• Journal of Advanced Marine Engineering and Technology
• /
• 제28권8호
• /
• pp.1203-1210
• /
• 2004

It was reported recently that the pump head degradation near the best efficiency point from single-phase flow to the break-down due to air entrainment became less in a screw-type centrifugal pump than in a general centrifugal pump. In this paper, I carried out internal pressure measurements and visualizations, and investigated the various physical phenomena occurring inside a screw-type centrifugal pump operated in air-water two-phase flow. The results could give some characteristics about the degradation of pump performance on air-water two-phase flow.

• 한국항해항만학회:학술대회논문집
• /
• 한국항해항만학회 2006년도 Asia Navigation Conference
• /
• pp.95-104
• /
• 2006

A floating-type wave power pump is a device which sends air into water by using wave power. The floating-type wave power pump has the new configuration composed of a curved surface reflection board, a slope, and phase plates. As a result of a water-tank experiment it turned out that the floating-type wave power pump with a curved surface reflection board and a slope raised power and efficiency in the wide wavelength waves. The result of a marine experiment was also preferable. The floating-type wave power pump sends air into the sea by using wave power, so it can be used for the improvement of marine environment. In addition, the floating body constituted of a curved surface reflection board, a slope, and phase plates, is effective as a device to utilize the energy of a wave. Therefore, it can be widely used for a wave power generation, pumping up deep seawater.

• 수산해양기술연구
• /
• 제51권3호
• /
• pp.279-284
• /
• 2015

Generally, there are many kinds of pumps used on a ship, which play an obbligato role to assist the ship's running. However, due to the pump's own motor, it becomes a main vibration resource that may cause serious problems in local. If the above situation happened, it may cause local resonance even structural damage. Also, the bigger the pump's size is, the more serious the vibration is. Therefore, it is very important for researchers to estimate the vibrations situation of pumps accurately and avoid or reduce the probability of resonance. Based on a real marine pump-HHG8065, this paper did a vibration analysis by FEM (Finite Element Method) and compared the results with actual test. Finally, it gave a discussion on the estimation of pump and provided an improvement way to the vibration level.

• 한국산업융합학회 논문집
• /
• 제25권6_2호
• /
• pp.1063-1069
• /
• 2022

In modern industry, vacuum has grown into an indispensable industrial field. The performance of the vacuum pump in the degasser system among mud treatment system facilities was verified by a numerical analysis method. The degasser system is an equipment for removing the gas contained in the mud, and it is a work process that requires a vacuum. This study analyzed the vacuum pump performance of the degasser used in drilling for resource development of onshore and offshore plants. The vacuum pump used in the degasser system was designed with a discharge rate of 0.099kg/s. The DM(Design Modeler) program of ansys workbench 17.2 was used to modify the model of the vacuum pump used in the degasser system. And for performance analysis, CFX, which is known to be suitable for rotating system analysis, was used. Finally the performance analysis results of the vacuum pump and the prototype performance test results were compared and analyzed.

• 한국기계가공학회지
• /
• 제11권6호
• /
• pp.123-129
• /
• 2012

This study was carried out to improve the design of fuel injection pump for marine medium diesel engine. For this purpose, all parts of fuel injection pump were modeled and simulated using CATIA V5R19, FLUENT & MSC Nastran. Flow analysis for plunger cylinder and structural analysis for plunger, roller and spring, which were considered as essential parts of fuel injection pump, were performed to find the optimal design of fuel injection pump. As the results, flow of fluid in plunger cylinder was showed good results in case of 7.7~8.0m/s of plunger velocity. Furthermore, it was confirmed that plunger, roller and spring could be operated safely under 1,800bar pressure.

