• 한국소음진동공학회논문집
• /
• 제18권8호
• /
• pp.816-822
• /
• 2008

This study presents the design modification for SCR muffler of a commercial vehicle. Its main objective is the reduction of radiated noise at SCR muffler. For this study, the research of five steps were achieved by experimental and CAE analysis. First step is the measurement of radiated noise using impact-acoustic test. Second step is the source identification using experimental modal analysis. The cause of radiated noise source is confirmed by the resonance of end plates at SCR muffler. Third step confirms the possibility of resonance avoidance using SDM analysis applied the mass control. Fourth step is the suggestion of design modification which is the change of mode shape by CAE analysis. Last step is the verification of design modification using SYSNOISE analysis. Finally, the prototype product applied the countermeasure of resonance evasion was manufactured and the reduction of radiated noise at SCR muffler was confirmed by pass-by noise test.

• 소음진동
• /
• 제9권2호
• /
• pp.310-316
• /
• 1999

4-Pole parameter method based on an acoustic theory is very popular for the analysis of the acoustic behavior of the car exhaust system. However, this method is applicable only for the simple shape of acoustic elements of the muffler. Numerical methods such as FEM(Finite Element Method) or BEM(Boundary Element Method) can also provide acceptable results for the acoustic analysis of the car exhaust system. Even though these numerical methods have benefits for the analysis of complicated shape of acoustic elements of the muffler, time consuming is another problem during modeling and numerical calculation. Combining benefits of both methods, the new code called the hybrid method for car exhaust system is introduced. And the developed code is utilized for calculation of the transmission loss of a main muffler of an automobile comparing with the experimental results.

• Journal of Welding and Joining
• /
• 제33권2호
• /
• pp.23-31
• /
• 2015

Stainless steel is used in automobile muffler and exhaust systems. However, in comparison with other steels it has a high thermal expansion rate and low thermal conductivity, and undergoes excessive thermal deformation after welding. To address this problem, we evaluated the use of arc brazing in place of welding for the processing of an exhaust system, and investigated the parameters that affect the joint characteristics. Muffler parts STS439 and hot-dipped Al coated steel were used as test specimens, and CuAl brazing wire was used as the filler metal for the cold metal transfer (CMT) welding machine, which is a low heat input arc welder. In addition, a Box-Behnken design of experiment was used, which is a response surface methodology. The main process parameters (current, speed, and torch angle) were used to determine the appropriate welding quality and the mechanical properties of the brazing part was evaluated at the optimal welding condition. The optimal processing condition for arc brazing was 135A current, 51cm/min speed and $74^{\circ}$ torch angle. The process was applied to an actual exhaust system muffler and the prototype was validated by thermal fatigue, thermal shock, and endurance limit tests.

• 품질경영학회지
• /
• 제30권1호
• /
• pp.133-143
• /
• 2002

We propose an optimal design to improve the muffler's capacity by reducing the noise of the intake system by adapting kriging method with the robust design. For the first stage of a design, the length and radius of each component of the current muffler system are selected as control factors. Then, the $L_18$ table of orthogonal arrays is adapted to extract the effective main factors. As the second stage, the $L_18$ table of orthogonal arrays using kriging method is adapted to take the significant factors into consideration. As an optimal design, the $L_18$ table of orthogonal arrays with main effects is proposed and the kriging method is adapted for more efficient design. The kriging method improves the performance of intake system.

• 한국레이저가공학회지
• /
• 제17권2호
• /
• pp.11-18
• /
• 2014

This research was conducted as a fundamental study to apply tailored blank welding technique into automotive production process. Specially we tried to apply the TWB technique to exhaust system. The materials used in this work were ferritic 439 stainless steel sheet with a thickness of 1.2mm and 0.8mm. Welding tests were conducted for BOP test and dissimilar thickness (0.8 to 1.2t) cases. Major process parameters were position of focus, travel speed, shielding gas and joint (gap) condition. As a result, there are nothing significant welding characteristic compare with TWB of carbon steel. Stainless steel shows the good weldability and mechanical properties (tensile, hardness and forming strength) also shows high level. Just problem is gap condition. However, also in this case, it shows not only good forming strength but also base metal fracture after tensile test. And to conclude, it is good opportunity to make lightweight design muffler using TB welding technique.

