• Journal of Advanced Marine Engineering and Technology
• /
• v.38 no.6
• /
• pp.658-665
• /
• 2014

Natural gas for marine diesel engine is considered as an important and clean source of energy because of simultaneously reducing the emission of NOx, SOx and GHG. Especially with a appearance of shale gas, the using of natural gas has been investigated aggressively and expected to expand rapidly. By the reports, gas engine and diesel engine were both in a similar performance in the power aspect, and the SFOC of gas engine was shown a little better than that of diesel engine. But the characteristics of exhaust gas emission were different according to various combustion technologies. And with lean burn technology, the emission of NOx could be reduced to 85% lower than that of diesel engine. In this paper, it was described that a simulation program has been developed to predict NOx emission. The developed program is adopted two-zone model and Wiebe function for combustion in cylinder. The effects of premixed and diffusive combustion could be simulated by using the excess air ratio as input data. And it was confirmed that the results of simulation were agreed with the general trends of exhaust gas emission according to various combustion conditions such as lean burn, premixed and diffusive combustion.

• Journal of Advanced Marine Engineering and Technology
• /
• v.38 no.10
• /
• pp.1251-1256
• /
• 2014

The use of lubrication oil is of many purposes and one among them is to drive the engine mounted on a ship. Hence the supply of clean lubrication oil is important. And an oil purifier is one of key components in marine diesel engines. At present, the element type full-flow oil filter has been widely used for cleaning the engine oil. The self-driven centrifugal oil purifier is a device which is used to remove the impurities in lubrication oil using a jet flow. The flow characteristics and the physical behaviors of particles in this self-driven oil purifier were investigated numerically and the filtration efficiencies were evaluated. For calculations, a Computational Fluid Dynamics method is used and the Shear Stress Transport turbulence model has been adopted. The Multi Frames of Reference method is used to consider the rotating effect of the flows. The influence of centrifugal forcehas been numerically investigatedto improve filtration efficiency of tiny particles. As a result of this research, it was found that the particle filtration efficiency using the only center axis rotating and outer wall rotating system are higher than that of the fully rotating system in the self-driven oil purifier.

• Proceedings of the KIEE Conference
• /
• 2011.07a
• /
• pp.1228-1229
• /
• 2011

A novel approach has been promoted for FNN ship controllers. An Electro-hydraulic governor has been widely adopted to the ship speed control of propulsion marine diesel engines for a long time, it was very difficult for Electro-hydraulic governor to regulate the speed of high power engine with long stroke at low speed and low load, because of the jiggling phenomena by rough fluctuation of rotating torque and the hunting phenomena by long dead time occurred in fuel combustion process in the engine cylinder. This paper provides an efficient way for improving control performance by FNN controller. An RBF neural network and GA optimization are employed in a fuzzy neural controller to deal with the nonlinearity, time varying and uncertain factors, the rule base and membership functions can be auto-adjusted by GA optimization. The parameters of neural network can be decreased by using union-rule configuration in the hidden layer of the network. The performance of controller is evaluated by the system simulation using simulink tools.

• Proceedings of the Korean Society of Marine Engineers Conference
• /
• 2005.11a
• /
• pp.11-12
• /
• 2005

BMS & Governor System은 선박용 추진 기관으로 사용되는 저속 디젤 엔진의 원격 운전 및 제어를 담당하는 시스템으로 선박 추진과 엔진 제어에 필수적인 중요 구성 요소이며, 조선 기자재관련 고부가가치 산업의 한 부분이다. 그러나 조선관련 산업에 있어서 세계 최강국의 위상에 걸맞지 않게 국내에는 BMS & Governor System의 독자 모델이 없는 실정이고, 유럽이나 일본의 제품으로 전량 수입에 의존하고 있는 상황이다. 이에 선박 추진용 저속 디젤 엔진을 위한 제어 시스템의 관련 기술을 연구하여, SEA-CAPS를 개발하였다. 본 연구에서는 BMS & Governor System에 대한 개요와 SEA-CAPS의 개발 내용, 그리고 환경 및 성능 시험에 관한 내용을 언급하고자 한다.

• Journal of Advanced Marine Engineering and Technology
• /
• v.30 no.2
• /
• pp.247-252
• /
• 2006

Almost ship monitoring systems are event driven alarm system which warn only when the measurement value is over or under set point. These kinds of system cannot warn until signal is growing to abnormal state that the signal is over or under the set point. therefore cannot play a role for preventive maintenance system. This paper proposes fault diagnosis method which is able to diagnose and forecast the fault from present operating condition by analyzing monitored signals with present ship monitoring system without any additional sensors. By analyzing the data with high correlation coefficient(CC), correlation level of interactive data can be defined. Knowledge base of abnormal detection can be built by referring level of CC(Fault Detection CC. FDCC) to detect abnormal data among monitored data from monitoring system and knowledge base of diagnosis built by referring CC among interactive data for related machine each other to diagnose fault part.

