• KSBB Journal
• /
• v.4 no.2
• /
• pp.118-122
• /
• 1989

From the on-line mass spectrometric analyese of the exhaust gaseous composition of fermentor and the material balance equations for oxygen and carbon dioxide, oxygen uptake rate (OUR) and carbon dioxide evolution rate (CER) were calculate using a personal computer (IBM PC-AT) interfaced to a quadrupole mass spectromter. The calculate OUR and CER were used for the indirect estimation of cell and substrate concentrations during the batch culture of Candida utilis. For the estimation of sustrate concentration, the yield model of Pirt was applied. It was found that the cell and substrate (glucose) concentration could be ssatisfactorily estimataed and the results showed the more accurate estimations of both fermentation state variables when OUR data were used than CER data.

• Journal of the Korean Physical Society
• /
• v.80
• /
• pp.953-963
• /
• 2022

Post-neutron emission fission product mass distributions are calculated by using pre-neutron emission fission product yields (FPYs) and neutron multiplicity. A semi-empirical model is used to calculate the pre-neutron FPY, first. Then the neutron multiplicity for each fission fragment mass is used to convert the pre-neutron FPY to the post-neutron FPY. In doing so, assumptions are made for the probability for a pre-emission fission fragment with a mass number A^* to decay to a post-emission fragment with a mass number A. The resulting post-neutron FPYs are compared with the data available. The systems where the experimental data of not only the pre- and post-neutron FPY but also neutron multiplicity are available are the thermal neutron-induced fission of ²³³U, ²³⁵U and ²³⁹Pu. Thus, we applied the model calculations to these systems and compared the calculation results with those from the GEF and the data from the ENDF and the EXFOR libraries. Both the pre- and post-neutron fission product mass distributions calculated by using the semi-empirical model and the neutron multiplicity reproduce the overall features of the experimental data.

• Macromolecular Research
• /
• v.9 no.5
• /
• pp.253-258
• /
• 2001

Crosslinked poly(ethylene glycol)s (PEGs) were prepared by ultraviolet irradiation of low molar mass, liquid PEGs in the presence of benzophenone (BP) as a photoinitiator. The networks obtained have been characterized by DSC, IR, and contact angle measurements, and their water absorption and equilibrium swelling have been examined. The percent of gel formed and degree of swelling of the networks in water were dependent on the amount of BP in the reaction mixture, irradiation time and molar mass of PEG. Gel fraction yield exceeded 84%, and equilibrium swelling in water varied from 49 to 244%.

• Proceedings of the Korea Technical Association of the Pulp and Paper Industry Conference
• /
• 2006.06b
• /
• pp.291-294
• /
• 2006

Studies of the effectiveness of anthraquinone (AQ) in kraft-AQ pulping in terms of its mechanism of mass transfer have been conducted. Experiments performed have demonstrated an 'apparent solubility' of AQ in caustic solutions of wood lignin. The adsorption behavior of AQ species was also analyzed. Anthraquinone-2-sulfonic acid (AQ-S), a water-soluble derivative of AQ, showed selective adsorption on wood. A mechanism for the transport of AQ into wood chips during kraft pulping are proposed, and some explanations for previously unexplained observations are addressed.

• Mass Spectrometry Letters
• /
• v.14 no.1
• /
• pp.1-8
• /
• 2023

Eutylone, dibutylone, and dimethylone are potential psychotropic designer drugs. The purpose of this study was to investigate the in vitro metabolic pathways of synthetic cathinones with methylenedioxy groups. The three methylenedioxy derivatives were incubated with human liver microsomes. The metabolites were characterized based on liquid chromatography and quadrupole-time-of-flight mass spectrometry. Eutylone, dibutylone, and dimethylone were metabolized to yield three, six, and four metabolites, respectively. Reduction and demethylenation were the major metabolic pathways for all three drugs tested. However, dibutylone and dimethylone showed an additional metabolite generated via N-oxidation. These results provide evidence for the in vivo metabolism of methylenedioxy synthetic cathinones, and could be applied to the analysis of synthetic cathinones and their relevant metabolites in biological samples.

• Journal of Korean Society of Environmental Engineers
• /
• v.32 no.8
• /
• pp.747-753
• /
• 2010

This study was performed to investigate the removal characteristics of volatile organic compounds (VOCs) in the gasphase biofilters, and to propose a stoichiometric analysis approach to characterize biological reaction through carbon mass balance. The VOCs studied were toluene, styrene, methyl ethyl ketone (MEK), and methyl isobutyl ketone (MIBK) as a single substrate for each biofilter. The critical loading rate was determined to be $46.9\;g/m^3{\cdot}hr$, $25.8\;g/m^3{\cdot}hr$, $96.3\;g/m^3{\cdot}hr$, and $66.5\;g/m^3{\cdot}hr$ for toluene, styrene, MEK, and MIBK, respectively. The obtained results indicated that the critical loading rate was well correlated the octanol-water partition coefficient. In the analysis of carbon mass balance, carbon recovery to $CO_2$ became relatively lower as substrate loadings increased, but higher for carbon recovery to biomass. Stoichiometric analysis revealed that biomass yield increased as substrate loadings increased, and its coefficient (g biomass/g substrate) varied from 0.31 to 0.57 for toluene, 0.29 to 0.57 for styrene, 0.08 to 0.56 for MEK, and 0.14 to 0.53 for MIBK.

