• Proceedings of the Korean Magnestics Society Conference
• /
• 2016.05a
• /
• pp.137-137
• /
• 2016

• Korean Journal of Materials Research
• /
• v.12 no.11
• /
• pp.880-882
• /
• 2002

We have prepared magnetic thin films of FeSiB by sputtering and examined microstructure and magnetic properties of the annealed films in order to investigate the feasibility of the films to microsensor application. Effects of vacuum annealing on the magnetic properties of $Fe_{84}$$Si_{6}$$B_{10}$ films have been examined as a function of temperature. The heating rate and the holding time were 10 K/min and 1 hour, respectively. Vacuum condition was held during cooling to prevent oxidation of the films. The coercivity did not show any noticeable change (~1500 A/m), although the grain size of the crystalline phase in the annealed films increased gradually up to about 16 nm until 673 K. However, both the grain size and the coercivity increased steeply when the annealing temperature increased over 723 K. Since the saturation magnetization is closely related to the phase evolution, the variation of the saturation magnetization of the annealed films was similar to that of the ribbon materials; the thin films were transformed from amorphous to crystalline with $\alpha$-(Fe,Si) phase by increasing annealing temperature.

• Journal of Powder Materials
• /
• v.22 no.1
• /
• pp.39-45
• /
• 2015

In this study, cobalt nanopowder is fabricated by sonochemical polyol synthesis and magnetic separation method. First, sonochemical polyol synthesis is carried out at $220^{\circ}C$ for up to 120 minutes in diethylene glycol ($C_4H_{10}O_3$). As a result, when sonochemical polyol synthesis is performed for 50 minutes, most of the cobalt precursor ($Co(OH)_2$) is reduced to spherical cobalt nanopowder of approximately 100 nm. In particular, aggregation and growth of cobalt particles are effectively suppressed as compared to common polyol synthesis. Furthermore, in order to obtain finer cobalt nanopowder, magnetic separation method using magnetic property of cobalt is introduced at an early reduction stage of sonochemical polyol synthesis when cobalt and cobalt precursor coexist. Finally, spherical cobalt nanopowder having an average particle size of 22 nm is successfully separated.

• Journal of Powder Materials
• /
• v.15 no.1
• /
• pp.37-45
• /
• 2008

This article presents the challenges toward the successful consolidation of $Al_2O_3$ nanopowder using magnetic pulsed compaction (MPC). In this research the ultrafine-structured $Al_2O_3$ bulks have been fabricated by the combined application of magnetic pulsed compaction (MPC) and subsequent sintering, and their properties were investigated. The obtained density of $Al_2O_3$ bulk prepared by the combined processes was increased with increasing MPC pressure from 0.5 to 1.25 GPa. Relatively higher hardness and fracture toughness in the MPCed specimen at 1.25 GPa were attributed to the retention of the nanostructure in the consolidated bulk without cracks. The higher fracture toughness could be attributed to the crack deflection by homogeneous distribution and the retention of nanostructure, regardless of the presence of porosities. In addition, the as consolidated $Al_2O_3$ bulk using magnetic pulsed compaction showed enhanced breakdown voltage.

• Proceedings of the KIEE Conference
• /
• 1989.07a
• /
• pp.291-294
• /
• 1989

The effect of isothermal aging on the crystallization of $Fe_{78}B_{13}Si_9$ metallic glass has been investigated by electrical resistivity, X-ray measurements, bending test, thermal analysis and transmission electron microscpy. Amouphous $Fe_{78}B_{13}Si_9$ alloy was annealed isothermally for 5 to 1200 min. between $300^{\circ}C$ and $540^{\circ}C$. It has been found that close relation between relative resistivity and X-ray diffraction pattern showed. The crystalline peaks of ${\alpha}$-(Fe, Si) and $Fe_2B$ are detected by X-ray experiment. The crystalline phases observed by TEH show ${\alpha}$-(Fe, Si) and $Fe_2B$ with dendritic and cylindrical morphology, respectively. It has been also found that the embrittleness of aged samples rapidly increased with the crystallization and was shown before the crystallization.

