• Advances in Computational Design
• /
• v.2 no.3
• /
• pp.123-141
• /
• 2017

Solving a system of linear or non-linear equations is required to analyze any kind of structures. There are many ways to solve a system of equations, and they can be classified as implicit and explicit techniques. The explicit methods eliminate round-off errors and use less memory. The dynamic relaxation method (DR) is one of the powerful and simple explicit processes. The important point is that the DR does not require to store the global stiffness matrix, for which it just uses the residual loads vector. In this paper, a new approach to the DR method is expressed. In this approach, the damping, mass and time steps are similar to those of the traditional method of dynamic relaxation. The difference of this proposed method is focused on the method of calculating the damping. The proposed method is expressed such that the time step is constant, damping is equal to zero except in steps with maximum energy and the concentrated damping can be applied to minimize the energy of system in this step. In this condition, the calculation of damping in all steps is not required. Then the volume of computation is reduced. The DR method for form-finding of membrane structures is employed in this paper. The form-finding of the three plans related to the membrane structures with different loading is considered to investigate the efficiency of the proposed method. The numerical results show that the convergence rate based on the proposed method increases in all cases than other methods.

• Geomechanics and Engineering
• /
• v.14 no.3
• /
• pp.271-281
• /
• 2018

A jointed rock slope stability evaluation was simulated by a discontinuous deformation analysis numerical method to investigate the process and safety factors for different crack distributions and different overloading situations. An optimized method using Discontinuous Deformation Analysis for Rock Failure (DDARF) is presented to perform numerical investigations on the jointed rock slope stability evaluation of the Dagangshan hydropower station. During the pre-processing of establishing the numerical model, an integrated software system including AutoCAD, Screen Capture, and Excel is adopted to facilitate the implementation of the numerical model with random joint network. These optimizations during the pre-processing stage of DDARF can remarkably improve the simulation efficiency, making it possible for complex model calculation. In the numerical investigations on the jointed rock slope stability evaluations using the optimized DDARF, three calculation schemes have been taken into account in the numerical model: (I) no joint; (II) two sets of regular parallel joints; and (III) multiple sets of random joints. This model is capable of replicating the entire processes including crack initiation, propagation, formation of shear zones, and local failures, and thus is able to provide constructive suggestions to supporting schemes for the slope. Meanwhile, the overloading numerical simulations under the same three schemes have also been performed. Overloading safety factors of the three schemes are 5.68, 2.42 and 1.39, respectively, which are obtained by analyzing the displacement evolutions of key monitoring points during overloading.

• Membrane and Water Treatment
• /
• v.11 no.1
• /
• pp.69-77
• /
• 2020

Former studies revealed that sepiolite thermally treated at high temperature have high adsorption capacity for phosphate. However, its micron size (75 ㎛) limits its application to water treatment. In this study, we synthesized sepiolite impregnated polysulfone (PSf) beads to separate it easily from an aqueous solution. PSf beads with different sepiolite ratios were synthesized and their efficiencies were compared. The PSf beads with 30% impregnated sepiolite (30SPL-PSf bead) possessed the optimum sepiolite ratio for phosphate removal. Kinetic, equilibrium, and thermodynamic adsorption experiments were performed using the 30SPL-PSf bead. Equilibrium adsorption was achieved in 24 h, and the pseudo-first-order model was suitable for describing the phosphate adsorption at different reaction times. The Langmuir model was appropriate for describing the phosphate adsorption onto the 30SPL-PSf bead, and the maximum adsorption capacity of the 30SPL-PSf bead obtained from the model was 24.48 mg-PO₄/g. Enthalpy and entropy increased during the phosphate adsorption onto the 30SPL-PSf bead, and Gibb's free energy at 35 ℃ was negative. An increase in the solution pH from 3 to 11 induced a decrease in the phosphate adsorption amount from 27.30 mg-PO₄/g to 21.54 mg-PO₄/g. The competitive anion influenced the phosphate adsorption onto the 30SPL-PSf bead was in the order of NO₃^- > SO₄^2- > HCO_3^-. The phosphate breakthrough from the column packed with the 30SPL-PSf bead began after ~2000 min, reaching the influent concentration after ~8000 min. The adsorption amounts per unit mass of 30SPL-PSf and removal efficiency were 0.775 mg-PO₄/g and 61.6%, respectively. This study demonstrates the adequate performance of 30SPL-PSf beads as a filter for phosphate removal from aqueous solutions.

