• Magazine of the Korean Society of Agricultural Engineers
• /
• v.43 no.6
• /
• pp.127-134
• /
• 2001

In order to expand agricultural lands in the western and southern coasts of Korean Peninsula, coarse soils excavated from hillsides have been used as fill materials for reclamation. In order to tackle with the problems and to confirm availability, research on soil improvement involve mixing cement to the fine wet soils. Required undrained shear strength$(C_u)$ for fill material was analysed to be 0.34~1.2 $kgf/cm^2$. It has been known that when cement is added to high water content marine clay its unconfined compression strength increased to 2 $kgf/cm^2$. Consolidation results show that pre-consolidation pressure increased to 1.8 $kgf/cm^2$and 3.4 $kgf/cm^2$ with the addition of 3% and 5% of cement respectively. This result shows that low-height embankments could be constructed without significant compression. Since the effectiveness of improvement may be different site by site, the mix design for each site is necessary in order to optimize it. The process is first to determine aimed shear strength and then optimum mix ratio of cement after carrying out a series of tests.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2009.03a
• /
• pp.640-648
• /
• 2009

Recently the truction of coastal reclaimation work has been extensively implemented in Korea. The Sondo New City is being established on the reclaimed land from the sea, construction companies of metro construction are planing to pull-out the sheet pile for saving the construction cost. In the case of soft marine clay, it is very difficult to pull-out the sheet pile by using the hydraulic hammer difficult. Therefore, the man of the field must be aware of vibration effect to the ground and the structure. For understanding the vibration effect to the ground during subway construction, the model was formulated with 1/25 braced-cut for subway construction. Scott and Iai(1989) proposed the law of the similarity for other experimental conditions. The laboratory model test was conducted under the vibration condition of sheet pile pulling out. The settlement on the ground surface was measured during the shaking table test. The pore water pressure was also monitored in the upper, middle, and lower layers of soil. The field settlement level and the pore water pressure can be predicted by using the results of the laboratory shaking table test.

• Proceedings of the Korean Geotechical Society Conference
• /
• 1992.12a
• /
• pp.33-66
• /
• 1992

Recently, waste landfills built on seashores have been increased because of the easy availability of broad area near the urban communities. To evaluate the performance of the marine clay landfill liner numerical contaminant transport analyses are performed by selecting the typical section of a waste landfill built on seashores and using hydraulic conductivity data obtained from the site. Also, the laboratory electrical resistivity test and the in-situ corrosion test are performed in order to analyze the influence of the soil and leachates composing the landfills on the construct ion materials. From the results of contaminant transport analyses, it is shown that the leachates can be migrated faster through narrow pervious channels than the wide homogeneous pervious tedium and the importance of good quality barriers to prevent the contaminant migration is recognized. In the laboratory electrical resistivity test all the earth materials except the cover soils saturated with distilled water have small resistivities, which shows a high potential of corrosivity of soils composing landfills. However, the degree of corrosion of specimens buried in the landfills was not so severe except the zinc and carbon steel specimens. This apparently conflict results present the necessity of the investigation of other major factors and the long term in-situ corrosion test.

• Journal of the Korean Geosynthetics Society
• /
• v.4 no.3
• /
• pp.45-52
• /
• 2005

Most marine structures are constructed on very soft soil, soil improvements are needed for the area of road, buildings. In this paper, some considerations of several case studies on soil placement method after geotextile placement, known as surface treatment, are done. Considerations of strength applicability on the advanced construction method of sand and soil placement are proposed in this paper. Typical tensile strength of geotextile used in the surface soil stabilization method is 15t/m, and thickness of sand and soil placement between 1.6m and 3.1m. Undrained shear strength of soft clay layer ranges $0.2{\sim}1.2t/m^2$. In order to minimize the difficulties which include soil disturbance, soft soil gush and overturn of vertical drain installation rig more studies are needed.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2002.10a
• /
• pp.665-672
• /
• 2002

In order to expand agricultural lands in the western and southern coasts of Korean Peninsula, coarse soils excavated from hillsides have been used as fill materials for reclamation. In order to tackle with the problems and to confirm availability, research on soil improvement involve mixing cement to the fine wet soils. Required undrained shear strength(c$\sub$u/) for fill material was analyzed to be 0.34∼1.2kg/$\textrm{cm}^2$. It has been known that when cement is added to high water content marine clay, its unconfined compression strength increased to 2kg/$\textrm{cm}^2$. Consolidation results show that pre-consolidation pressure increased to 1.8kg/$\textrm{cm}^2$ and 3.4kg/$\textrm{cm}^2$ with the addition of 3% and 5% of cement respectively. This result shows that low-height embankments could be constructed without significant compression. Since the effectiveness of improvement may be different site by site, the mix design for each site is necessary in order to optimize it. The process is first to determine aimed shear strength and then optimum mix ratio of cement after carrying out a series of tests.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2009.09a
• /
• pp.412-419
• /
• 2009

