• Earthquakes and Structures
• /
• v.15 no.5
• /
• pp.555-564
• /
• 2018

Allowing structures to uplift in earthquakes can significantly reduce or even avoid the development of plastic hinges within the structure. The permanent deformations in the structure can thus be minimized. However, uplift of footings can cause additional horizontal movements of a structure. With an increase in movement relative to adjacent structures, the probability of pounding between structures increases. This experimental study reveals that the footing mass can be used to control the vertical displacement of footing and thus reduce the horizontal displacements of an upliftable structure. A four storey model structure with plastic hinges and uplift capability was considered. Shake table tests using ten different earthquake records were conducted. Three different footing masses were considered. It is found that the amplitude of footing uplift can be greatly reduced by increasing the mass of the footing. As a result, allowing structural uplift does not necessary increase the horizontal displacement of the structure. The results show that with increasing footing weight, the interaction between structural and footing response can increase the contribution of the higher modes to the structural response. Consequently, the induced vibrations on secondary structure increase.

• Geomechanics and Engineering
• /
• v.15 no.3
• /
• pp.841-849
• /
• 2018

The purpose of a rock bolt is to improve the mechanical performance of a jointed-rock mass. The performance of a rock bolt is generally evaluated by conducting a field pullout test, as the analytical or numerical evaluation of the rock bolt behavior still remains difficult. In this study, wide range of field test was performed to investigate the pullout resistance of rock bolts considering influencing factors such as the rock type, water bearing conditions, rock bolt type and length. The test results showed that the fully grouted rock bolt (FGR) in water-bearing rocks can be inadequate to provide the required pullout resistance, meanwhile the inflated steel tube rock bolt (ISR) satisfied required pullout resistance, even immediately after installation in water-bearing conditions. The ISR was particularly effective when the water inflow into a drill hole is greater than 1.0 l/min. The effect of the rock bolt failure on the tunnel stability was investigated through numerical analysis. The results show that the contribution of the rock bolt to the overall stability of the tunnel was not significant. However, it is found that the rock bolt can effectively reinforce the jointed-rock mass and reduce the possibility of local collapses of rocks, thus the importance of the rock bolt should not be overlooked, regardless of the overall stability.

• Proceedings of the Korean Society of Soil and Groundwater Environment Conference
• /
• 2004.09a
• /
• pp.334-337
• /
• 2004

Groundwater chemistry in Namwon area, Korea, was investigated to understand the contribution of geochemical processes on groundwater chemistry. For this study, a total of 279 groundwater samples were collected from 93 wells distributed over the study area. Higher concentrations of major ions are generally encountered in the shallow alluvial wells, suggesting that these chemicals are originated from the surface contamination sources. Mass balance analysis based on reaction stoichiometry reveals that the water chemistry is regulated by three major chemical processes: weathering of silicate/ carbonate minerals, input of C1/SO$_4$ salts, and nitrate generating processes. The results show that mineral weathering is the most dominating factor regulating the groundwater chemistry. However, the groundwaters with the higher salt concentration indicate the larger mineral weathering effect, suggesting that some part of the mineral weathering effect is also associated with the anthropogenic activities such as limes applied to the cultivated lands, carbonates (CaCO$_3$) in the cement materials.

• Journal of architectural history
• /
• v.1 no.2 s.2
• /
• pp.116-136
• /
• 1992

Architectural essence of John Ruskin's discourse can resolve itself into natural beauty, craftmanship, and truth in structure, surface, and process. His theories became disciplines of modern English school, Art and Craft and Free architecture, in aspects of organic architecture, morality, and rationality. These concepts disseminated continental Art Nouveau and also became it's basic principles. But his empirical theories hated use of machine, and should find a ideal model in medieval romanticism of Gothic. Anti-machine, as a instictive guideline of English modern architecture, couldn't cope with the industrialization of 20th century, and Gothic revival interfered with creating a new style. Muthesius' discourses were taught by the power of group movements and modern concept of form in English school, originally by Ruskin. But he accepted the potentiality of machine and mass production, and stressed creating the new German style suitable with machine. With the progress of Deutscher Werkbund, his theories were advanced to 'quality' connected with craftmanship, to discourse on mechanical 'form', and lastly to 'standardization and type' for mass production. Mechanical functionalism of Muthesius and DWB were sophiscated and handed down to Bauhaus, and then finally helped establishment of the Modern Architecture and Internationalism. Both English and German modern architecture owed their contribution as well as limitation to Ruskin and Muthesius as theorists. Through this comparative study, we can see the priority of theory to practice, the theoretical justification based on insight for its society and future, and the practical character of theory itself.

• Journal of Mechanical Science and Technology
• /
• v.18 no.3
• /
• pp.513-525
• /
• 2004

This paper reports an experimental study on flow boiling of pure refrigerants R l34a and R l23 and their mixtures in a uniformly heated horizontal tube. The flow pattern was observed through tubular sight glasses with an internal diameter of 10㎜ located at the inlet and outlet of the test section. Tests were run at a pressure of 0.6 MPa in the heat flux ranges of 5-50㎾/㎡, vapor quality 0-100 percent and mass velocity of 150-600㎏/㎡s. Both in the nucleate boiling-dominant region at low quality and in the two-phase convective evaporation region at higher quality where nucleation is supposed to be fully suppressed, the heat transfer coefficient for the mixture was lower than that for an equivalent pure component with the same physical properties as the mixture. The reduction of the heat transfer coefficient in mixture is explained by such mechanisms as mass transfer resistance and non-linear variation in physical properties etc. In this study, the contribution of convective evaporation, which is obtained for pure refrigerants under the suppression of nucleate boiling, is multiplied by the composition factor by Singal et al. (1984). On the basis of Chen's superposition model, a new correlation is presented for heat transfer coefficients of mixture.