• 소음진동
• /
• 제11권3호
• /
• pp.401-409
• /
• 2001

Passive type mufflers installed on every car haute inherent problem of lowering engine power and fuel efficiency caused by backpressure which is byproduct of complex internal structure. Recent improvements like installing a calve to change exhaust gas path depending on power requirement and rpm have only marginally improved performance. Tremendous amount of recent research works on active exhaust noise control have failed to commercialize because of numerous physical and economical reasons. In this paper, a unique seal-active muffler using difference of transmission paths is presented. In this system exhaust pipe is divided into two and joined again downstream. Exhaust noise is reduced by destructive interference when two-divided noise join again with transmission paths'difference which is half of the wavelength of a main noise frequency. One divided path has a sliding mechanism to change length thereby transmission path length difference is adjusted to entwine rpm change. The proposed system has minimal backpressure and does not need a secondary sound source like a speaker so it can overcome many problems of failed active noise control methods. We have verified proposed system's superior performance by simulation and comparison experiment with passive mufflers.

• 한국자동차공학회논문집
• /
• 제21권4호
• /
• pp.23-32
• /
• 2013

This paper presents the simulation of the multi-cylinder 4-stroke cycle spark-ignition engine using a commercial simulation tool, AVL BOOST. Various models were examined to select the appropriate models that would best serve to analyze the main components of the intake and exhaust systems-the plenum chamber, the muffler and the exhaust manifold branch junction. For the plenum chamber and the muffler, the tank model and the pipe model were tested. In order to analyze the exhaust manifold branch junction, a complicated model which reflects the actual shape and involves pressure drops was compared to a simplified one. The results show that both the tank model and the pipe model are applicable with satisfying accuracies for the plenum chamber and the muffler. However, the tank model is more desirable in regards to convenience in modeling and efficiency in calculation. Though both the complicated model and the simplified model show satisfying accuracies for the exhaust manifold branch junction, the simplified model is recommended in regards to convenience in modeling and efficiency in calculation.

• 한국음향학회:학술대회논문집
• /
• 한국음향학회 1994년도 FIFTH WESTERN PACIFIC REGIONAL ACOUSTICS CONFERENCE SEOUL KOREA
• /
• pp.860-863
• /
• 1994

Main sources of increased vibrations and air noise on ship are main and auxiliary engines and ship ducts. The various ways of transfer of vibration energy and air noise in passenger cabin of a vessel require, in general case, of various methods of attenuation. The transfer of vibration energy from engines through a support requires, alongside with shock-absorbers, availability active shock-absorbers. The transfer of vibration energy and hydrodynamic noise on ship ducts requires availability, alongside with flexible muffler, active mufflers. The availability of air noise from working equipment can require, along with absorbent covers, of space systems of active noise control. In the given article it is spoken about the unified approach to formation of the block-diagram of active noise and vibration control. The complex approach permits to receive additional efficiency in reduction of noise in passenger cabin of vessels.

• 한국의류산업학회지
• /
• 제1권3호
• /
• pp.231-238
• /
• 1999

The purpose of this study was to identify characteristics and consumer attitude on purchasing apparel of Cable TV home-shopping viewer: A questionnaire was developed to measure watching attributes, consumers' attitude and actual purchasing condition of Cable TV home shopping, and demographic variables. The questionnaire was administered to 277 adult, and the data were analyzed by using frequency; crosstab, t-test, ANOVA. The results of this study were as follows: 1. main view time were 3~5 p.m. 11 p.m, 10~12 a.m. home shopping through Cable Tv. Women's main terms were afternoon, whereas men's main terms were night. Chiefly view program was about apparel and fashion items. The reason why they watched the home-shopping channel was to purchase more cheaper items. 2. Favor about Cable TV home-shopping was relatively affirmative, but purchasing intention through home-shopping was still negative. But affirmative response was gradually increasing a few years ago. 3. Purchasing experience through Cable TV home shopping was 61.0% and clothing purchaser within recently 6 months was 28.5% of total sample. Withspreading Cable TV widely; Cable TV home shopper was gradually increasing. Heavy purchasing items through Cable TV home-shopping were under-wear; muffler, shawl, because those items are standardized in size and style. When home shopping user made purchasing decision, the most significant factors were color; and size (fit), price in order of importance.

• International Journal of Naval Architecture and Ocean Engineering
• /
• 제6권4호
• /
• pp.935-946
• /
• 2014

This paper investigates the noise transmission performance of industrial mufflers widely used in ships based on the CAE modeling and simulation. Since the industrial mufflers have very complicated internal structures, the conventional Transfer Matrix Method (TMM) is of limited use. The CAE modeling and simulation is therefore required to incorporate commercial softwares: CATIA for geometry modeling, MSC/PATRAN for FE meshing and LMS/SYSNOISE for analysis. Main sources of difficulties in this study are led by complicated arrangement of reactive elements, perforated walls and absorption materials. The reactive elements and absorbent materials are modeled by applying boundary conditions given by impedance. The perforated walls are modeled by applying the transfer impedance on the duplicated node mesh. The CAE approach presented in this paper is verified by comparing with the theoretical solution of a concentric-tube resonator and is applied for industrial mufflers.