• Journal of computational fluids engineering
• /
• v.18 no.3
• /
• pp.1-7
• /
• 2013

A pure oxygen combustion technology is crucial in Carbon Capture and Storage (CCS) technology especially in capturing of $CO_2$, where CCS will reduce 9 $GtCO_2$ by 2050, which is 19% of the total $CO_2$ reduction amount. To make pure oxygen combustion feasible, a regenerative system is required to enhance the efficiency of pure oxygen combustion system. However, an existing air combustion technology is not directly applicable due to the absence of nitrogen that occupies the 78% of air. This study, therefore, investigates the heat and fluid flow in a regenerative system for pure oxygen combustion by using commercial CFD software, FLUENT. Our regenerative system is composed of aluminium packed spheres. The effect of the amount of packed spheres in regenerator and the effect of presence or absence of a bypass of exhaust gas are investigated. The more thermal mass in regenerator makes the steady-state time longer and temperature variation between heating and regenerating cycle smaller. In the case of absence of bypass, the regenerator saturates because of enthalpy imbalance between exhaust gas and oxygen. We find that 40% of exhaust gas is to be bypassed to prevent the saturation of regenerator.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.37 no.9
• /
• pp.847-854
• /
• 2013

The objective of this study is to experimentally investigate the mixed flow and oxygen transfer characteristics of a horizontally injected aeration process using an annular nozzle ejector. The flow rate ratio, pressure ratio and ejector efficiency are calculated using the measured flow rate and pressure with the experimental parameters of the ejector pitch and primary flow rate. The visualization images of mixed flow issuing from the ejector are analyzed qualitatively, and the volumetric oxygen transfer coefficients are calculated using the measured dissolved oxygen concentration. The mixed flow behaves like a buoyancy jet or horizontal jet owing to the momentum of primary flow and air bubble size. The buoyancy force of the air bubble and the penetration of mixed flow are found to be important parameters for the oxygen transfer rate owing to the contact area and time of two phases.

• Asian-Australasian Journal of Animal Sciences
• /
• v.33 no.11
• /
• pp.1770-1778
• /
• 2020

Objective: This study was conducted to reveal potential metabolic differences of dairy cows fed corn stover (CS) and rice straw (RS) instead of alfalfa hay (AH) as main forage source. Methods: Thirty multiparous mid-late lactation Holstein dairy cows were selected and randomly assigned to three diets, AH, CS, or RS (n = 10). After 13 weeks of the feeding trial, coccygeal arterial and superficial epigastric venous plasma samples were collected before morning feeding for gas chromatography time-of-flight/mass spectrometry analyses. Results: In the artery, 8 and 13 metabolites were detected as differential metabolites between AH and CS, and between AH and RS, respectively. The relative abundance of phenylpropanoate (log₂fold change [FC]) = 1.30, 1.09), panthenol (log₂FC = 2.36, 2.20), threitol (log₂FC = 1.00, 1.07), and 3,7,12-trihydroxycoprostane (log₂FC = 0.79, 0.78) were greater in both CS and RS than in AH, and tyrosine (log₂FC = -0.32), phenylalanine (log₂FC = -0.30), and pyruvic acid (log₂FC = -0.30) were lower in RS than in AH. In the vein, 1 and 7 metabolites were detected as differential metabolites between AH and CS, and between AH and RS, respectively. By comparing AH and RS, we found that metabolic pathways of phenylalanine, tyrosine, and tryptophan biosynthesis and phenylalanine metabolism were enriched by integrative artery and vein analysis. Furthermore, AH and RS, arterial phenylpropanoate and 4-hydroxyproline were positively, and phenylalanine was negatively correlated with milk urea nitrogen. Finally, in AH and CS, arterial panthenol was negatively correlated with feed efficiency. Conclusion: Arterial metabolic profiles changed more than those in the veins from animals on three forage diets, differing in amino acids. We found that phenylalanine, tyrosine, and tryptophan biosynthesis and phenylalanine metabolism were restricted when cows were fed low-quality cereal straw diets.