• Advances in aircraft and spacecraft science
• /
• v.7 no.1
• /
• pp.79-90
• /
• 2020

The dynamic coupling between shaker and test-article has been investigated by recent research through the so called Virtual Shaker Testing (VST) approach. Basically a VST model includes the mathematical models of the test-item, of the shaker body, of the seismic mass and the facility vibration control algorithm. The subsequent coupled dynamic simulation even if more complex than the classical hard-mounted sine test-prediction, is a closer representation of the reality and is expected to be more accurate. One of the most remarkable benefits of VST is the accurate quantification of the frequency down-shift (with respect to the hard-mounted value), typically affecting the first lateral resonance of heavy test-items, like medium or large size Spacecraft (S/Cs), once mounted on the shaker. In this work, starting from previous successful VST experiences, the parameters having impact on the frequency shift are identified and discussed one by one. A simplified analytical system is thus defined to propose an efficient and effective way of calculating the lower bound frequency shift through a simple equation. Such equation can be useful to correct the S/C lateral natural frequency measured during the test, in order to remove the contribution attributable to the shaker in use. The so-corrected frequency value becomes relevant when verifying the compliance of the S/C w.r.t. the frequency requirement from the Launcher Authority. Moreover, it allows to perform a consistent post-test correlation of the first lateral natural frequency of S/C FE model.

• Structural Engineering and Mechanics
• /
• v.15 no.1
• /
• pp.21-38
• /
• 2003

The formulation of a new bridge-vehicle system using shell with eccentric beam elements has been introduced in a companion paper (Part I). The new system takes into account of the contribution of the twisting and pitching modes of vehicles to the bridge responses. It can also be used to study the dynamic transverse load distribution of a bridge. This paper presents a parametric study on the impact induced by one vehicle or multi-vehicle running across a bridge using the proposed model. Several parameters were considered as variables including the mass ratio, the speed parameter, the frequency ratio and the axle spacing parameter to investigate their effects on the impact factor. A total number of 189 cases were carried out in this parametric study. Within the realistic range of vehicle considered, the maximum impact factors could be 2.24, 1.78 and 1.49 for bridges with spans 10 m, 20 m and 30 m respectively.

• Nuclear Engineering and Technology
• /
• v.28 no.3
• /
• pp.274-279
• /
• 1996

Diffusion coefficient is a critical parameter for predicting radiological source term(migration rate and flux of radionuclide) through given near field conditions in spent fuel or high level waste repository. The effect of exchangeable cation-$Na^+$ and $Ca^{2+} - on the diffusion of $I^- \;and^3H$ (as HTO) in compacted bentonite was examined using a through-diffusion method. Bentonite material used here was compacted to a density of 1.3 Mg/m$^3$, and Na-bentonite was saturated with a solution of 100 mol NaCl/m$^3$ and Ca-bentonite with 50 $mol\;CaCl_2$/m$^3$. The results show that effective diffusion coefficients are generally higher by a factor of two to five in Ca-than Na-clay. This is attributed to the larger particle size of Ca-compared to Na-bentonite; hence, Ca-bentonite has a greater proportion of relatively large pores, which make a greater contribution to mass transport than small pores. Although the nature of the exchangeable cation affects mass diffusion in compacted bentonite, the effect is small and not likely to influence performance assessment modeling of compacted bentonite-based barriers.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.4 no.4
• /
• pp.9-17
• /
• 2000

The crystal growth and dissolution rates were calculated by solving a model equation, which involved the dissolution of the metastable phase($\beta$-HNIW) and growth of the stable phase($\varepsilon$-HNIW), together with the mass balance equation. The model has been successfully used to simulate available kinetic data for the $\beta$$\longrightarrow$$\varepsilon$ polymorphic transformation via a solution phase. From the effectiveness factor based on the two-step model, it was found that the surface integration contribution to the process was comparatively small, and a diffusion dependency decreased with an increase of the mass fraction of chloroform in the mixed solvents of ethyl acetate and chloroform. Appling these kinetics in process simulation allowed for the prediction of the product size of $\varepsilon$-HNIW.

• The Journal of Asian Finance, Economics and Business
• /
• v.8 no.2
• /
• pp.523-531
• /
• 2021

This study aims to examine the role of social media marketing on the performance of micro-, small and medium-sized enterprises (MSMEs) during the COVID-19 pandemic. This research method uses a quantitative approach and the analytical tool used is Structural Equation Modeling (SEM) based on Partial Least Square. The sampling technique used purposive sampling and the sample in this study was MSMEs who use social media for marketing. The social media used are Facebook, Instagram, and Whatsapp. The number of samples in this study was 254 MSMEs. Data collection used online questionnaires. The research findings show that the use of social media marketing is influenced by compatibility, perceived usefulness, and perceived ease-of-use. The results of this study indicate that the use of social media for marketing has a positive effect on the performance of MSMEs, especially in increasing sales, customer relationships, productivity, and creativity. This means that the better the management of social media for marketing, the better the performance of MSMEs will be. The theoretical contribution to this research is built on the TAM and UTAUT theories and their impact on social media marketing on MSMEs in developing countries that are living through the COVID-19 pandemic.