• Proceedings of the Korean Society of Marine Engineers Conference
• /
• 2005.06a
• /
• pp.281-286
• /
• 2005

Almost ship monitoring systems are event driven alarm system which warn only when the measurement value is over or under set point. These kinds of system cannot warn while signal is growing to abnormal state until the signal is over or under the set point and cannot play a role for preventive maintenance system. This paper proposes fault diagnosis method which is able to diagnose and forecast the fault from present operating condition by analyzing monitored signals with present ship monitoring system without additional sensors. By analyzing this data having high correlation coefficient(CC), correlation level of interactive data can be understood. Knowledge base of abnormal detection can be built by referring level of CC(Fault Detection CC, FDCC) to detect abnormal data among monitored data from monitoring system and knowledge base of diagnosis built by referring CC among interactive data for related machine each other to diagnose fault part.

• Journal of Advanced Marine Engineering and Technology
• /
• v.26 no.6
• /
• pp.705-711
• /
• 2002

디젤기관은 실린더 내경의 크기, 실린더 수 및 회전수에 따라 착화지연, 연소지연 및 디젤기관의 각종 정수가 달라지므로 비선형이 심한 시스템이다. 본 연구에서는 신경회로망을 이용하여 발전기를 구동하는 디젤 기관의 속도를 제어하는 디젤기관 신경회로망 디지털조속기를 제안한다. 이를 위하여 3상 50㎾ 발전기를 구동하는 4행정 4실린더, 1800 rpm ISUTSU 디젤기관의 실제 운전데이터로부터 뉴럴에뮬레이터를 구한다. 최적치 뉴럴에뮬레이터 구성을 위하여 다양한 역전파알고리즘으로 학습을 행하고 결과를 비교한다. 또한 디젤기관의 역으로부터 뉴럴 제어기를 구성하고 뉴럴에뮬레이터로 시뮬레이션을 행한다. 외란이 존재하는 경우에도 효과적인 뉴럴제어기를 구성하기 위하여 선택적 뉴럴제어 기의 사용을 제안한다. 또한 응답성을 향상하고 정확한 목표치추종을 위하여 PI제어기를 보조제어기로 사용하는 하이브리드제어기를 구성하여 시뮬레이션을 통하여 성능이 향상됨을 보인다.

• Journal of Advanced Marine Engineering and Technology
• /
• v.39 no.6
• /
• pp.626-632
• /
• 2015

The International Maritime Organization (IMO) has adopted several regulations for the prevention of air pollution from ships. In addition, there is a requirement for shipping liners to reduce greenhouse gas emissions. Accordingly, we need to take measurements to ensure that the steps taken are both efficient and environmentally friendly. It has been determined that the application of the Miller cycle in diesel engines has the effect of both reducing the amount of NOx and improving thermal efficiency. However, this method requires a considerably larger charge air pressure. Therefore, we consider a two-stage turbo-charging system, which not only results in a high charging pressure, but also improves the part load performance with an exhaust-gas bypass system or the application of the Miller cycle. Because of complications associated with the two-stage turbo-charging system, it is complex and difficult to realize a design that optimizes matching between diesel engine and turbo-chargers. Accordingly, it is necessary to perform a quantitative analysis to determine the effects and optimal conditions of these different systems in the early stage of system design. In this paper, we develop a simulation program to model these systems, and we verify that the results of this program are reliable. Further, we discuss methods that can be employed to improve its efficiency.

• Journal of Advanced Marine Engineering and Technology
• /
• v.37 no.4
• /
• pp.332-337
• /
• 2013

National investment was performed in the research and development of renewable energy because of climate change by air pollution, exhaustion of energy sources, energy security, and so on. Biodiesel fuel of the renewable energy is highlighted as friendly environment energy, it is possible to operate in regular diesel engines when it is blended with invariable ratios without making any changes. Emission factors have been estimated for commercial ship from various research institutes; however, it is difficult to develop emission factors for military vessels. In this work, biodiesel blended fuel emission factors for sulfur dioxide and carbon dioxide were quantitatively estimated from propulsive diesel engine installed on naval vessel using fuel property analysis. In addition, exhaust emissions were quantitatively calculated on the basis of fuel consumption rate with biodiesel content by percentage.

• Journal of Advanced Marine Engineering and Technology
• /
• v.22 no.6
• /
• pp.827-835
• /
• 1998

The effects of recirculated exhaust gas on the wear of cylinder liner piston and piston rings have been investigated by the experiment with a two-cylinder four cycle indirect injection diesel engine operating at 75% load and 1600 rpm speed For the purpose of comparison between the rates of two cylinders with and without EGR the recirculated exhaust gas is sucked into one of two cylinders after the soot among exhaust emissions is removed by an intntionally designed cylinder-type scrubber equipped with 6 water injectors(A water injector has 144 nozzles of 1.0 mm diame-ter) while only the fresh air into another cylinder. These experiments are carried out on the fuel injection at a fixed $15.3^{\circ}$ BTDC timing. It is found that firstly the mean wear amount of cylinder liner with EGR is more increased in the measurement positions of the second half than of the first half and the mean wear amount without EGR is almost uniform regardless of measurement posi-tions secondly the wear rates of the first and second piston ring(compression ring)thickness with EGR are more than twice but the wear rate of oil ring thickness without EGR is more increased than that with EGR and finally the wear rate of piston skirt with EGR is a little bit increased but the piston hed diameter is rather increased owing to soot adhesion and corrosion wear and espe-cially larger with EGR.