• 해양환경안전학회지
• /
• 제20권6호
• /
• pp.788-793
• /
• 2014

본 연구에서는 선박용 해수펌프에 회전수를 제어할 수 있는 인버터를 설치하여 효율적인 유량제어를 통한 소비전력 절감효과를 확인하고 해양생성물 부착방지시스템(MGPS)이 미설치된 곳에서 해수펌프의 유량제어가 시스템에 미치는 영향에 관하여 연구하였다. 실험은 항해중이나 정박중 항시 운전되고 있는 목포해양대학교의 실습선의 보조해수펌프와 냉동기 해수펌프를 이용하였으며, 정박과 국제항해로 구분하여 실험하였다. 연구 결과 해수온도가 $18^{\circ}C$이하인 경우 펌프회전수는 58.3 % 감소시켜 운전이 가능하였으며 50 %의 소비전력 절감효과가 있었다. 해수온도가 $34^{\circ}C$까지 상승하여도 펌프의 회전수는 91.6 %로 운전이 가능하였으며 20 %의 소비전력 절감효과가 있었다. 또한 해양생성물 부착방지시스템이 설치되지 않은 곳에서는 펌프의 회전수를 낮추어 유속이 저하하면 해양생성물의 부착을 가증시키는 결과를 알게 되었다.

• Journal of Advanced Marine Engineering and Technology
• /
• 제28권2호
• /
• pp.376-381
• /
• 2004

A rig was constructed to test the performance characteristics and compare the hydraulic forces exerted on a centrifugal type artificial heart impeller. A conventional shaft. seal and bearing system. while driven by a small electric motor. supported the impeller which was separated from the pump casing by a six degree of freedom force transducer (JR3 Ine). Radial (x. y) and axial (z) hydraulic forces were recorded and compared. At physiological operating conditions. the results indicate that the double entry/exit centrifugal pump encounters a smaller radial force and significantly reduced axial thrust. These experimental results are valuable in the design of a magnetic bearing system to suspend the impeller of a centrifugal artificial heart pump. This experimental technique may also be applied to evaluate the required capacity and predict the lifetime of contact bearings in marine pumps.

• Journal of Advanced Marine Engineering and Technology
• /
• 제22권1호
• /
• pp.92-99
• /
• 1998

Unsteady flow problems created by hydraulic transients in pipeline systems with pump are of significant importance because they can cause excessive pressure, cavitation, vibration and noise. In this paper, an analysis of transient flow for the pump pipelines is developed by means of the characteristic method. The calculated results of the program to simulate water hammer due to sudden valve closure in a simple pipeline are compared with those of the analytical method. Expecially the water hammer due to power failure in pump pipeline system with surge tank was simulated. As the results, both the upsurge and the downsurge along the pipeline are reduced.

• Journal of Advanced Marine Engineering and Technology
• /
• 제31권8호
• /
• pp.1035-1041
• /
• 2007

An improvement of driving motor burning damages on a couplingless type warship fire pump is studied. The pump consists of an induction motor a pump-motor shaft and a volute type impeller. The burning damage had occured by changing the material of the pump-motor shaft from carbon steel(SM 45C) to stainless steel(STS 316) for improving anti-corrision properity in sea water. It is shown that a material change on the pump-motor shaft can reduce the efficiency of driving motor and may cause motor burning in the process of pump development stage. This kind of motor burning problem can be solved by increasing the efficiency of the motor and changing the geometry of the inner parts.

• 한국산학기술학회논문지
• /
• 제16권11호
• /
• pp.7878-7884
• /
• 2015

해수의 접촉이 많은 금속 임펠러는 해수의 염분에 의해 부식이 되므로 탄소섬유로 제작된 임펠러를 사용한 해수펌프가 개발되었다. 해수펌프의 임펠러와 와류실의 최적설계를 수치해석을 통해 수행하였고 관련인자(임펠러 두께, 표면 거칠기)의 영향을 평가하였다. 임펠러의 두께는 무게 때문에 재료에 따라 제한된다. 탄소섬유를 사용한 임펠러는 경량이므로 최대효율을 나타내는 임펠러 두께를 사용할 수 있다. 표면 거칠기의 경우 같은 운전 조건에서 펌프의 효율에 7 % 범위에서 영향을 주는 것을 확인하였다.