• Journal of Korean Tunnelling and Underground Space Association
• /
• v.18 no.4
• /
• pp.355-364
• /
• 2016

Recently, a 3,250 meter-long tunnel was constructed beneath the sea bed formed of composite sedimentary soils to transport reusable waste heat gas of industrial complex in the west coast of Korea. Some risks such as machine settlement always exist due to the uncertainties of geological and construction factors during the subsea shield TBM tunnelling. In this construction site, the deviation of tunnel alignment caused by shield TBM settlement was occurred during excavation. It was examined that the lack of bearing capacity of soft clay was a main cause. This paper evaluates the risk of shield TBM tunnelling considering the ground conditions. Correlation between machine settlement and its advance rate was evaluated through the analytical equation in which bearing capacity is considered and a 3-D numerical analysis which can simulate the TBM advance condition (in other words, the dynamic condition). It was found out that a shield TBM could settle due to the insufficient bearing capacity of soft clay layers. In order to prevent such the problem, the best advance rate proper to the ground characteristics is needed to be applied. In the ground conditions of the section of interest, it was turned out that if the shield TBM advance rate was maintained between 35 mm/min and 40 mm/min, the machine settlement could be avoided.

• Geotechnical Engineering
• /
• v.9 no.3
• /
• pp.49-60
• /
• 1993

The compatibility of chemicals in the leachates with the three natural and artificially -made liner materials is analyzed by performing the laboratory hydraulic conductivity test. The selected liner materials are natural marine clay, fly ash and weathered granitic soil stomped from Kimpo Wastefills, Seochon power plant and Mansu Dong, Inchon, respectivaly. Bentonites of 20 and 10 percent by weight are used as additive materials for fly ash and weathered granitic soil and the chemical solutions used in the test are acetic acid, methanol, heptane, and aniline which are frequently found in the leachate of waste fills. The concentrations of the chemical solutions are 100% and 75%. The results of the tests show that hydraulic conductivities of the oxter materials are increased by one or two orders of magnitude with permeating pure chemical solutions. The rate of hydraulic conductivity increase is lowest for Seochon fly ash admixed liner and highest for natural marine clay liner. The influence of hydraulic chemical solutions on the liner materials is least for acetic acid and largest for aniline. The increases of conductivity are not shown with the permeation of the solution of concentration 75%. At least by this test results, it can be recognized that the tested liner material can be quite stable with the solutions of significantly high concentration except pure solutions.

• Journal of the Korean Geotechnical Society
• /
• v.16 no.4
• /
• pp.83-94
• /
• 2000

Applicability of PMT in domestic area, test procedure, and methods determining the shear strength parameters $(cu,\phi)$and deformation character (E) using PMT results were studied. At six test boreholes of three construction sites in Pusan, PMT using Elastometer-200 type was performed. The problems occurring during tests were investigated and the test results were analysed.In-situ total horizontal stress could be obtained by observation from pressuremeter curve and limit pressure, ｐ could be determined by $ｐ-log(\Deltav/v)$ method. Shear strength parameters$(cu,\phi)$ and deformation modulus(G, E) could be determined from the PMT results. But effective friction angle and undrained cohesion determined from PMT results were greater than those obtained from laboratory test.Using PMT results, marine soil in Pusan could be classified approximately. Net limite pressure values were in the range of 6.4~22.5 $kg/cm^2$, in clay, 2.2~30.$kg/cm^2$, in sand, 13.0~58.0$kg/cm^2$, in weathered soil and 47.0~190.0 $kg/cm^2$, in weathered rock. Also, Em/ｐ values were in the range of 2.4~7.0 in clay, 2.6~12.1 in sand, 6.8~17.1 in weathered soil and 7.2~29.6 in weathered rock.

