• Journal of Magnetics
• /
• 제15권3호
• /
• pp.143-147
• /
• 2010

Rotary-type voice coil motors are widely used as actuators in hard disk drives. The recent trend toward higher density and smaller form factors in data storage devices requires performance improvement of the voice coil motor. In this study, we introduce a Halbach magnet array to the voice coil motor in order to increase the force generation. The Halbach magnetic circuit outperforms the conventional magnetic circuit due to the confined magnetic flux. To investigate the performance of the Halbach magnetic circuit, we analyze air gap flux density with the various shapes and thickness of the magnets using 3-dimensional finite element analysis. Consequently the optimum shape of the Halbach magnetic circuit is proposed. Simulations and experimental results proved effectiveness of the proposed magnet array in the voice coil motor for a commercial hard disk drive.

• 한국자기학회:학술대회 개요집
• /
• 한국자기학회 1994년도 춘계연구발표회 논문개요집
• /
• pp.12-13
• /
• 1994

Magnetic recording is still considered to be a.leader in storage industries in general. The rigid disk drive, in particular, has an advantage over tape, optical, magneto-optical, or flash memories, because of high areal density and fast access time with reasonably low cost per Mbyte. However, to be competitive in the market and to keep an edge over other storage devices, head and media in rigid disk drives require better performance per cost and more aggressive improvement in areal density, as shown in Fig. 1, than before. In this review paper, the future trend in head/media technologies of the rigid disk drive has been reviewed. Thin film media and thin film inductive/MR heads will be mainly discussed, since they are expected to be dominant in the future high-end drives over other technologies, such as particulate media or MIG heads.(omitted)mitted)

• Tribology and Lubricants
• /
• 제15권4호
• /
• pp.335-342
• /
• 1999

Corrosion of the disk has been an ongoing concern for the manufacturers of hard disk drives. With the advent of magnetoresistive (MR) head, very low levels of corrosion and contamination become more critical since the raised defects and corrosion products on the disk surface-anything that heats the MR sensor due to the contact-can distort the output signal of the head. This phenomenon is called as thermal asperity. In this paper, the effect of corrosion as a form of Co migration on the occurrence of thermal asperity in MR drives was investigated. The corrosion test at high temperature (60$^{\circ}C$) and high relative humidity (80%) was emphasized in this study and the testing results at ambient condition were compared. The corrosion on the disks was characterized as the amount of Co ion migration using an ion chromatography (IC) and a time-of-flight secondary ion mass spectroscopy (TOF-SIMS). It is proved that corrosion on the disk surface after storage testing is closely correlated to the amount of Co ions migration from the magnetic layer to disk surfaces and higher Co migration causes more thermal asperities in the drive. In order to reduce Co migration, several methods such as burnishing process and structure of the carbon overcoat were investigated. It is found that the hydrogenated carbon overcoat shows the least Co migration among different types of overcoat layer. However, the most effective way to reduce Co migration is the application of Cr layer between the overcoat and the magnetic alloy layer.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 2002년도 proceedings of the second asia international conference on tribology
• /
• pp.281-282
• /
• 2002

To reduce the spin-off of lubricants on a magnetic disk, which is caused by the radial component of shear force between the disk and air, we analyzed the air-velocity distribution and the air-shear force by three-dimensional large-eddy simulation (LES). This sensitivity analysis, on five design parameters, showed that disk/arm clearance and arm thickness have a greater effect on the mean radial air-shear force than the other parameters. The force on a disk optimized according to the optimum parameters is 12% less than the force on a conventional disk.

• 한국정밀공학회지
• /
• 제22권10호
• /
• pp.174-185
• /
• 2005

This paper presents the design, fabrication, and testing results of a dual stage actuator system for a fine positioning of magnetic heads in magnetic disk drives. A novel rotary microactuator which is electrostatically driven and utilized as a secondary actuator was designed. The stator and rotor electrodes in the microactuator was revised to have the optimal shapes and hence produces much higher rotational torque compared with the conventional comb-shape electrodes. The microactuators were successfully fabricated using SoG(silicon on glass) processing technology, which is known as being cost-effective. The fabricated microactuator has the structural thickness of $45{\mu}m$ with the gap width of approximately $3{\mu}m$. The dynamic characteristic of microactuator/slider assembly was investigated, and its natural frequency and DC gain were measured to be 3.4kHz and 32nm/V, respectively. The microactuator/slider assembly was integrated into a HDD model V10 of Samsung Electronics Co. and a dual servo algorithm was tested to explore the tracking performance of dual stage actuator system where the LDV signals instead of magnetic head signals were used. Experimental results indicate that this system achieves the tracking accuracy of 30nm. This value corresponds to a track density of 85,000 track per inch(TPI), which is about 3 times greater than that of current hard disk drives.

