• Journal of the Korean Institute of Telematics and Electronics
• /
• v.18 no.1
• /
• pp.51-56
• /
• 1981

A new I2L process for a high performance I2L structure is proposed. The modifiedstructure consists of a heavily doped extrinsic base and lowly doped intrinsic base where the collector regions are self-alignment with the intrinsic base regions. The proposed process untilizes spin-on sources as the diffusion sources and the self-alignment of collectors is achieved by using the hardened spin-on source as a diffusion mask. Test devices including a 13-stage ring oscillator have been fabricated by the proposed process on n/n+ silicon wafers with 6.5$\mu$m epitaxial layer. The maximum upward current gain of npn transistors is 8 for a three collector I2L cell. The speed-power product and minimum propagation delay for a one collector structure are 3.5 pJ and 50 ns, respectively.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.05c
• /
• pp.141-144
• /
• 2003

This study proposes ZnO thin film as a piezoelectric material for SAW (surface acoustic wave) filter. The ZnO thin film with thickness $2.6{\mu}m$ was deposited (0001)-oriented sapphire by RF magnetron sputtering technique. IDTs (inter-digital transducers) electrodes were patterned upon SAW filter mask with solid finger structure unapodized using lift-off method on ZnO piezoelectric thin film. SAW propagation velocity was measured with the center frequency by HP 8753C network analyzer. A fabricated ZnO SAW filter exhibited a high propagation velocity of 5433 $^m/s$ and relatively insertion loss of -53.391dB at $\lambda=80{\mu}m$. The side-lobe attenuation of the center frequency was about 17dB. When the wavelength was $80{\mu}m$ $(\lambda/4=20{\mu}m)$, the center frequency was 67.907 MHz. $k^2$ (electromechanical coupling coefficient) was 15.84 %.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2003.10a
• /
• pp.391-394
• /
• 2003

Laser direct writing process is developed 3rd harmonic Diode Pumped Solid State Laser with the near visible wavelength of 355 m sensitive polymer is irradiated by UV laser and developed using polymer solvent to obtain quasi-3D. It is important to reduce line width for image mode waveguides, so some investigations will be carried out in various conditions of process parameters such as laser power, writing speed, laser focus and optical properties of polymer. This process could be to fabricate a single mode waveguide without expensive mask projection method. Experimentally, the patterns of trapezoidal shape were manufactured into dimension of 8.4 mm width and 7.5 mm height. Propagation loss of straight waveguide measured 3 dB/cm at 1,550 nm.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1996.11a
• /
• pp.40-43
• /
• 1996

Substrates of SAW filter are mainly single crystal such as LiNbO$_3$, LiTaO$_3$. However, fabrication of crystal is difficult and cost is very high. In this study, crystal was substituted for piezoelectric ceramics which has simple fabrication process. The same SAW filter mask was photolithographed on crystal(LiNbO$_3$) substrate and ceramic(PZT4, PZT5A and PZT8) substrate in order to compare experimental value with theoretical value. The difference of center frequency was only 3.7%. PZT8 showed good bandwidth properties. It is considered that PZT8 has higher mechanical quality factor and propagation velocity than PZT4, PTT5A.

• Journal of the Korean Institute of Telematics and Electronics B
• /
• v.33B no.10
• /
• pp.63-71
• /
• 1996

This paper proposes a method which analyzes facial shape and extracts positions of eyes regardless of the tilt and the size of input iamge. With the extracted feature parameters of facial element by the method, full human faces are recognized by a neural network which BP algorithm is applied on. Input image is changed into binary codes, and then labelled. Area, circumference, and circular degree of the labelled binary image are obtained by using chain code and defined as feature parameters of face image. We first extract two eyes from the similarity and distance of feature parameter of each facial element, and then input face image is corrected by standardizing on two extracted eyes. After a mask is genrated line historgram is applied to finding the feature points of facial elements. Distances and angles between the feature points are used as parameters to recognize full face. To show the validity learning algorithm. We confirmed that the proposed algorithm shows 100% recognition rate on both learned and non-learned data for 20 persons.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.24 no.5
• /
• pp.786-793
• /
• 1987

This paper describes the design and fabrication of the polysilicon selfaligned bipolar transistor with 1.6\ulcorner epitaxy and SWAMI isolation technologies. This transistor has two levels of polysilicon. Also emitter and adjacent edge of polysilicon base contact of this PSA device are defined by the same mask, and emitter feature size is 2x4 \ulcorner. DC characteristic of the fabricated transistor was evaluated and analyzed for the SPICE input parameters. The minimum propagation delay time per gate of 330 ps at 1mW was obtained with 41 stage CML ring oscillator.