• Journal of the Korean GEO-environmental Society
• /
• v.21 no.9
• /
• pp.25-32
• /
• 2020

The underground utilities installed under the ground is an important civil engineering structure, such as water supply and sewerage pipes, underground power lines, various communication lines, and city gas pipes. Such underground utilities can be exposed to risk due to external factors such as concentrated rainfall and vehicle load, and it is important to select and construct an appropriate backfill material. Currently, a method mainly used is to fill the soil around the underground utilities and compact it. But it is difficult to compact the lower part of the buried pipe and the compaction efficiency decreases, reducing the stability of the underground utilities and causing various damages. In addition, there are disadvantages such as a decrease in ground strength due to disturbance of the ground, a complicated construction process, and construction costs increase because the construction period becomes longer, and civil complaints due to traffic restrictions. One way to solve this problem is to use a liquid filler. The liquid filler has advantages such as self-leveling ability, self-compaction, fluidity, artificial strength control, and low strength that can be re-excavated for maintenance. In this study, uniaxial compression strength test and fluidity test were performed to characterize the mixed soil using marine clay, stabilizer, and in-situ soil as backfill material. A freezing-thawing test was performed to understand the strength characteristics of the liquid filler by freezing, and in order to examine the effect of the filling materials on the corrosion of the underground pipe, an electrical resistivity test and a pH test were performed.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.33 no.3
• /
• pp.250-256
• /
• 2000

The purpose of this study was to investigate the adsorption kinetics of heavy metals (Cu, Cd and Pb) using three tidal flat sediments and two yellow loesses. The relationship between adsorption rate calculated by non-linear regression model and chemical parameters was estimated. The contents of ignitiot loss (I.L.) am Fe, Mn and Al oxides of yellow loess were higher $1.5{\~}6 times$ than those of tidal flat sediments. But the contents of silt and clay of tidal flat sediment in Eueunri was higher than others. Heavy metals adsorption were occured rapidly in the intial 30 min and the concentration of adsorbed heavy metals were $4.1{\~}14.7\;{\mu}g/g\;for\;Cu,\;2.8{\~}16.7\;{\mu}g/g\;for\;Cd\;and\;43.4{\~}101.7\;{\mu}g/g$ for Pb, showing a high cumulative adsorption of $8{\~}70{\%}\;for\;Cu,\;18{\~}31{\%}\;for\;Cd and\;19{\~}52{\%}$ for Pb after 3hr. In initial concentration of $0.5{\times}10^(-5)M$, adsorption rate of heavy metals by the tidal flat sediments and yellow loesses was the sequence Pb>Cu^gt;Cd. The adsorption kinetics of Cu, Cd and Pb was found to be one-site kinetic model. Especially, in the case of Cu, there was a high negative ($R^2= -0.88{\~}-0.99$) linear correlation between chemical parameter such as I.L., Al oxide, silt and clay, and adsorption rate coefficients ($K_a$) calculated by non-linear model.

• Journal of the Korean Society for Marine Environment & Energy
• /
• v.13 no.3
• /
• pp.198-205
• /
• 2010

The purpose of this study is to investigate the characteristics of the grain size distribution and organic matters to understand the current status of the tidal flat sediment for efficient management of Suncheon Bay. We investigated the characteristics of the surface sediments in the mouth area of the Suncheon Bay at fifteen stations in April and July, 2009. Specific conclusions were as follows. The sediments in the most part of tidal flat was shown as muddy facies(clay and silt contents was more than 90%), whereas in the tidal river affected by water flow from the Dongstream was shown as sandy facies. The analyzed values of the tidal flat sediment were in the range of $1.9{\sim}3.8{\phi}$(mean $2.5{\phi}$) for sorting, and -1.5~3.2(mean -0.3) for skewness, and 1.5~14.1(mean 3.9) for kurtosis. So we knew that the tidal flat sediments in the Suncheon Bay was mainly composed by fine-grained sediment. Erosion was happened in the tidal river, whereas sedimentation was occurred in the tidal flat. The most of organic matters was derived from the Dongstream. Total organic matters shown as ignition loss was 5.75%, COD and $H_2S$ values were lower than the eutrophication level(COD; 20.0 mg/g dry, $H_2S$; 0.2 mg S/g dry). From our research the tidal flat of the Suncheon Bay is relatively fine, but a part of the flat was exceed the environmental standard. So we have to establish effective countermeasures to reduce the organic matters and nutrients derived from stream for environmental preservation of the Suncheon bay and conduct scientifically sustainable monitering for streams flowing into Suncheon Bay and tidal flat.