• Journal of Magnetics
• /
• v.1 no.1
• /
• pp.19-23
• /
• 1996

In the present study, the $Sm_2Fe_{17}N_x$-type interstitial materials have been prepared by reaction between Nb-free or Nb-containing $Sm_2Fe_{17}$-type alloy and $N_2$ gas. Nitrogenation behaviour of the $Sm_2Fe_{17}N_x$-type material and disproportionation characteristics of the nitrogenated materials have been studied by means of differential thermal analysis (DTA) and thermopiezic analysis (TPA). Magnetic properties of the produced $Sm_2Fe_{17}N_x$-type interstitial materials were characterised in vibrating sample magnetometer (VSM) or thermomagnetic analyser (TMA). Epoxy-bonded or Zn-bonded $Sm_2Fe_{17}N_x$-type magnets were prepared, and their magnetic properties were investigated. It has been found that nitrogenation kinetics of the Sm2Fe17Nx-type alloy is improved significantly by the Nb-substitution for Fe in the alloy. The Nb-substitution is also found to enhance thermal stability of the $Sm_2Fe_{17}N_x$-type interstitial material. Hard magnetic properties of the interstitial materials produced from Nb-free orNb-containing alloy is high enough (intrinsic coercivity : over 7 kOe) for application as bonded permanent magnets. The good hard magnetic properties of the interstitial material are maintained in the epoxy-bonded magnet. Intrinsic coercivity of the Zn-bonded magnets is improved significantly as post-bonding annealing time increases.

• Korean Journal of Materials Research
• /
• v.31 no.12
• /
• pp.690-696
• /
• 2021

The purpose of this study is to develop a zirconium-based alloy with low modulus and magnetic susceptibility to prevent the stress-shielding effect and the generation of artifacts. Zr-7Cu-xSn (x = 1, 5, 10, 15 mass%) alloys are prepared by an arc melting process. Microstructure characterization is performed by microscopy and X-ray diffraction. Mechanical properties are evaluated using micro Vickers hardness and compression test. The magnetic susceptibility is evaluated using a SQUID-VSM. The average magnetic susceptibility value of the Zr-7Cu-xSn alloy is 1.176 × 10^-8 cm³g^-1. Corrosion tests of zirconium-based alloys are conducted through polarization test. The average Icorr value of the Zr-7Cu-xSn alloy is 0.1912 ㎂/cm². The elastic modulus value of 14 ~ 18 GPa of the zirconium-based alloy is very similar to the elastic modulus value of 15 ~ 30 GPa of the human bone. Consequently, the Sn added zirconium alloy, Zr-7Cu-xSn, is very interesting and attractive as a biomaterial that reduces the stress-shielding effect caused by differences of elastic modulus between human bone and metallic implants. In addition, this material has the potential to be used in metallic dental implants to effectively eliminate artifacts in MRI images due to low magnetic susceptibility.

• International Journal of Precision Engineering and Manufacturing
• /
• v.3 no.1
• /
• pp.13-19
• /
• 2002

Although the design of magnetic bearing needs a systematic optimization due to several design variables, constraints, geometric limitations, nonlinearities, and so on, the present designs for magnetic bearings have been conducted in the linear region of the characteristics for magnetic materials by trial and error considering design constraints. This article, therefore, provides the possibility of a genetic algorithm(GA) based optimization with two dimensional nonlinear finite element magnetic field analysis for the design of a radial heteropolar magnetic bearing. The magnetic bearing design by GA based optimization makes good agreements with that by a commercial optimization software DOT using the sensitivity analysis.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.19 no.3
• /
• pp.313-320
• /
• 2010

The magnetic abrasive polishing (MAP) process is used to achieve the nano-meter grade polishing results on flat or complicated surface. In previous study, polishing the stainless steel plate which is a non-magneto-material was tried. To polish non-magneto-materials using the MAP process was very difficult because the process was fundamentally possible by the help of a magnetic force. Therefore, it had lower efficiency than magneto-materials such as SM45C. In this study, optimization for tool geometry of the MAP was performed to improve the magnetic force between tool and workpiece. Moreover, a permanent magnet was installed below the non-magneto-material to improve the magnetic force. And then the design of experiments was carried out to evaluate the effect of the MAP parameters on the polishing results.

• Proceedings of the Korean Magnestics Society Conference
• /
• 2000.09a
• /
• pp.200-206
• /
• 2000

We have investigated the activation magnetic moment, which characterizes the basis magnetic moment acting as a single magnetic particle during magnetization reversal. The activation magnetic moment was measured from each local area on continuous ferromagnetic thin films, by analyzing the magnetic field dependence of magnetization reversal of the corresponding local area based on a thermally activated relaxation process. It was found that the activation magnetic moment was nonuniform on submicrometer scale; the fluctuation increased with increasing the number of layers in Co/Pd multilayers. The distribution could be well analyzed by exp($\delta$m$\^$3/2/), where $\delta$m is the deviation of the activation magnetic moment from the mean value.