• 한국식품과학회지
• /
• 제8권3호
• /
• pp.141-146
• /
• 1976

1) 조효소액(粗酵素液)을 유안염석(硫安鹽析)(0.5포화도(飽和度)) Sephadex G 25에 의(依)한 제염(除鹽), CM Cellulose column chromatography, Sephadex G 25에 의(依)한 농축(濃縮), Sephadex G 75 gel filtration에 의(依)하여 Specific activity 126.5/mg protein, 원활성(原活性)의 약(約) 45배(倍), 수율(收率) 4.2%의 정제효소(精製酵素)를 얻었다. 2) 정제효소(精製酵素)를 Acrylamide gel disc electrophoresis에 의(依)하여 분리(分離)시킨 결과(結果) 하나의 주(主)된 band와 그 양측(兩側)에 2개(個)의 희미한 band가 나타나 있으므로 하나의 순수(純粹)한 단백질(蛋白質)이라고는 할 수 없으나 조효소액(粗酵素液)에 비(比)하여 상당(相當)히 정제(精製)되었다.

• 대한방사선기술학회지:방사선기술과학
• /
• 제16권1호
• /
• pp.107-115
• /
• 1993

In this study, to develop highly sensitive radiation sensors, $CaSO_4$ : Tm phosphors and its disc-type TLD elements embedded PTFE(polytetrafluoroethylene) are fabricated. The highest sensitivity of $CaSO_4$ : Tm phosphors is obtained when phosphors have been doped with 0.5mol % Tm and sintered in atmosphere at $600^{\circ}C$ for two hours. Fabricated disc-type elements are made from a homogeneous mixture of phosphors and PTFE powder. They are first cold-pressed and then polymerized at $370^{\circ}C$ in air for one hour. The dose dependence of the prepared $CaSO_4$ : Tm TLD radiation sensors is linear within the range of $100{\mu}Gy{\sim}10Gy$ for X-rays and ${\gamma}-rays$. The response of $CaSO_4$ : Tm to 30keV X-rays is ten times higher than that of 1.25MeV $^{60}Co\;{\gamma}-rays$. The fading rate of the main peak is about 2% per a month. The spectral peaks of TL emission spectrum are at about 350nm and 475nm. The $CaSO_4$ : Tm TLD radiation sensors prepared in this work may be used as radiation dosimeter for personal and environmental monitoring because of their high sensitivity and little fading.

• The Korean Journal of Pain
• /
• 제21권1호
• /
• pp.74-79
• /
• 2008

The progression of spinal tuberculosis is usually slow and insidious, and its main symptom, backache, is nonspecific. Considerable delay in diagnosis may occur before an infectious process is considered. Even when a diagnosis of spinal tuberculosis is considered, it may be difficult to confirm. Radiological findings indicative of tuberculosis are involvement of the vertebral bodies on either side of the disc, subligamentous spread, abscess formation and collection and expansion of granulation tissue adjacent to the vertebral body, relative sparing of the disc space and calcification within a paravertebral abscess. We report two patients with spinal tuberculosis who had nonspecific backache and received a delayed diagnosis for several months or years.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2002년도 ITC-CSCC -2
• /
• pp.1296-1299
• /
• 2002

We implemented a CD signal processor operated on a CAV 48-speed CD-ROM drive into a VLSI. The CD signal processor is a mixed mode monolithic IC including servo-processor, data recovery, data-processor, and I-bit DAC. For servo signal processing, we included a DSP core, while, for CAV mode playback, we adopted a PLL with a wide recovery range. Data processor (DP) was designed to meet the yellow book specification.［2］So, the DP block consists of EFM demodulator, C1/C2 ECC block, audio processor and a block transferring data to an ATAPI chip. A modified Euclid's algorithm was used as a key equation solver for the ECC block To achieve the high-speed decoding, the RS decoder is operated by a pipelined method. Audio playability is increased by playing a CD-DA disc at the speed of 12X or 16X. For this, subcode sync and data are processed in the same way as main data processing. The overall performance of IC is verified by measuring a transfer rate from the innermost area of disc to the outermost area. At 48-speed, the operating frequency is 210 ㎒, and this chip is fabricated by 0.35 um STD90 cell library of Samsung Electronics.

• 한국전산유체공학회지
• /
• 제17권1호
• /
• pp.61-69
• /
• 2012

In this paper, the shape design process is briefly discussed emphasizing the use of topology optimization in the conceptual design stage. The basic idea is to view feasible domains for sensitivity region concepts. In this method, the main process consists of two steps: as the design moves further inside the feasible domain using Taguchi method, and thus becoming more successful topology optimization, the sensitivity region becomes larger. In designing a double-eccentric butterfly valve, related to hydrodynamic performance and disc structure, are discussed where the use of topology optimization has proven to dramatically improve an existing design and significantly decrease the development time of a shape design. CFD analysis results demonstrate the validity of this approach.