• Journal of Sensor Science and Technology
• /
• v.3 no.1
• /
• pp.40-45
• /
• 1994

$112^{\circ}$ rot. x-cut $LiTaO_{3}$ wafer was used as the substrate of SAW gas sensor. Dual delay line SAW device with IDTs which consist of the reference delay line and the sensing delay line was fabricated using photolithigraphy. Each IDTs had 10 finger pairs and finger spacing is 10 microns. One delay line channel is the reference, while the second is the sensing channel with Pb-phthalocyanine film in the propagation path. Pb-phthalocyanine film which is p-type organic semiconductor was evaporated in $10^{-5}$ torr vacuum using shadow mask selectively. Dual delay line oscillator was constructed by using the rf amplifier and AGC. Frequency of the IDTs had the range of $87{\sim}$89 MHz oscillation frequency. Oscillation frequency shifts were investigated as a function of the temperature and the concentration of $NO_{2}$ gas.

• Journal of the Institute of Convergence Signal Processing
• /
• v.21 no.3
• /
• pp.113-120
• /
• 2020

With the recent development of communication equipment, the demand for communication equipment is gradually increasing. Accordingly, various signal processing has been studied. In the case of an image, noise removal is an indispensable step because noise propagation problems may occur if noise is not removed in the pre-processing process. Salt and Pepper noise is a typical impulse noise with two extremes. Various studies have been conducted to remove such noise, and there are CWMF, MF and MMF. However, the existing methods are somewhat insufficient in the high-density noise region. Therefore, in this study, we have proposed an algorithm that filters the size of the mask according to the number of noises inside the 7×7 mask and filters it with a modified switching filter using the histogram distribution of the image. In the case of the proposed algorithm, noise can be effectively removed in a high-density noise region. For objective judgment, PSNR was used to compare and analyze with existing algorithms.

• Current Optics and Photonics
• /
• v.8 no.4
• /
• pp.355-365
• /
• 2024

Wavefront coding (WFC) imaging systems can redistribute the energy of an interference laser spot on an image plane sensor by wavefront phase modulation and reduce the peak intensity, realizing laser protection while maintaining imaging functionality by leveraging algorithmic post-processing. In this paper, a spiral axicon WFC imaging system is proposed, and the performance for laser protection is investigated by constructing a laser transmission model. An Airy disk on an image plane sensor is refactored into a symmetrical hollow ring by a spiral axicon phase mask, and the maximum intensity can be reduced to lower than 1% and single-pixel power to 1.2%. The spiral axicon phase mask exhibits strong robustness to the position of the interference laser source and can effectively reduce the risk of sensor damage for an almost arbitrary lase propagation distance. Moreover, we revealed that there is a sensor hazard distance for both conventional and WFC imaging systems where the maximum single-pixel power reaches a peak value under irradiation of a power-fixed laser source. Our findings can offer guidance for the anti-laser reinforcement design of photoelectric imaging systems, thereby enhancing the adaptability of imaging systems in a complex laser environment. The laser blinding-resistant imaging system has potential applications in security monitoring, autonomous driving, and intense-laser-pulse experiments.

• Annual Conference on Human and Language Technology
• /
• 1989.10a
• /
• pp.137-141
• /
• 1989

본 논문에서는 신경망 구조의 한 모델인 feed-forward multi-layered network에 역전파 학습(back-propagation learning) 기법을 이용하여 필기체 한글 숫자를 인식하고 그 가능성을 보였다. 문자 인식에 있어 입력 대상의 모양이 왜곡되거나, 대상의 크기 혹은 위치의 변화 등과 같은 잡음 (noise)에 대해서 정확히 대상을 인식하는 데는 대상의 구조 추출에 크게 관여되므로 한글의 구조 추출에 적합하다고 생각되는 bar mask 투사법을 제안하였다. 모델의 학습을 필기체 한글 숫자 16자의 입력 패턴과 타겟 ( target) 입력의 쌍을 이용해 학습시켰다. 또한, 모델의 인식 정도를 측정해 보기 위해 시험패턴을 적용하여 훈련된 패턴과 훈련되지 않은 패턴간의 인식률을 비교하여 보았다.