• Journal of the Korean GEO-environmental Society
• /
• v.21 no.7
• /
• pp.17-26
• /
• 2020

The soft ground in the southwest coastal area composed of marine clay is greatly influenced by sediment composition, particle size distribution, particle shape, adsorption ions and pore water characteristics, tide and temperature. In addition, the geotechnical properties are very complex due to stress history, change in pore water, dissolution process and gas formation. In this study, the physical and mechanical properties of the soft ground were evaluated through field tests and laboratory tests to investigate the strength increase characteristics according to consolidation on the soft ground in the southwest coast. In addition, in order to understand the consolidation behavior of soft ground such as subsidence, pore water pressure, horizontal displacement of soil by embankment load, measuring instruments such as pore water pressuremeter, settlement gauge, inclinometer and differential settlement gauge was installed, and a piezocon penetration test was carried out step by step to confirm the increase in shear strength of the ground. Through this, it was confirmed that the shear strength of the ground is increased according to the stages of filling. In addition, by evaluating the properties of consolidation behavior, strength increase and consolidation prediction by empirical methods and theories were compared to analyze the characteristics of strength increase rate and consolidation behavior in consideration of regional characteristics.

• Journal of the Korean Geosynthetics Society
• /
• v.13 no.4
• /
• pp.33-43
• /
• 2014

Recently, the case to construct the structure on the soft clayey ground has increased and in order to the reduction of the cost of construction and maintenance on the social infrastructure facilities we have been trying to improve the soft clayey ground using the existing methods such as the pre-loading method and the vertical drain method. Like this, when various ground improvement methods are applied on the soft clayey ground, a long-term consolidation settlement will be key issue due to low permeability coefficient of cohesive soil. According to existing research results that relate to the consolidation settlement, the loading periods for existing the standard consolidation test (Oedometer test) to obtain the consolidation parameters are needed for minimum ten days or more. Therefore, in this study, the standard consolidation test (24 hours step-loading) and constant strain rate consolidation test changed by strain rate was performed using the remolded marine clay on Gwangyang bay composed of a soft clayey ground of the south-west coast. From the laboratory test results, the characteristics of compression, strain-effective stress relations by constant strain rate and the variation characteristic of the pore water pressure by different of loading speed and the relation between consolidation parameters and constant strain rate are compared and analyzed.

• Journal of the Korean Geotechnical Society
• /
• v.24 no.1
• /
• pp.37-49
• /
• 2008

A geothermal heat pump system is a preferable alternative energy system in Korea because it uses the heat energy of the earth, which is environmentally friendly and inexhaustible. In order to characterize the thermal conductivity and viscosity of grout materials used for backfilling ground heat exchangers, nine bentonite grouts, one marine clay from Boryung, and cement grouts adapted in the United State have been considered in this study. The bentonite grouts indicate that the thermal conductivity and viscosity increase with the content of bentonite or filler (silica sand). In addition, material segregation can be observed when the viscosity of grout is relatively low. The marine clay turns out to be unsuitable for backfilling the ground heat exchanger due to its insufficient swelling potential. The saturated cement grouts appear to possess much higher thermal conductivity than the saturated bentonite grouts, and the reduction of thermal conductivity in the cement grouts after drying specimens is less than that in the case of the bentonite grouts. Maintaining the moisture content of grouts is a crucial factor in enhancing the efficiency of ground heat exchangers.

• Journal of the Mineralogical Society of Korea
• /
• v.19 no.3 s.49
• /
• pp.163-169
• /
• 2006

Mineralogy and geochemistry of the sediment core from the seamount (2710 m below the sea level) just south of the Antarctic Polar Front were examined to draw paleoceanographic information in glacial-interglacial cycles. Smectite was most abundant clay mineral associated with illite and chlorite. Its content was slightly higher below 170 cm, suggesting a boundary between isotope stage 4 and 5. Si, Zr, Cs, Th, REE, $K_{2}O$, and $Al_{2}O_{3}$ show complete antithetical distribution with respect to $CaCO_{3}$ through the core. $SiO_{2}$ maxima and $CaCO_{3}$ minima at depths of 24, 136, and 176 cm are probably correlated with massive influx of ice-rafted debris during the advance of Antarctic ice shelves. Ni, Cu, and Ba show rather little correlation with $SiO_{2}$, suggesting their relation to biogenic debris, precipitation from seawater, or hydrothermal input. Particularly, Ba maxima tend to lag $10{\sim}20cm$ after $SiO_{2}$ maxima, probably due to rapid increase of productivity following deglaciation.