• Proceedings of the KIEE Conference
• /
• 2005.07b
• /
• pp.1506-1508
• /
• 2005

VCO(voltage controlled oscillator) using mobile communication device decides direct characteristics as parts that affect important in stable oscillation and distortion characteristics of system. VCO used 900 MHz band was designed by the transformation of Colpitts circuit form use ADS that consider Q-factor to minimize phase noise. VCO manufactured together evaluation board and voltage control oscillator to FR-4 PCB. VCO experimented chracteristics after control through resonance department tuning. In our research, the designed VCO has 15.5 dBm output level at the bias condition of 6V and 10mA and the operating frequency range of 917 MHz$\sim$937 MHz band. Phase noise is -98.28 dBc/Hz at 1 MHz frequency offset from the carrier.

• Journal of the Korean Society for Precision Engineering
• /
• v.16 no.9
• /
• pp.104-109
• /
• 1999

The flywheel energy storage system using superconducting magnetic bearings is a device to store electrical energy as rotatioal kinetic energy by motor and to convert it to electrical energy by generator when it is necessary. The rotordynamic analysis should be performed with an adequate analytical model and equations of motion to identify the stable driving condition and the dynamic behavior. The critical speed and the unbalance response of superconducting magnetic bearings-flywheel system are studied in this paper. The analytical results show that the system has one forward whirling mode and two backward whirling models below 500rpm. The maximum displacement 0.75mm is detected at the first forward mode (385rpm)through unbalance response analysis. The analytical results are compared with the experimental result by the spin-down test. The experimental result shows that the maximum displacement is 0.7mm at 370rpm.

• Journal of IKEEE
• /
• v.23 no.1
• /
• pp.306-309
• /
• 2019

Wireless charging is a technology of transmitting power through an air gap to an electrical load for the purpose of energy dissemination. Compared to traditional charging with code, wireless power charging has many benefits of avoiding the hassle from connecting cables, rendering the design and fabrication of much smaller devices without the attachment of batteries, providing flexibility for devices, and enhancing energy efficiency, etc. A transmitting coil and a receiving coil for inductive coupling or magnetic resonant coupling methods are available for the near field techniques, but are not for the far field one. In this paper, the wireless power transfer (WPT) circuit by using magnetic resonant coupling method with a resonant frequency of 13.45 Mhz for the low power system is implemented to measure the power transmission efficiency in terms of mutual distance and omnidirectional angles of receiver.

• Journal of Biomedical Engineering Research
• /
• v.38 no.3
• /
• pp.102-110
• /
• 2017

Cancer is one of the most challenging human diseases. Current clinical methods have limitations for early-stage cancer diagnosis and effective therapy. Moreover, current surgical methods to remove tumors are not precise enough and chemotherapy destroys normal tissues as well as malignant tumors, resulting in severe side effects such as hair loss, vomiting, diarrhea, and blood disorders. Recently, nanotechnology using nano-sized particles suggests advanced solutions to overcome the limitations. Various nanoparticles have been reported for more accurate diagnosis and minimized side effects. However, current nanoparticles still show limited targeting accuracy for cancer generally below 5% injection dosage. Therefore, herein we report a new nanoparticle inducing device(NID) to guide the nanoparticles externally by using both variable magnetic fields and blood flows. NID can be a promising approach to improve targeting accuracy for drug delivery using iron oxide nanoparticles.

• Journal of the Korean Magnetics Society
• /
• v.25 no.1
• /
• pp.22-26
• /
• 2015

In this paper, a magneto-inductive wave generated in a chain of LC resonators fabricated with Ni-Zn ferrite cores and chip capacitors is presented. RF signal propagates to neighbor resonator one by one as a consequence of the magnetical coupling between two resonators in the device. The magnetical coupling is due to the mutual inductances along the chain of resonators. So, the signal amplitude (${\approx}$ coupling intensity) is dependent of the mutual inductance which can be adjusted by applied magnetic field. In order to demonstrate the device, some experiments have been carried out systemically. The transmission characteristics of a magneto-inductive wave could be controlled by applied external magnetic field. The device composed of 5 resonators; the center frequencies were estimated to be 32 MHz and 38 MHz with the external magnetic flux density of 75 Oe and 222 Oe, respectively. We expect that the reported results could open a promising way to a high variety of applications in one- and two-dimensional functional devices, such as transducers, delay lines, power dividers and couplers.

