• Journal of Powder Materials
• /
• v.12 no.1
• /
• pp.24-29
• /
• 2005

Nano Fe-6.5wt%Si powders have been synthesized by mechano-chemical process (MCP) for an application of soft magnetic core. Owing to hard and brittle characteristics of Fe-6.5Si nano powders having large surface area, it is very difficult to reach high density more than 70% of theoretical density (~7.4 g/$cm_3$) by cold compaction. To overcome such problem a magnetic pulsed compaction (MPC), which is one of dynamic compaction techniques, was applied. The green density was achieved about 78% (~5.8 g/$cm_3$) by MPC at room temperature.

• Korean Journal of Materials Research
• /
• v.18 no.8
• /
• pp.411-416
• /
• 2008

In this research, fine-structure TiO2 bulks were fabricated in a combined application of magnetic pulsed compaction (MPC) and subsequent sintering and their densification behavior was investigated. The obtained density of $TiO_2$ bulk prepared via the combined processes increased as the MPC pressure increased from 0.3 to 0.7 GPa. Relatively higher density (88%) in the MPCed specimen at 0.7 GPa was attributed to the decrease of the inter-particle distance of the pre-compacted component. High pressure and rapid compaction using magnetic pulsed compaction reduced the shrinkage rate (about 10% in this case) of the sintered bulks compared to general processing (about 20%). The mixing conditions of PVA, water, and $TiO_2$ nano powder for the compaction of $TiO_2$ nano powder did not affect the density and shrinkage of the sintered bulks due to the high pressure of the MPC.

• Journal of Magnetics
• /
• v.15 no.4
• /
• pp.209-212
• /
• 2010

Photoplethysmogram (PPG) and pressure pulse waveform (PPW) were compared and evaluated for the efficacy of stimulating knuckles by using the pulsed magnetic field. Both signals were observed simultaneously while the knuckles were exposed for 10 min to the pulsed magnetic field, with maximum field intensity of 0.8 T and transition time of 0.126 msec. After 5 min stimulation of the knuckles, the results showed that the aging indexes calculated from the second derivative of the PPG were increased from -1.913 to 0.072, and that of the PPW from -0.063 to 0.387. However, for the relatively long-term stimulation for 10 min, we found that the values of both the aging indexes of the second derivatives and augmentation index of the PPW returned to the starting level. The changes observed in characteristic factors such as the aging indexes of the second derivatives and augmentation index of the PPW indicate the potential of pulsed magnetic field stimulation as a therapeutic method for the treatment of patients with peripheral vascular disease.

• Journal of Powder Materials
• /
• v.15 no.1
• /
• pp.37-45
• /
• 2008

This article presents the challenges toward the successful consolidation of $Al_2O_3$ nanopowder using magnetic pulsed compaction (MPC). In this research the ultrafine-structured $Al_2O_3$ bulks have been fabricated by the combined application of magnetic pulsed compaction (MPC) and subsequent sintering, and their properties were investigated. The obtained density of $Al_2O_3$ bulk prepared by the combined processes was increased with increasing MPC pressure from 0.5 to 1.25 GPa. Relatively higher hardness and fracture toughness in the MPCed specimen at 1.25 GPa were attributed to the retention of the nanostructure in the consolidated bulk without cracks. The higher fracture toughness could be attributed to the crack deflection by homogeneous distribution and the retention of nanostructure, regardless of the presence of porosities. In addition, the as consolidated $Al_2O_3$ bulk using magnetic pulsed compaction showed enhanced breakdown voltage.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2008.10a
• /
• pp.394-397
• /
• 2008

In this research, the fine-structure TiO2+Ti bulks have been fabricated by the combined application of magnetic pulsed compaction (MPC) and subsequent sintering, and their densification behavior was investigated. The obtained density of $TiO_2$+Ti bulk prepared by the combined processes was increased with increasing MPC pressure from 0.7 to 1.7 GPa. Relatively higher density (88%) in the MPCed specimen at 0.7Gpa was attributed to the decreasing of the inter-particle distance of pre-compacted component. High pressure and rapid compaction by Magnetic Pulsed Compaction could reduce shrinkage rate (about 10%) of the sintered bulks compared to that of general processing (about 20%). Mixing conditions of PVA, water, Ti and $TiO_2$ nano powder for compaction of $TiO_2$ nano powder did not affect on density and shrinkage of the sintered bulks due to high pressure of MPC.