Large quantity of extra soils discharged from excavation site in Songdo area can be treated by hardening agents and utilized in surface stabilized layer overlying thick reclaimed soft soil deposit. Though surface layer stabilization method using cement or lime for very soft soils has been studied in recent years, but studies on moderately soft clayey silt has not been tried. The purpose of this research is to investigate optimum mixing condition for stabilizing Songdo marine soil with low plasiticity. The optimum mixing conditions of hardening agents with Songdo soil such as kind of agents, mixing ratio, initial water content and curing time are investigated by uniaxial compression test and laboratory vane test. The results indicate that strength increases with high mixing ratio and long curing time, while decreases drastically under certain water content before mixing. Finally, optimum mixing condition considering economic efficiency and workability with test results was proposed.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2010.09c
• /
• pp.18-23
• /
• 2010

The estimation of the undrained shear strength $s_u$ for clays using CPT results has been mainly based on the cone factor $N_k$. In this study, a new CPT-based method for the estimation of the undrained shear strength $s_u$ is presented. This aims at reducing uncertainties for the estimation of $s_u$ and enhancing the application of CPT results in more effective manner. For this purpose, a site located at a marine clay deposit is selected and test results from extensive experimental testing program are adopted. The new method defines a direct correlation between the undrained shear strength $s_u$ and the cone resistance $q_t$, excluding the procedure of the overburden pressure correction and therefore undisturbed soil sampling process. In order to verify the new CPT-based method, additional test sites and example sites from literature, which consist of a variety of soil conditions, are selected and examined. It is observed that values of su obtained from the proposed method are in good agreements with measured values of $s_u$ for all the selected verification cases.

• Corrosion Science and Technology
• /
• v.21 no.5
• /
• pp.340-347
• /
• 2022

In this research, mixed metal oxide (TiO₂, RuO₂) coating was applied to grade 1 titanium as a bipolar plate for polymer electrolyte membrane fuel cell (PEMFC). Electrochemical experiments were carried out in an aqueous solution of pH 3 (H₂SO₄ + 0.1 ppm HF, 80 ℃) determined by DoE. The air was bubbled to simulate a cathode environment. Potentiodynamic polarization test revealed that corrosion current densities of the titanium substrate and MMO-coated specimen were 0.180 µA/cm² and 4.381 µA/cm², respectively. There was no active peak. After potentiostatic experiment, current densities of the titanium substrate and the MMO-coated specimen were 0.19 µA/cm² and 1.05 µA/cm², respectively. As a result of observing the surface before and after the potentiostatic experiment, cracked dried clay structures were observed without corrosion damage. Both the titanium substrate and the MMO-coated specimen could not satisfy the interfacial contact resistance suggested by the DoE. Thus, further research is needed before they could be applied as bipolar plates.

• Geomechanics and Engineering
• /
• v.33 no.1
• /
• pp.113-120
• /
• 2023

Coastal and offshore structures such as ports and offshore wind farms will often need to be built on fine-grained sediments. Geotechnical properties associated with sediment compressibility are key parameters for marine construction designs especially on soft grounds, which involve clay-mineral dominated fines that can consolidate and settle significantly in response to engineered and environmental loads. We conduct liquid limit tests and 1D consolidation tests with fine-grained soils (silica silt, mica, kaolin and bentonite) and biogenic soils (diatom). The pore fluids for the liquid limit tests include deionized water and a series of brines with NaCl salt concentrations of 0.001 m, 0.01 m, 0.1 m, 0.6 m and 2.0 m, and the pore fluids for the consolidation tests deionized water, 0.01 m, 0.6 m, 2 m. The salt concentrations help the liquid limits of kaolin and bentonite decrease, but those of diatom slightly increase. The silica silt and mica show minimal changes in liquid limit due to salt concentrations. Accordingly, compression indices of soils follow the trend of the liquid limit as the liquid limit determined the initial void ratio of the consolidation test. Diatoms are more likely to be broken than clastic sediments during to loading, and diatom-rich sediment is therefore generally more compressible than clastic-rich sediment.

• Korean Journal of Soil Science and Fertilizer
• /
• v.2 no.1
• /
• pp.1-13
• /
• 1969

A total of 129 surface(upto 30 cm depth) soil samples were selected from the profile samples collected during reconnaissance soil survey in 1967, for the determination of phosphorus absorption co-efficient. The distribution range for each soil association has been established. The physicochemical factors affecting the phosphorus absorption coefficient have also been examined. The following general conclusions can be drown: 1. In general, the phosphorus absorption coefficient of the soil association of presently arable land are lower than the soils which are not in cultivation. 2. The higher the cation exchange capacity of soils, the higher is the phosphorus absorption coefficient. The factors governing phosphorus absorption coefficient in various soil associations are as follows: Parent Material Soil Association Governing Factor Fluvio marine Low Humic Gley Fluvio marine Alluvial Complex Narrow valley Siliceo mafic materials Red-yellow podzolic Redish Siliceo mafic materials Brown Lateritic Clay content Siliceous crystalline materials Lithosols C.E.C. & Clay content Alluvium Low Humic Alluvium Gley Alluvial Organic matter Siliceous crystalline materials Red-Yellow Podzolic Organic matter and clay content 4. The relation between phosphorus absorption coefficient determined by $(NH_4)_2HPO_4(y)$ and by the P 700 ppm $NaH_2PO_4(x)$ is $Y=2.716X+37(r=0.96^{**})$ which shows highly significant positive correlation and linear regression.