• Journal of the Korean Magnetics Society
• /
• v.8 no.4
• /
• pp.231-240
• /
• 1998

We investigated that the fabrication and reproducing signal characteristics of tri-layered magnetoresistance (MR) element for the high density magnetic thin film heads and sensors. Magnetoresistance curve of tri-layered MR element predicted by computer modeling was saturated above external field of -15 Oe~+22 Oe, and it was shifted to linearized region as large as 4 Oe. In the case of fabricated real device, magnetoresistance curve was saturated above external field of $\pm$15 Oe, and it was shifted to linearized region as large as 4 Oe. As shown in real device, MR response curve was in good agreement with the simulation results. As a result of experimental data of reproducing output signal in real device, it retained normal sinusoidal waveforms in 1~4 Oe external magnetic field. In this magnetic field region, the fabricated heads with tri-layered MR element can be operated with good reproduced characteristics. This will be beneficial to the use of efficient processes of manufacturing elements and the vacuum deposition techniques which control thin film properties.

• Journal of Institute of Convergence Technology
• /
• v.3 no.2
• /
• pp.11-15
• /
• 2013

These days, the quality of goods is required to improve in the process of manufacturing the semiconductor through the short working hours and clean transportation. The non-contact transport device using magnetic levitation can be a solution in the manufacturing process. The non-contact transport device, using electromagnetic actuation, is the system that can actually transport them by only using attraction force from the electromagnetic source without authentic contact. Moreover, the system using electromagnetic force has a substantial number of benefits ranging from unrestricted design to unlimited expansion. Especially, the price is competitive. The non-contact transport device, using electromagnetic force, has another merits in controlling by giving the same amount of attraction force to ferromagnetic body. By controlling the currents given to coil, the operator is able to decide the direction of the transportation. In order to design the optimal system, we implemented five different things such as the presence of the links below the electromagnetic, the electromagnet changes due to coupling method, the change according to the thickness of the links below electromagnet, due to changes in between electromagnetic distance direction, and the size of the current. Through simulations and the optimum design, it seems to control easily and figure out the exact size of power. It might definitely be the non-contact transport that can sharply reduce tiny scratches and particles in the process of manufacturing the semiconductor.

• Journal of the Korean Magnetics Society
• /
• v.25 no.5
• /
• pp.149-155
• /
• 2015

The ECR (Electron Cyclotron Resonance) Ar ion milling was manufactured to fabricate the device of thin film. The ECR ion milling system applied to the device etching operated by a power of 600W, a frequency of 2.45 GHz, and a wavelength of 12.24 cm and transferred by a designed waveguide. In order to match one resonant frequency, a magnetic field of 908 G was applied to a cavity inside of ECR. The Ar gas intruded into a cavity and created the discharged ion beam. The surface of target material was etched by the ion beam having an acceleration voltage of 1000 V. The formed devices with a width of $1{\mu}m{\sim}9{\mu}m$ on the GMR-SV (Giant magnetoresistance-spin valve) multilayer after three major processes such as photo lithography, ion milling, and electrode fabrication were observed by the optical microscope.

• Journal of Magnetics
• /
• v.2 no.1
• /
• pp.28-33
• /
• 1997

Very large in electrical resistivity by several orders of magnitude is obtained when an external magnetic field is applied to the colossal magnetoresistnace (CMR) materials such as La-Ca-Mn-O. The magnetoresistance is strongly temperature-dependent, and exhibits a sharp peak below room temperature, which can be shifted by adjusting the composition or processing parameters. The control of lattice geometry or strain, e.g., by chemical substitution, epitaxial growth or post-deposition anneal of thin films appears to be crucial in obtaining the CMR properties. The orders of magnitude change in electrical resistivity could be useful for various magnetic and electric device applications. .

• Proceedings of the KIEE Conference
• /
• 1996.07a
• /
• pp.202-204
• /
• 1996

A superconducting magnetic energy storage device(SSD) system has being developed to provide power to industrial electric loads subjected to short term voltage disturbances. In this paper, the results of the conceptual design of SSD system are described.