• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1996.11a
• /
• pp.15-19
• /
• 1996

The cusp height in ball end milling, flat end milling and filleted end milling according to various surface inclination angle was calculated. The calculation result shows that, for each kind of tools, there exists certain range of inclination angle in which cusp height characteristics favorable. From machining time calculation, filleted end mill found to be superior to flat end mill in rough machining of sculptured surface.

• Journal of the Korean Society for Precision Engineering
• /
• v.15 no.9
• /
• pp.135-144
• /
• 1998

High speed machining is a key issue in die and mold manufacturing recently. Even though this technology has great potential of high productivity. tool wear accelerated by high cutting speed to the hardened materials is other barrier. In this research, we attempted to reduce tool wear by considering tool inclination angle between tool and workpiece. The boundary lines describing machined sculptured surfaces were represented by both of cutting envelop condition and the geometric relationship of successive tool paths. Chip cross section, and cutting length could be obtained from the calculated cutting edge and the rotational engagement angle. From the simulation results, machining inclination angle of tool of $15^\circ$ was good enough from the point of tool wear and cutting force, and this value was verified through the cutting experiment of high speed ball end milling.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.10 no.4
• /
• pp.55-64
• /
• 2001

In this study, hemisphere and cylindrical shapes were machined for different tool paths and machining conditions with ball endmill cutters. Tool deflection, cutting forces and shape accuracy were measured according to the inclination position of the sculptured surface. As the decreasing of inclination position angle, the tool deflection was increased due to the decreased cutting speed when the cutting edge is approaching toward the center. Tool deflection when upward cutting is obtained less than that of downward cutting and down-milling in upward cutting showed the least tool deflection for the sculptured surface. Roundness values were found in least roundness error when down-milling in upward cutting. It is obtained the very little difference between 90。and 45。 of inclination position angle. The best surface roughness value was obtained in upward up-milling and showed different tendency with tool deflection and cutting force. For down-milling, the cutting resistance of the side wall direction is larger than that of feed direction. Therefore, this phenomenon which is received over cutting resistance can be caused of chatter.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.1 no.1
• /
• pp.5-14
• /
• 2002

Hemisphere shapes were machined for different tool paths and machining conditions with ball endmill cutters. It was also found out how feedrate affect the precision of the machining and also tried to study the most suitable feedrate in specific cutting condition. Tool deflection, cutting forces and shape accuracy were measured according to the inclination position of the sculptured surface. As the decreasing of inclination position angle, the tool deflection was increased due to the decreased cutting speed when the cutting edge is approaching toward the center. Tool deflection when upward cutting IS obtained less than that of downward cutting and down-milling in upward cutting showed the least tool deflection for the sculptured surface. For down-milling, the cutting resistance of the side wall direction is larger than that of feed direction. It was found that the tool deflection is getting better as tool path is going to far from the center for convex surface.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2000.04a
• /
• pp.507-512
• /
• 2000

Due to increasing demand toward improving product quality, various methodologies have been introduced. A brush type grinding tool is one of the most frequently used one to facilitate required process. In order to produce consistent burr shape, various machining conditions have been combined applied to disk grinding process. It has been observed that the burr dimension(shape and width) depends on the inclination angle between grinding disk and workpiece. Drastic increase of tool Wear has been also observed along the inclination angle variation. Various burr shapes have been captured and analyzed using image processing technique.

• Design & Manufacturing
• /
• v.17 no.1
• /
• pp.33-39
• /
• 2023

The ball end mill is a type of cutting tool that is widely used to process complex mold shapes including aspheric surfaces. Unlike the flat end mill in which the cutting edge is formed on the cylindrical handle, the cutting edge is formed from the cylindrical handle to the hemispherical shape, which is advantageous for processing curved shapes. However, since the cutting speed continuously changes during machining due to the helix angle of the cutting edge or the machining inclination angle, it is difficult to obtain a precise machined surface. Therefore, in this paper, machining was performed while changing the helix angle of the ball end mill and the angle of the machining slope under the same cutting conditions for STD 11 material, which is widely used as a mold material. Through this, the effect of the two variables on the roughness of the machined surface was analyzed. As a result, if the helix angle was 0 degrees, it showed the best surface roughness of Ra. 0.16 ㎛. When the helix angle was 20 degrees, the best surface roughness of Ra. 0.18 ㎛ was occurred.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2004.04a
• /
• pp.105-110
• /
• 2004

This paper deals with the study of feasibility of rotary carbide tools in the machining of aluminium alloy. A rotary tool holder was designed and manufactured for this work. Experiments were performed using Taguchi methods and regression analysis to analyse the influence of various factors and their interactions on the cutting characteristics of rotary carbide tools during machining. The cutting force is influenced the most featly at the inclination angle. The surface roughness is influenced distinctly at depth of cut. It deduced an equation to predict cutting force and surface roughness. Hence, it could be concluded here that the proposed model agrees with the experimental data satisfactorily.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.4 no.4
• /
• pp.14-20
• /
• 2005

This paper deals with the study of feasibility of rotary carbide tools in the machining of aluminium alloy. A rotary tool holder was designed and manufactured for this work. Experiments were performed using Taguchi methods and regression analysis to analyse the influence of various factors and their interactions on the cutting characteristics of rotary carbide tools during machining. The cutting force is influenced the most greatly at the inclination angle. The surface roughness is influenced distinctly at depth of cut. It deduced an equation to predict cutting force and surface roughness. Hence, it could be concluded here that the proposed model agrees with the experimental data satisfactorily.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2011.06a
• /
• pp.549-550
• /
• 2011

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2003.04a
• /
• pp.161-166
• /
• 2003

The micro-extruding die is a die for manufacturing of fine-wire by extruding process. The fine-wire made from the micro-extruding can be effectively applied to fields of semiconductor parts and medical parts etc. It is predicted that the demand of fine-wire in industry is more and more increasing. In this study $\phi50\mu m$ micro-drill which is coated with diamond is used for drilling of super micro-hole sizes. For the machining of taper parts of entrance and exit, drill having $\phi50\mu\textrm{mm}$ inclination angle $20^{\circ}$and angle $30^{\circ}$ is used. This is useful for anti tool-breakage and excessive too-wear in drilling process. After micro-drilling, the polishing process by diamond abrasive and polishing wood s carried out for increasing surface roughness.