• Journal of Magnetics
• /
• v.5 no.4
• /
• pp.124-129
• /
• 2000

$Sm_2Fe_{17}N_x$ film magnets were prepared using a $Sm_2Fe_{17}$ target in a $N_2$ gas atmosphere using a Nd-YAG pulsed laser ablation technique. The effect of nitrogen pressure, deposition temperature, pulse time and film thickness on the structure and magnetic properties of $Sm_2Fe_{17}N_x$ film were studied. Increasing the nitrogen pressure up to 5 atm led to the formation of complete $Sm_2Fe_{17}N_x$ compound. Optimized magnetic properties with the nitrogenation temperature in the range 500-53$0^{\circ}C$ could be obtained by extending the nitrogenation time up to 4 hours. Relatively low coercivities of 400~600 Oe were found in $Sm_2Fe_{17}N_x$films 50~100 m thick, while a $4\piM_s$ of 10$\sim$12 kG could be achieved. In-plane anisotropy, which was the basic goal in this study, was achieved by controlling the nitrogenation parameters.

• Journal of Powder Materials
• /
• v.19 no.5
• /
• pp.373-378
• /
• 2012

Sintered bulks of $ZrO_2$ nanopowders were fabricated by magnetic pulsed compaction (MPC) and subsequent two-step sintering employed in this study and the formability effects of nanopowder on mixing condition, pressure and sintering temperature were investigated. The addition of PVA induced and increase in the formability of the sintered bulk. But cracked bulks were obtained on sintering with addition of over 10 wt% PVA due to generation of crack during sintering. The optimum compaction pressure during MPC was 1.0 GPa and mixing conditions included using 5.0 wt% PVA. The optimum processing condition included MPC process, followed by two-step sintering (first at 1000 and then at $1450^{\circ}C$). The sintered bulks with the diameter of 30 mm under these conditions were found to have non crack, ~99% density.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2011.05a
• /
• pp.58.1-58.1
• /
• 2011

WC-Co and other similar cemented carbides have been widely used as hard materials in industrial cutting tools and as mould metals; and a number of techniques have been applied to improve its microstructural characteristics, hardness and ear resistance. Cobalt is used primarily to facilitate liquid phase sintering and acts as a matrix, i.e. a cementing phase between WC grains. A uniform distribution of metal phase in a ceramic is beneficial for improved mechanical properties of the composite. WC-Co, starting from initial powders, is vastly used for a variety of machining, cutting, drilling, and other applications because of its unique combination of high strength, high hardness, high toughness, and moderate modulus of elasticity, especially with fine grained WC and finely distributed cobalt. In this study, that started with two different compositions of initial powders, WC-7.5wt%Co and WC-12wt%Co with initial powder size being 1~3 ${\mu}m$, magnetic pulsed compaction followed by subsequent vacuum sintering were carried out to produce consolidated preforms. Magnetic Pulsed Compaction (MPC), a very short duration (~600 ${\mu}s$), high pressure (~4 Gpa), high-density preform molding method was used with varied pressure between 0.5 and 3.0 Gpa, in order to reach an initial high density that would help improve the sintering behavior. For both compositions and varied MPC pressure, before and after sintering, changes in microstructural behavior and mechanical properties were analyzed. With proper combination of MPC pressure and sintering, samples were obtained with better mechanical properties, densification and microstructural behavior, and considerably improved than other conventional processes.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2003.03a
• /
• pp.153-153
• /
• 2003

• The Journal of Korean Physical Therapy
• /
• v.26 no.6
• /
• pp.379-385
• /
• 2014

Purpose: This study was to determine the immediate effects of pulsed magnetic field (PMF) in subjects with upper trapezius (UT) trigger point (TrP). Methods: Fifteen subjects with UT TrP were recruited for the study's PMF group (pain threshold=$2.29kg/cm^2$), and 15 age-, weight-, and gender-matched subjects with UT TrP were recruited for control group (pain threshold=$2.25kg/cm^2$). Pressure algometer was used to measure pressure pain threshold on UT TrP and, cervical range of motion (ROM) inclinometer was used to measure cervical ROM. Surface electromyography was used to record UT, lower trapezius, and serratus anterior muscle activity and relative ratio during scapular plane abduction between pre- and post-treatment. Results: The PMF effectively improved pain threshold and concurrently increased ROM (rotation to the painful side, lateral flexion to the nonpainful side). In addition, the PMF may effectively deactivate UT activity during abduction and the muscle activity ratio between UT and serratus anterior. Conclusion: These findings provided empirical evidence that PMF can be an effective treatment method to reduce pain threshold, to increase cervical ROM, and deactivate UT activity in individuals with TrP.