• 한국CDE학회논문집
• /
• 제17권1호
• /
• pp.1-6
• /
• 2012

The End Coupling is main component of the aluminum hot roll process. The End Coupling is used for transmission of rotational power with heavy-duty load. Fracture of the End Coupling cause serious economic losses because an End Coupling is a very expensive component and it takes a long time to repair it. Therefore, preventing the destruction of the End Coupling is essential for ensuring a long mechanical life cycle. In this paper, the parametric study on the End Coupling was performed in order to minimize maximum stress under operation loads. To verify the interference of spindle assembly with modified End Coupling, kinematics simulation was performed by applying the various combination type and dynamic boundary condition of the spindle assembly. The interference of optimized model was not occurred during combination process and driving process. As a result of an optimum design for life extension on End Coupling, the maximum stress of modified End Coupling was lower than that of the initial model by 26%.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2000년도 춘계학술대회논문집 - 한국공작기계학회
• /
• pp.697-703
• /
• 2000

In design step of an active vibration control system, the stability analysis is required for obtaining a stable control region so that the system is protected from it violent natural vibration. This paper describes the procedure of stability simulation for the active magnetic bearing-main spindle of a machine tool. The characteristic equation of the overall system is derived by assembling the dynamic equation of a flexible shaft and the transfer functions of feedback components. And the stable region is obtained by calculating the eigenvalues of the characteristic equation. The simulated control stable region is good agreement by comparing the experiment. Therefore the stable control gain is selected in this paper.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1996년도 춘계학술대회 논문집
• /
• pp.330-335
• /
• 1996

The well-conditioned observer design method is extended for two-output systems where observer gains are not determined uniquely with respect to the desired observer poles. Similar to the previous results, this design method makes off-diagonal elements of the observer upper-left submatrix skew-symmetric and simulataneously, places the eigenvalues of the observer matrix widely separated by selecting upper two rows of the observer gain. The proposed design method is evaluated in a spindle-drive example where the load speed is estimated based on motor speed and the armature current.

• 한국기계가공학회지
• /
• 제11권4호
• /
• pp.31-38
• /
• 2012

In this paper, we selected primary cutting parameters that influence on surface roughness of cut bottom surface in end-milling for SM25C material. Those are overhang, depth of cut, feed rate and spindle speed. And then performed orthogonal array experiment and ANOVA by Taguchi method to determine that improved level combination of cutting parameters for betterment of working efficiency and surface roughness one of quality characteristics. And we verified a advisability of prediction model by verification test about level combination. From the results, main cutting parameter influences on surface roughness is spindle speed and the next is feed rate.

• Tribology and Lubricants
• /
• 제7권1호
• /
• pp.35-39
• /
• 1991

The performance of the ultra-precision machine tools depends on the steady state characteristics of the main spindle bearings. For excluding the effect of machining error with perpendicularity, conical or spherical bearing has been used. In this paper, steady analysis of the externally pressurized conical gas bearing for ultraprecision is carried out based on the direct numerical method with assumption of point source. As a result of theoretical analysis, design parameters for optimal condition of conical gas bearing are' presented in dimensionless form.

• Tribology and Lubricants
• /
• 제8권1호
• /
• pp.78-83
• /
• 1992

For excluding the effect of machining error such as perpendicularity, conical and spherical bearing has been used. In this paper, dynamic characteristics of the externally pressurized conical gas bearing for untraprecision main spindle is carried out based on the direct numerical method with assumption of point source. As a result of theoretical analysis, it is verified that coupled stiffness and damping exist and new design parameters for optimal condition of conical gas bearing are presented in dimensionless form.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2003년도 춘계학술대회 논문집
• /
• pp.105-110
• /
• 2003

The hydraulic excavator has been a popular research object for automation because of its multi-workings and economic efficiency. When it works crane tasks, most of disasters happen. The objective of this paper is to design each components and to construct boom, arm, bucket circuit. These models modeled with AMESim show us change of variables and behavior of excavator. Simulation model will be used for simulator of excavator.

• 한국정밀공학회지
• /
• 제28권10호
• /
• pp.1159-1165
• /
• 2011

The recording density of HDD is increasing in ratio of 100% each year. Because the increasing of recording density requires the feature of high rotation, fixation and low-noise, fluid hydrodynamic bearing(FDB) has been paid attention to overcome a limitation in ball bearing. Most of researches related to improving performance of FDB have been studied in Japan which has 80% more market share of HDD spindle motor assembly. Main subject of studies are about for the design of the groove shape, manufacturing process of fluid dynamic bearing, performance evaluation and measurement. In HDD, non-repeatable runout(NRRO) is most important parameter which determines the performance of HDD spindle system because NRRO is unpredictable that cannot be compensated in head/slider servo system. In this study, performance evaluation system can measure dynamic behaviors were designed and methodology for calculating imbalance, RRO, and NRRO were proposed.

• 소성∙가공
• /
• 제12권1호
• /
• pp.18-25
• /
• 2003

This paper explains the process design for improving tool life in the conventional hot forging process. The thermal load and the thermal softening are happened by contact between the hotter billet and the cooler tools in hot forging process. Tool life decreases considerably due to the softening of the surface layer of a tool was caused by a high thermal load and long contact time between the tools and the billet. Also, tool life is to a large extent limited by wear, heat crack and plastic deformation in hot forging process. Above all, the main factors which affect die accuracy and tool life we wear and the plastic deformation of a tool. The newly developed techniques for predicting tool life are applied to estimate the production quantity for a spindle component and these techniques can be applied to improve the tool life in hot forging process.

• 한국공작기계학회논문집
• /
• 제16권4호
• /
• pp.113-118
• /
• 2007

The flow forming has been used to produce long thin walled tube parts, with the reduced fanning force and the enhanced mechanical and surface quality for a good finished part, compared with the fanned parts using other method. Therefore, flow fanning technique is used widely in industrial production. Spinning and flow fanning techniques are used frequently in automotive, aerial and defense industries. The main factors for the flow fanning machine design are motor power, bed rigidity, mandrel stiffness, spindle power, roller profile, etc. Especially, mandrel, spindle power and roller are important factors for flow fanning machine capacity. In this paper, three dimensional finite element method for analysis of one-roller backward flow fanning of a workpiece has been carried out to study effects of roller profile on fanning force. Applied roller profile have roller lead geometries of angle $20^{\circ},\;30^{\circ},\;40^{\circ}$, concave and convex. Axial and radial fanning forces on various roller profiles are obtained and compared with each analysis cases.