 실제 구조물의 실험결과와 비교하였을 때 양호한 결과를 얻었다.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2006.05b
• /
• pp.445-448
• /
• 2006

In order to control the temperature crack of massive dam concrete, the selection of appropriate materials like binder, aggregates etc., is essential. To select the optimal mix proportion, ordinary portland cement(Type I) plus 25% of fly ash and low heat portland cement(Type IV) are used as binder, and 80mm of coarse aggregates are used to reduce the amount of binder and compare the compressive strength, hydration temperature and crack index. The results of this study are as following. 1. The strength of Type IV cement is advantageous on the long-term age. 2. According to the temperature measured on mock-up$(1.5m{\times}1.5m{\times}1.5m)$, and realized the thermal analysis, the Type IV cement carried out advantageous to control the thermal crack.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2009.05a
• /
• pp.263-264
• /
• 2009

This paper presents the example of corrosion monitoring sensor that is applied to massive RC structure exposed to marine environments. Corrosion monitoring sensor is used as an early warning system to predict the initial stage of corrosion in concrete structures. So, it can be a good method to verify the design life and prepare measures for concrete deterioration in advance.

• Computers and Concrete
• /
• v.1 no.3
• /
• pp.249-260
• /
• 2004

The stress transmission mechanism in pretensioned concrete beams, though very interesting from an economical point of view, is very complex, integrating various phenomenons such as sliding, bond, bursting. For long the complexity of this mechanism has led engineers to provide a massive rectangular anchorage zone at each end of the beam. The necessity of using such a concrete reinforcement is certainly unquestionable in post-tensioned beams. However in pretensioned elements the stresses induced in concrete in the anchorage zone are smaller than in post-tensioned elements. In this article the stress field in the end zone is calculated numerically and from this analysis the possible reduction of the cross-section of the anchorage block is examined.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1998.10b
• /
• pp.922-927
• /
• 1998

Pipe cooling has been popularly used in the mass concreting work to reduce temperature of the structure since it is known to be the easiest way to apply and has been the customary usage. But wrong application of the system results in the harmful effect on the structure by crack formation due to thermal shocks and improper cooling schemes. Thus, this study aims at the suppling of effective cooling methods through parametric study. For this, circulating method, velocity of water supply and circulating duration were selected as critical factors affecting the effectiveness of cooling system. As a results of thermal analysis, it was found that too much thermal gradient in the vicinity of the pipe creates localized radial or circumferential cracks. The duration of circulating cooling may be recommended to be as short as several days which may safely reduce the concrete temperature to below a final stable value. It was also found that pipe cooling is more effective to decrease the degree external restraints than internal one.

• Computers and Concrete
• /
• v.12 no.1
• /
• pp.53-64
• /
• 2013

The curing temperature is known to influence the rate of mechanical properties development of early age concrete. In realistic sites the temperature of concrete is not isothermal $20^{\circ}C$, so the paper measured adiabatic temperature increases of four different concretes to understand heat emission during hydration at early age. The temperature-matching curing schedule in accordance with adiabatic temperature increase is adopted to simulate the situation in real massive concrete. The specimens under temperature-matching curing are subjected to realistic temperature for first few days as well as adiabatic condition. The mechanical properties including compressive strength, splitting strength and modulus of elasticity of concretes cured under both temperature-matching curing and isothermal $20^{\circ}C$ curing are investigated. The results denote that comparing temperature-matching curing with isothermal $20^{\circ}C$ curing, the early age concretes mechanical properties are obviously improved, but the later mechanical properties of concretes with pure Portland and containing silica fume are decreased a little and still increased for concretes containing fly ash and slag. On this basement using an equivalent age approach evaluates mechanical properties of early age concrete in real structures, the model parameters are defined by the compressive strength test, and can predict the compressive strength, splitting strength and elasticity modulus through measuring or calculating by finite element method the concreted temperature at early age, and the method is valid, which is applied in a concrete wall for evaluation of crack risking.