• Journal of Magnetics
• /
• v.8 no.1
• /
• pp.74-78
• /
• 2003

The largest advantage of magnetic micromachine is wireless operation. This advantage makes it suitable for medical micromachine working inside the human body. In the medical field, low invasion treatment is very important From this point of view, very small machines working in the body without power supply cables meet the needs of the medical field. In this paper, we report about magnetic wireless actuators for medical applications.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.08a
• /
• pp.107-109
• /
• 2003

The magnetostriction of FeCoGe/phenol composites is measured under the external magnetic field. A few Measurement are carried out by using the electrical-resistance strain gage, the Wheaton Bridge for eliminating the unnecessary voltage, the lock-in-amplifier for the signal amplification and noise filtering. When the external magnetic field is applied to the longitudinal direction against those samples which is the 10wt.% phenol in composites, the theoretical maximum strain of 120ppm is obtained. According to the larger strain than that of others solid state actuators and piezoelectric actuators. FeCoGe/phenol composites could be useful as an actuator.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.11a
• /
• pp.325-328
• /
• 2003

The magnetostriction of FeCoGeW/phenol composites is measured under the external magnetic field. A few Measurement are carried out by using the electrical-resistance strain gage, the Wheaton Bridge for eliminating the unnecessary voltage, the lock-in-amplifier for the signal amplification and noise filtering. When the external magnetic field is applied to the longitudinal direction against those samples which is the 10wt.% phenol in composites, the theoretical maximum strain of 120ppm is obtained. According to the larger strain than that of others solid state actuators and piezoelectric actuators. FeCoGeW/phenol composites could be useful as an actuator.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2004.10a
• /
• pp.548-551
• /
• 2004

Magnetostrictive actuators have seen increasing use in fine positioning system because it has many advantages such as friction free, resolution of ${\mu}{\textrm}{m}$ or nm scale, and powerful output force. Usually, the magnetic circuit of magnetostrictive actuator has components which are flux return path, coil, and magnetostrictive material. It is classified in two types according to existence of the permanent magnet. The magnetic circuit having optimal performances transfer magnetic field which is obtained by providing input current at coil without energy loss. This paper described mathematical model of magnetic circuit for getting design variables. The modeling equation is obtained from the relations between flux and reluctance of the magnetic equivalent circuit. Also, finite element analysis has been used to study the performance of magnetic circuit according to change of design variables such as existence and shape of the permanent magnet, flux return path etc. The modification of dimensions enables us to optimize magnetic circuit.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2003.06a
• /
• pp.652-655
• /
• 2003

This paper is about the recent development of the magnetic impact actuator for endoscope. The developed magnetic impact actuator has many problems to arrange in the system body. Because the magnetic impact actuator need a permanent magnet as an impacter, so the magnetic interference among magnets can not be eliminated. This interference causes the system size bigger. We need a new actuator design to solve these problems. One of the good solutions is to use the closed electro-magnetic circuit. This kind of circuit enhances the actuators to be independent. It is written about the design of the electro-magnetic circuit and simulation using Maxwell(version 9.0)

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.19 no.9
• /
• pp.2082-2088
• /
• 1995

In this paper, we designed and fabricated the magnetic bearings and built-in type cylindrical capacitive transducers for improving the vibration characteristics of rotating shaft. The eddy current and magnetic field from the electromagnet of the bearing don't affect the measuring signal of the capacitive type transducers so that it is possible to locate the capacitive sensor plates around the magnetic bearing poles and can improve the spillover problem which is induced by the noncollocation of the sensors and actuators. According to the sensitivity calibration schemes using a X-Y table, the cylindrical capacitive transducers have a good linearities in the .+-.70.mu.m range from the geometric center of the sensor plates. The measured results also show high displacement sensitivities of the sensors. According to the performance test of the magnetic bearing which is controlled by the analog PD controllers, we found that the built-in capacitive transducer system successfully measures the journal displacement in the magnetic field and therefore the magnetic bearing system supports the rotating shaft up to 12,000 rpm.

• Journal of the Korean Society for Precision Engineering
• /
• v.20 no.5
• /
• pp.180-188
• /
• 2003

In the precision motion device, the frictional problem by mechanical friction causes serious effects on the system performance. Various researches have been executed to solve this problem, but classical fluid lubrication method has some disadvantages in precision motion under clean environment. Therefore, the magnetic bearing and contact-free systems have been focused on with its pollution-free characteristics. In this paper, we treat modeling and analysis of electromagnets not only for magnetic bearing but also fer contact-free electromagnetic actuators. Three types of electromagnet for various applications are modeled and analyzed by magnetic circuit theory and the validity is verified by experiments.

• International Journal of Precision Engineering and Manufacturing
• /
• v.7 no.4
• /
• pp.28-33
• /
• 2006

Various precision engineering studies have attempted to remove mechanical friction, which causes the performance of a system to deteriorate, from precision positioning devices. Since the classical fluid lubrication method has some disadvantages in clean environments, attention has been focused on magnetic bearings and contact-free systems with their pollution-free characteristics. In this paper, f electromagnets are modeled and analyzed, not only for magnetic bearings but also for contact-free electromagnetic actuators. Three types of electromagnets that are appropriate for various applications were considered using magnetic circuitry theory. The results were experimentally validated.

• Journal of the Korean Society for Precision Engineering
• /
• v.15 no.11
• /
• pp.233-243
• /
• 1998

The demand of high speed machining is increasing due to the high speed cutting and grinding provides high efficiency of process, short process time, improved metal removal capacity and better surface finish. Active magnetic bearings allow much high surface speed than conventional ball bearings and therefore greatly suitable for high speed cutting or grinding. This paper describes a design process of an active magnetic bearing system for a high speed grinding spindle with power 5.5kW and maximum speed 60,000rpm. Magnetic actuators are designed by the magnetic circuit theory considering static load condition, and examined with FEM analysis. Dynamic characteristics are also considered, such as bandwidth, stiffness, natural frequency and static deflection. System characteristics are simulated with a rigid rotor model.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2004.04a
• /
• pp.398-403
• /
• 2004

The demand of high speed machining is increasing because the high speed cutting providers high efficiency of process, short process time, improved metal removal capacity and better surface finish. Active magnetic bearings allow much high surface speed than conventional ball bearings and therefore greatly suitable for high speed cutting. The automatic control concept of magnetic bearing system provides ability of intelligent control of spindle system to increase accuracy and flexibility by means of adaptive vibration control. This paper describes a design and development of a milling spindle system which includes built-in motor with power 5.5㎾ and maximum speed 70,000rpm, HSK-32C tool holer and active magnetic bearing system. Magnetic actuators are designed for satisfying static load condition. The Performances of manufactured spindle system was examined for its static and dynamic stiffness, load capacity, and rotational accuracy. This spindle was run up to 70,000 rpm stably, which is 3.5 million DmN.