• 한국생산제조학회지
• /
• 제8권3호
• /
• pp.66-75
• /
• 1999

This paper is concerned with a analysis of noise by inverse problem available for analyzing the two and three-dimensional acoustic field problems. The noise of analysis considered in this study can be reduced to an optimum problem to find the optimal set of parameters defining the vibrating state of noise source surfaces. The optimal set of parameters are searched by the standard optimization procedure minimizing the square sum of the residuals between the measured and computed quantities of sound pressure at some points in the acoustic field. Computation is carried out for typical examples in which the noise sources are located on the infinite plane. It is demonstrated that the noise of analysis can be effectively made by using the sensitive reference data.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1997년도 추계학술대회 논문집
• /
• pp.989-992
• /
• 1997

The objective of this study is to develop stencil cutting process and determine optimal conditions which make good-quality stencil by using a Nd:YAG laser. The effects of process parameters such as laser power, type of mask, gas pressure, cutting speed and pulse width on the cut edge quality were investigated. In order to analyze the cut surface characteristics(roughness, kerf width, dross) optical microscopy, SEM photography and roughness test were used. A a results, the optimal conditions of process parameters were determined, and the practical feasibility of the proposed system is also examined by using a commercial gerber file for PCB stencil manufacturing.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1997년도 추계학술대회 논문집
• /
• pp.523-526
• /
• 1997

Sheanng is one of the most important operating processes in the field of sheet metal manufacturing. Compared with casting, forging and machining, shearing is very economical to obtain the desired shape. In recent years there has been increasing the use of shearing process in the manufacturing of small and light electronic components. In this paper, it has been researched the experimental investigation to examine the mfl uence of shearing process parameters such as clearance and lower holder configuration. Through the experiment results, the more narrow clearance gives the smaller burr height and the removal of lower holder makes the worse sheared surface. And FE simulation of shearing process using DEFORM-2D were camed out and the results compared w~th experimental studies

• 한국생산제조학회지
• /
• 제5권3호
• /
• pp.58-65
• /
• 1996

This thesis is concerned with the study on the characteristics of the cutting resistance occurring in finish machining of hardened steels such as carbon tool steel and alloy tool steel by a ceramic tool with nose radius. For the purpose, the shape of cutting cross-section made at nose part of the tool was analyzed geometrically and the wear mechanism on the flank face of the ceramic tool is investigated. In order to investigate the characteristics of cutting resistance two categories of cutting conditions are suggested, along with geometrical analysis. One category includes the conventional cutting parameters such as feed and depth of cut, another containing new cutting parameters of thickness of cut and width of cut etc. Thickness of cut width of cut and area of undeformed chip section formed by the condition of engagement between workpiece and cutting tool are determined as the function of feed, depth of cut and nose radius of cutting too, And an effective approach angle is determined by depth of cut and nose radius.

• 한국생산제조학회지
• /
• 제25권3호
• /
• pp.224-229
• /
• 2016

Recently, polymeric micro-fluidic biochips with numerous micro patterns on the surface were fabricated by injection molding for realizing low-cost mass production of devices. To evaluate the effects of process parameters on large-scale micro-structure replication, a $50{\times}50mm^2$ tool insert with surface structures having a patterns of trapezoidal shapes (height: $30{\mu}m$) was employed. During injection molding, PMMA was used; packing phase parameters and mold temperature were investigated. The replicated surface textures were quantitatively characterized by confocal laser microscopy with 10-nm resolution. The degree of replication at low mold temperatures was found to be higher than that at high mold temperature at the beginning of the packing stage. Thereafter, the degree of replication increased to a greater extent at higher mold temperatures; application of higher mold temperatures improved the degree of replication.

• 한국기계가공학회지
• /
• 제4권3호
• /
• pp.20-31
• /
• 2005

The contents of mobile phones are rapidly appended and the structures are being changed substantially. Most of the problems with mobile phones are related with the vibrations and the displacements of PCB boards. In this study, the vibration magnitudes of the boards by impulses on the case are analyzed with the variations of the selected design parameters. The result shows that the extensive suppression of the vibrations are feasible by the proper selection of the design parameters. Also the suggested relationships between the parameter selections and the magnitudes of vibrations can be applied to establish a database for improved stability of the mobile phone structure which is a critical concern considering the short life span of the mobile phone models.

• 한국기계가공학회지
• /
• 제11권4호
• /
• pp.31-38
• /
• 2012

In this paper, we selected primary cutting parameters that influence on surface roughness of cut bottom surface in end-milling for SM25C material. Those are overhang, depth of cut, feed rate and spindle speed. And then performed orthogonal array experiment and ANOVA by Taguchi method to determine that improved level combination of cutting parameters for betterment of working efficiency and surface roughness one of quality characteristics. And we verified a advisability of prediction model by verification test about level combination. From the results, main cutting parameter influences on surface roughness is spindle speed and the next is feed rate.

• 한국기계가공학회지
• /
• 제12권1호
• /
• pp.22-27
• /
• 2013

A shot blasting process is to improve the surface quality of stainless steels. The process is similar to a well-known shot peening that is used to strengthen the surface via the residual stress. In the shot blasting process, it is important to decide many parameters, such as the size, incident angle and velocity of shot balls, to effectively get rid of the iron oxide on the surface of stainless steels. In this study, the simulation of the shot blasting process is carried out by a finite element software, which can help to find out the optimal design parameters to cause the delamination of the iron oxide from the stainless steel substrate. The results obtained are also compared to those of the discrete element method to verify them.

• Transactions on Electrical and Electronic Materials
• /
• 제7권2호
• /
• pp.62-66
• /
• 2006

Advanced CMP conditioner design requires investigations of key conditioner manufacturing parameters and their effects on pad surface and then wafer performance. In the present investigation, diamond shape, concentration, distribution, and other key manufacturing parameters are considered to improve CMP process stability and conditioner life. Self avoiding random distribution ($SARD^{TM}$) of diamond abrasives has been developed and both numerical simulation and experimental results show very stable and reliable polishing performance.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2004년도 추계학술대회논문집
• /
• pp.19-22
• /
• 2004

Shearing including punching, blanking, trimming, slitting, etc is one of the most frequently used processes in sheet metal manufacturing. It has been widely using for manufacturing autobody, electronic components, aircraftbody, etc. In this paper, it has been researched by the experimental investigation to examine the influence of shearing processes parameters such as clearance, cutting angle, material properties, etc. From the results of experiment, it has shown that it gives the small variations at burr height below the proper clearance and it also presents that it is no affected the variations of cutting angle.