• Environmental Engineering Research
• /
• v.22 no.1
• /
• pp.19-30
• /
• 2017

Direct catalysis of vapors from vacuum pyrolysis of biomass was performed on MCM-41 to investigate the effects of operating parameters including catalyzing temperature, catalyzing bed height and system pressure on the organic yields. Optimization of organic phase yield was further conducted by employing response surface methodology. The statistical analysis showed that operating parameters have significant effects on the organic phase yield. The organic phase yield first increases and then decreases as catalyzing temperature and catalyzing bed height increase, and decreases as system pressure increases. The optimal conditions for the maximum organic phase yield were obtained at catalyzing temperature of $502.7^{\circ}C$, catalyzing bed height of 2.74 cm and system pressure of 6.83 kPa, the organic phase yield amounts to 15.84% which is quite close to the predicted value 16.19%. The H/C, O/C molar ratios (dry basis), density, pH value, kinematic viscosity and high heat value of the organic phase obtained at optimal conditions were 1.287, 0.174, $0.98g/cm^3$, 5.12, $5.87mm^2/s$ and 33.08 MJ/kg, respectively. Organic product compositions were examined using gas chromatography/mass spectrometry and the analysis showed that the content of oxygenated aromatics in organic phase had decreased and hydrocarbons had increased, and the hydrocarbons in organic phase were mainly aliphatic hydrocarbons. Besides, thermo-gravimetric analysis of the MCM-41 zeolite was conducted within air atmosphere and the results showed that when the catalyst continuously works over 100 min, the index of physicochemical properties of bio-oil decreases gradually from 1.15 to 0.45, suggesting that the refined bio-oil significantly deteriorates. Meanwhile, the coke deposition of catalyst increases from 4.97% to 14.81%, which suggests that the catalytic activity significantly decreases till the catalyst completely looses its activity.

• Korean Journal of Materials Research
• /
• v.26 no.7
• /
• pp.370-375
• /
• 2016

Tensile tests and creep tests were carried out at high temperatures on an Al-$Al_4C_3$ alloy prepared by mechanical alloying technique. The material contains about 2.0% carbon and 0.9% oxygen in mass percent, and the volume fractions of $Al_4C_3$ and $Al_2O_3$ particles are estimated at 7.4 and 1.4%, respectively, from the chemical composition. Minimum creep rate decreased steeply near two critical stresses, ${\sigma}_{cl}$ (the lower critical stress) and ${\sigma}_{cu}$ (the upper critical stress), with decreasing applied stress at temperatures below 723 K. Instantaneous plastic strain was observed in creep tests above a critical stress, ${\sigma}_{ci}$, at each test temperature. ${\sigma}_{cu}$ and ${\sigma}_{ci}$ were fairly close to the 0.2% proof stress obtained by tensile tests at each test temperature. It is thought that ${\sigma}_{cl}$ and ${\sigma}_{cu}$ correspond to the microscopic yield stress and the macroscopic yield stress, respectively. The lower critical stress corresponds to the local yield stress needed for dislocations to move in the soft region within subgrains. The creep strain in the low stress range below 723 K arises mainly from the local deformation of the soft region. The upper critical stress is equivalent to the macroscopic yield stress necessary for dislocations within subgrains or in subboundaries; this stress can extensively move beyond subboundaries under a stress above the critical point to yield a macroscopic deformation. At higher temperatures above 773 K, the influence of the diffusional creep increases and the stress exponent of the creep rate decreases.

• Journal of Microbiology and Biotechnology
• /
• v.17 no.6
• /
• pp.952-959
• /
• 2007

His-His-Leu (HHL), a tripeptide derived from a Korean soybean paste, is an angiotensin-I-converting enzyme (ACE) inhibitor. We report here a method of producing this tripeptide efficiently by expressing tandem multimers of the codons encoding the peptide in E. coli and purifying the HHL after hydrolysis of the peptide multimers. The HHL gene, tandemly multimerized to a 40-mer, was ligated with ubiquitin as a fusion gene (UH40). UH40 was inserted into vector pET29b; the UH40 fusion protein was then produced in E. coli BL21. The recombinant UH40 protein was purified by cation-exchange chromatography with a yield of 17.3mg/l and analyzed by matrixassisted laser desorption ionization (MALDI) time-of-flight (TOF) mass spectrometry and protein N-terminal sequencing. Leucine aminopeptidase was used to cleave a 405-Da HHL monomer from the UH40 fusion protein and the peptide was purified using reverse-phase high-performance liquid chromatography (HPLC) on a C18 HPLC column, with a final yield of 6.2mg/l. The resulting peptide was confirmed to be HHL with the aid of MALDI-TOF mass spectrometry, glutamine-TOF mass spectrometry, N-terminal sequencing, and measurement of ACE inhibiting activity. These results suggest that our production method is useful for obtaining a large quantity of recombinant HHL for functional antihypertensive peptide studies.

• Parasites, Hosts and Diseases
• /
• v.35 no.3
• /
• pp.149-154
• /
• 1997

A storage mite, Tyrophcgus putrescentiae, is recently known to be widely distributed in Korea, being commonly found in house dust, and may, therefore, be allergenically important. The purpose of this study was to develop mass rearing techniques for supplying a large quantity of allergens. The laboratory mouse food powder gave the highest yield, showing 1,251.5-fold increase in number after 10 weeks, and the mixed powder of laboratory mouse food and yeast (1 : 1) also gave same level of the production (1.203 1-fold increase in week 10). Several different combinations of temperature and relative humidity conditions were compared, and the maximum propagation was obtained at $25^{\circ}C$ and 64% RH, showing 960-fold increase in number. When the same amount of culture media was used the size of the culture container did not significantly influence the quantitative yield of T. putrescentice mites.