• 정보저장시스템학회논문집
• /
• 제2권3호
• /
• pp.163-168
• /
• 2006

Small form factor optical pickup (SFFOP) corresponding to BD specifications is strongly proposed for the next-generation portable storage device. In order to generate SFFOP, small sized optical pickup has been fabricated. We have developed a small sited optical pickup that is called the integrated optical pickup (IOP). The fabrication method of this system is mainly dependant on the use of the wafer based micro fabrication technology, which has been used in MEMS process such as photolithography, reactive ion etching, wafer bonding, and packaging process. This approach has the merits for mass production and high assembling accuracy. In this study, to generate the small sized optical pickup for high recording capacity, IOP corresponding to BD specifications has been designed and developed, including three main parts, 1) design, fabrication and evaluation of objective lens unit, 2) design and fabrication of IOP and 3) evaluation process of FES and TES.

• 대한산업공학회지
• /
• 제21권4호
• /
• pp.581-591
• /
• 1995

The main objective of this study is to compare three representative methods predicting compressive forces on lumbosacral disc : LP-based method, double LP-based method and EMG-assisted method. Two subjects simulated lifting tasks performed in the refractories industry, in which vertical and horizontal distance, and weight of load were varied. To calculate the L5/S1 compressive forces, EMG signals from six trunk muscles were measured and postural data and locations of load were recorded using the Motion Analysis System. The EMG-assisted model was shown to reflect well all three factors considered here. On the other hand, the compressive forces of the LP-based model and the double LP-based model were only significantly affected by weight of load. In addition, lowly positive correlation was observed between compressive forces of the EMG-assisted model and lifting index(LI) of 1991 NIOSH lifting equation. From this results, it can be concluded that compressive forces on L5/S1 by the EMG-assisted method should be used as biomechanical criterion in order to evaluate risk of jobs precisely, and LI can not evaluate risk of lifting tasks fully.

• 소성∙가공
• /
• 제33권2호
• /
• pp.112-117
• /
• 2024

In this study, the friction and wear characteristics of Inconel 600 in the superplastic forming process of Ti6Al4V were evaluated through pin-on-disc tests. To achieve an efficient and systematic experimental design, the Taguchi method was employed. The wear track of the Inconel 600 pin showed scratches in the sliding contact direction, confirming that the wear mechanism is abrasive wear. Through sensitivity analysis such as ANOVA and Main effects, it was confirmed that both normal force and sliding distance have a significant impact on the wear. Changes in sliding velocity and distance did not affect the friction coefficient, which remained relatively constant at approximately 0.380. The wear prediction model for Inconel 600 in the superplastic forming of Ti6Al4V was constructed, which can be utilized as a guideline for the prediction and management of tool wear.

• 한국항공우주학회지
• /
• 제38권6호
• /
• pp.519-529
• /
• 2010

본 연구에서는 주로터, 동체, 그리고 꼬리로터를 포함한 UH-60A 전기체 형상에 대한 비정상 유동 해석을 수행하였다. 개발된 로터해석용 유동 해석코드를 이용하여 고속 전진 비행 및 저속 전진비행 조건에 대한 해석을 수행하였으며, 해석코드의 검증을 위해 주로터에서의 비정상 공력 하중을 비행시험 및 타 연구자들의 해석 결과와 비교하였다. 주로터만 존재하는 형상, 주로터와 동체만 존재하는 형상, 그리고 꼬리로터만 존재하는 형상에 대한 해석 결과를 전기체 형상에 대한 해석 결과와 비교함으로써 헬리콥터 각 컴포넌트 간의 공기력 간섭현상을 분석하였다. 동체는 주로터에서 발생하는 내리흐름 분포를 변화시킴으로써 주로터의 수직력 분포를 변화시키는 요인이 됨을 확인하였으며, 주로터 끝단으로부터 발생한 와류와 꼬리로터 블레이드가 충돌함에 따라 강한 간섭현상이 발생함을 확인하였다

• 대한물리치료과학회지
• /
• 제3권4호
• /
• pp.207-214
• /
• 1996

Main cause of low back pain is a poor posture. Most low back pains are due to a poor posture. The poor posture induces muscle tension and finaliy low back pain. The poor posture arehabitually trained from the childhood by the environmetal factors. In general, maintaining good posture during working and sleeping hours are the first line of defence against back pam. (1) Supine posture is the easiest posture that relaxes and fixes muscles. Supine posture is thus a starting position for on exercise. Lying down releases the weight pressures of head and shoulder and thus body can be relaxed and extended which are helpful for treating back pain. However, supine posture can increase the pressure in ribcage posture aspect and disphragram due to visceral oragans. (2) Sitting in one position for a long time results in fatigue and relaxation of spinal muscies. Finally, body strength is weakened and sitting posture will become poor. If this poor posture continues for a longer time, pain will be accompanied due to overelongation of muscle ligaments. The habitual poor posture could induce intervertebral disc distortion. If the intervertebral disc is damaged, sitting in one position or movement causes pain. (3) Abnormal lumbar curve induces the tention of abdominal muscle and paravertebral muscle groups as well as tention of lower limb muscle group connected to pelvis. For a person with weak body strength, muscle relaxation increases curvature in lumbar, chest and cervical regions. This will induce a pelvic anterior tilting of the imaginary line between A. S. I. S. and P. S. I. S. Hip joint extensor muscle acts on releasing the pelvic anterior tilting. Contrections of hamstring muscle and femoral muscle recover the imaginary line between A.S.LS. and P.S.I.S. from pelvic anterior tilting. thus, contraction of rectus abdominis muscle are required to maintain the normal lumbar curve.