• 한국엔터테인먼트산업학회논문지
• /
• 제5권2호
• /
• pp.166-172
• /
• 2011

저가의 홀센서를 이용하여 자석의 위치를 인식하는 센서 시스템을 제안하였다. 먼저 모델식을 이용하여 자석에 의한 자기장을 측정하고, 수평 자계와 수직 자계의 특성을 분석하여, 센서의 배치방법을 결정하였다. 자석과 홀센서의 위치 관계에 따라서 측정된 자기장 값으로부터 자석의 위치를 추정하는 알고리즘을 제안하고, 이론적인 오차를 계산하였다. 또한 마이크로 컨트롤러를 사용하여 개발할 때의 단점인 실시간 데이터 확인이 어려운 점을 극복하기 위해서 컴퓨터용 응용 프로그램을 작성하여, 작업의 수월성을 높였다. 계산된 이론적 오차는 0.0025cm 이하로 나타났으며 실제로 개발된 시스템의 오차는 0.07cm 이하로 측정되어 여러 가지 상황에서 제안한 방법들의 우수성을 입증하였다.

• 대한전기학회논문지:전기기기및에너지변환시스템부문B
• /
• 제55권7호
• /
• pp.346-352
• /
• 2006

In Brushless DC Motor, there are Permanent Magnets (PMs) with driving circuit and sensor for detecting to rotor position and rotation speed. In the case of using hall IC sensor which response to magnetic flux, that is required to additional sensor magnet for rotor position detecting. Most of BLDC motor, However, take asymmetrical overhang of PM in rotor instead of additional sensor magnet for operating of hall IC sensor. The asymmetrical overhang of PM occur rotor thrust to z-axis direction that is lead to not only damage of bearing but also intensive noise and vibration. Therefore, the analysis of magnet overhang effect in the side of vibration and drive to hall If sensor is required to precise. In this paper, 2-D Finite Element Method is used to solve precise field computation and thrust of z-axis direction considering asymmetrical magnet overhang. And also the z-axis thrust from the analysis result is compared to experimental result. In conclusion, the purpose of this paper minimize to noise and vibration of BLDC Motor as analyzes to asymmetrical magnet overhang effect.

• Journal of Power Electronics
• /
• 제10권3호
• /
• pp.300-305
• /
• 2010

This paper presents a two Hall sensor method for rotor angle detection in permanent magnet synchronous motors (PMSM). To minimize the implementation complexity, the system is designed to measure the edge field of permanent magnet pieces. However, there are nonlinearities in the measured values of the edge field. In this work, an angle correction algorithm is proposed, and the improvements in accuracy are verified through experiments. Finally, a field orientation controller is constructed with the proposed angle detection algorithm.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2005년도 추계학술대회 논문집 전기기기 및 에너지변환시스템부문
• /
• pp.107-109
• /
• 2005

This paper presents the development of the magnetic position sensor for servo motor. The magnetization system is designed for the sinusoidal magnetic flux density distribution from permanent magnet using 2D finite element method and Preisach model. The magnetic position sensor is composed of the permanent magnet and two Hall elements. And the algorithm calculating the rotating position is suggested by the phase difference of outputs of Hall elements.

• 제어로봇시스템학회논문지
• /
• 제12권4호
• /
• pp.358-363
• /
• 2006

This paper demonstrates a new non-contact electronic joystick using single hall sensor which detects a horizontal vector of the magnetic field. Furthermore, in this paper, it is mathematically modeled that nonlinear characteristics between the output of hall sensor and the movement of joystick bar. The dynamic horizontal vector of magnetic flux is detected by the hall sensor while a permanent magnet is rotated with the joystick bar, which has two dimension detecting area. Using the nonlinear adjustment equations, the output signals of hall sensor have been linearized to give higher accuracy in the two dimension movement. Finally, through the real experiments, it is showed that the single hall sensor structure mechanism is superior to the dual sensor structure in sensing the two-dimensional motion without offset.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2005년도 ICCAS
• /
• pp.2058-2062
• /
• 2005

This article describes the useful way to measure the torque and RPM of the geared motor. For this, we have made the planetary geared reduction motor including the torque sensor unit which consists of hall effects sensor and permanent magnet. Our monitoring system displays the sensing values (torque, rpm) and the calculated value (power) and it also has the network capability using the Bluetooth protocol. We will show that our solution is much more inexpensive and simple method to measure torque and rpm than before.

• 전력전자학회논문지
• /
• 제18권3호
• /
• pp.205-210
• /
• 2013

This paper presents a novel hall sensor fault detection and fault-tolerant control method for a high-speed permanent magnet synchronous motor (PMSM) drive system. A phase locked loop (PLL) type position estimator is used with a conventional interpolation based rotor position estimator to reduce position errors due to misalignment of hall sensors. The expected trigger time of hall sensor's output is used for detecting hall sensor fault condition and the PLL type position estimator is reconfigured for fault-tolerant control at the hall sensor fault condition. The proposed method can minimize current ripples during the transition from sensored control using hall sensors to sensorless control. Experimental results have been proposed to prove the validity of the proposed method.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 춘계학술대회논문집B
• /
• pp.228-234
• /
• 2001

NTMS(Non-contact Tilted-angle Measuring System) is developed by using the principle that the magnetic field of an anisotropic magnet's inner space is uniform and it's possible to measure the strength of the magnetic field using a linear hall effect sensor. In order to implement the caliper system of the geometry PIG(Pipeline Inspection Gauge) which has high accuracy and proper output voltage of the hall sensor without additional driving module or a signal amplifier, it is necessary to consider the size of the magnet, the inner space and back-yoke and the position of pin-hole in the magnet. So the optimal design method of the caliper system is proposed through analysis of NTMS's magnetic field adopting a FEM(Finite Element Method). The experimental results show that the developed caliper system can be used for the geometry pig with good performances.

• 동력기계공학회지
• /
• 제11권2호
• /
• pp.72-76
• /
• 2007

Since the magnetic bearing system has unstability inherently it is necessary to measure the displacement for stable operation. Normally the displacement measurement is implemented by using sensors. The sensor for the displacement measurement is selected by precision, installation space, effect of magnetic field and response speed. And the cost of displacement measurement sensor also is considered. At the cost the hall effect sensor has a large advantage comparing with the others. Therefore this study concern about the basis experimental test for the displacement measurement of the magnetic bearing system that uses the hall effect sensor coupled with a tiny permanent magnet. The experimental results confirm the validity and practicability for this displacement measurement sensor.

• Journal of Magnetics
• /
• 제18권4호
• /
• pp.454-459
• /
• 2013

This paper deals with an optimal angle error reduction method of magnetic position sensor using hall effect elements. The angle detection simulation for the magnetic position sensor is performed by 3 dimensional finite element method and Taguchi method, one of the design of experiments. The magnetic position sensor is required to generate ideal sine and cosine waveforms from its hall effect elements according to rotation angle for precise angle information. However, the output signals are easy to include harmonics due to uneven magnetic field distribution from permanent magnet in the air-gap in the vicinity of hall effect elements. For the Taguchi method, three design parameters related to position of hall effect elements and shape of back yoke are selected. The characteristics of optimal magnetic position sensor are compared with those of original one in terms of simulation as well as experiment. Finally, the performances of the motor adopting original model and optimal model are represented for the purpose of verification of motor performance due to signals from magnetic position sensor.