• Journal of Mechanical Science and Technology
• /
• 제15권3호
• /
• pp.281-290
• /
• 2001

Particle contamination has been an ongoing problem affecting the reliability of the magnetic hard disk drives. Especially the recent use of MR head requires much tighter control of particle contamination due to thermal asperity (TA) phenomenon. In this study, the effects of slider air bearing surface design of TA reduction capability were investigated by manufacturing two types of sliders. Numerical methods were used to simulate the motion of particles in the head/media interface. Experiments were conducted to verify the results predicted by the numerical simulation. Drives were built and exposed to particle contamination using a particle injection chamber, which turned out to be a very simple and reliable particle generation method over conventional aerosol technique. Then the number of TA generated in the drives was recorded and compared. Also the contacts between slider and particles were investigated by acoustic emission study. It was found that a new ABS design, which has aerodynamic U-shaped rail and central flow passage, was beneficial in reducing the particle contamination on the slider.

• 진공이야기
• /
• 제5권1호
• /
• pp.4-8
• /
• 2018

Many devices based on magnetism such as power generators and motors are frequently used in real life. Magnetic materials at nano-scale can be utilized as storage devices such as magnetic tapes and hard disk drives as well as spintronics. In addition to spintronics, magnetic biosensors are another interesting application of magnetic devices at nano-scale. Here, we briefly review magnetic nano-biosensors including Hall-effect sensors, giant magnetoresistive sensors, and tunnel magnetoresistive sensors for many biomedical applications.

• 한국자기학회지
• /
• 제5권5호
• /
• pp.695-701
• /
• 1995

Fundamental issues and general procedures of modeling the head disk interface (HDI) in order to provide design criteria for future ultra-low flying sliders are given. Intermittent contact and gaseous rarefaction effects are discussed using nonconventional kinetic theory. To illustrate the simulation results, we modeled IBM 3370 taper flat sliders and positive/negative "bow tie" sliders. Several alternative HDI concepts for future disk drives - viscoelastic bearings, a hybrid system, and contact recording - are also briefly discussed.

• 소음진동
• /
• 제10권6호
• /
• pp.977-984
• /
• 2000

Vibration of disk drive spindle is one of the major limiting factors in achieving higher track densities in hard disk drives. Vibration of a BLDC motor is a coupled phenomenon between mechanical characteristics and magnetic origins through the motor air-gap. In this paper, radial magnetic forces for symmetric and asymmetric BLDC motor are calculated with respect to the various rotor eccentricity using analytic method. Based on the results of the radial magnetic forces, transient whirl responses of the spindle motor are analyzed using finite element and transfer matrices. Results show that an asymmetric motor has a worse effects on unbalanced magnetic forces and vibration when mechanical and magnetic coupling exists.

• Tribology and Lubricants
• /
• 제17권4호
• /
• pp.312-320
• /
• 2001

In magnetic hard disk drives, higher areal recording density requires reduction of head-disk spacing. To overcome the increase of stiction associated with reduction of head-disk spacing, a padder slider, which adds pads to slider's air bearing surface, can be one of the practical solution for sub 20 nm flying height, and even for near contact recording. This study investigated the tribological characteristics of a padder slider. A padder slider took off slowly but showed less friction force than a normal slider. The hot/dry CSS test and drag test indicated that pad wear of a padder slider was negligible. The tribological performance of disk is an important factor to be considered. In particular, less carbon overcoat layer of the disk will result in higher stiction and wear in slider/disk interface. In conclusion, a padder slider shows encouraging tribological performances for practical use in HDD.