• Journal of the Korean Institute of Intelligent Systems
• /
• v.20 no.1
• /
• pp.88-93
• /
• 2010

In this paper, an edge detecting sensor using ultrasonic detection module is developed which will be used for areas of industrial applications such as plastic film winding system, cloth winding system, paper roll industry, etc. The developed sensor have properties that more exactly detect the edge line, that less affected by environmental noise, and that it produced more stable measurement output. The mass of the winding object is dominantly affect the dynamics of the system and it could produce undesirable result of the system such as stability of the closed-loop system and accuracy of edge-line-following-control(ELFC) objective. Also, there exist sensor noise due to the mechanical vibration or other environmental effect. These noise also degrade the efficiency of control system. In order to compensate these problems, this paper present a fuzzy PI/PID edge-line-controller, and which is designed and implemented.

• Journal of Advanced Marine Engineering and Technology
• /
• v.35 no.2
• /
• pp.175-181
• /
• 2011

The purpose of this study is to secure the design data for the optimization of the radial turbine and heat cycle system, by using the CFD analysis technique and the design of 100kW class radial turbine applicable to waste heat recovery generation system for ship. Radial turbine was comprised of scroll casing, vane nozzle with 18 blades and rotor with 13 blades, and analysis grid was used to about 2.3 million. Mass flow rate and rotational speed was 0.5kg/s, 75,0000rpm, respectively. Eight kinds of inlet pressure was set between 195 and 620kPa. As the flow accelerated through the nozzle passage to the throat, the pressure level at the pressure and suction sides becomed similar to about Mach number of 0.35. When the inlet temperature and pressure was $250^{\circ}C$, 352kPa respectively, the isentropic efficiency and mechanical power showed the analysis results of 74% and 108kW.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.35 no.12
• /
• pp.1383-1389
• /
• 2011

The current study focuses on the consistent analysis of heat transfer in multichannel volumetric solar receivers used for concentrating solar power. Changes in the properties of the absorbing material and channel dimensions are considered in an optical model based on the Monte Carlo ray-tracing method and in a one-dimensional heat transfer model that includes conduction, convection, and radiation. The optical model results show that most of the solar radiation energy is absorbed within a very small channel length of around 15 mm because of the large length-to-radius ratio. Classification of radiation losses reveals that at low absorptivity, increased reflection losses cause reduction of the receiver efficiency, notwithstanding the decrease in the emission loss. As the average temperature increases because of the large channel radius or small mass flow rate, both emission and reflection losses increase but the effect of emission losses prevails.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.188.1-188.1
• /
• 2014

Aluminum is widely used as a material for electrode on silicon based devices. Especially, aluminum films are used as backside and front-side electrodes in silicon quantum dot (QD) solar cells. In this point, the diffusion of aluminum is very important for the enhancement of power conversion efficiency by improvement of contact property. Aluminum was deposited on a Si (100) wafer and a Si QD layer by ion beam sputter system with a DC ion gun. The Si QD layer was fabricated by $1100^{\circ}C$ annealing of the $SiO_2/SiO_1$ multilayer film grown by ion beam sputtering deposition. Cs ion beam with a low energy and a grazing incidence angle was used in SIMS depth profiling analysis to obtain high depth resolution. Diffusion behavior of aluminum in the Al/Si and Al/Si QD interfaces was investigated by secondary ion mass spectrometry (SIMS) as a function of heat treatment temperature. It was found that aluminum is diffused into Si substrate at $450^{\circ}C$. In this presentation, the effect of heat treatment temperature and Si nitride diffusion barrier on the diffusion of Al will be discussed.