• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2003.04a
• /
• pp.454-459
• /
• 2003

The paper will present chip formation mechanism and surface integrity generation mechanism based on the systematical experimental tests. Some basic factors such as the end milling cutter tooth number, cutting forces, cutting temperature, cutting vibration, the chip status, the surface roughness, the hardness distribution and the metallographic texture of the machined surface layer are involved. the chip formation mechanism is typical thermal plastic shear localization at high cutting speed with less number og shear ribbons and bigger shear angle than at low speed, which means lack of chip deformation. The high cutting speed with much more cutting teeth will be beneficial to the reduction of cutting forces, enlarge machining stability region, depression of temperature increment, auti-fatigability as well as surface roughness. The burrs always exists both at low cutting speed and at high cutting speed. So the deburr process should be arranged for milling titanium alloy in any case.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2002.11a
• /
• pp.321.2-321
• /
• 2002

An industrial robot noise has various noise sources such as gears, motors, bearings, and controller fans. Among these, gears are the most dominant source for noise. The gear noise, caused by tooth profile, elastic deformation, machining error and wear, is directly correlated with the transmission error of mating gear. Due to the fact that has several axis and many gears, it is difficult to understand the characteristics of the vibration and noise of robots. (omitted)

• Journal of the Korean Society for Precision Engineering
• /
• v.6 no.4
• /
• pp.94-102
• /
• 1989

The effect of plastic strain on the surface integrity of mild steel (SS 41) was studied. This paper shows that the recrystallization technique is adequate to evaluate the plastic strain in a machined surface experimentally. The relations between the plastic strain and the machining conditions are quantitatively evaluated by using the recrystallization technique. The obtained results are summarized as follows. 1. The surface integrity of steel is considerably influenced by the amount of surface region deformation produced by changes in cutting conditions. 2. The plastic strain in machined surface produced by changes of the cutting conditions is evaluated by the recyrstallization technique. 3. The plastic strain increases with the increase of depth of cut and the decrease of rake angle. 4. When the cutting force is high and the rake angle is small, the value of maximum true strain reaches to high. 5. The maximum true strain is related to the cutting energy, and the values increase with the increase of the unit shear and total engergy in constant depth with the increase of the energy values.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2000.05a
• /
• pp.759-762
• /
• 2000

In order to reduce lead-time and cost, recently the technology of Rapid Prototyping and Manufacturing (PR/M) has been used widely. So various RP/M methods have been developed and these systems commercialized several years ago. But we have carried out rapid product, such as sphere, by the milling process instead of RP system. in the case of sphere with three-dimensional shape. the machining method using conventional milling machine has resulted in some troubles because of its deformation and lack of stiffness which is due to usual work piece set up method. In this paper, the feasibility of milling process which is divided into two steps such as the-upper-and-1ower-face milling process using supporting material were investigated and suggested.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 1995.06a
• /
• pp.180-187
• /
• 1995

Helical gears are machined from blanks, which are usually prepared by forging cylindrical billets at high temperatures through buster, blocker and finisher processes. As dimensions of the blank are closer to those of the machined part, machining cost can be more reduced. Therefore, there are a lot of efforts being made to optimize the forging processes in order to produce near-net shaped blanks. In the present investigation, a rigid viscoplastic finite element technique was used to analyze a helical gear blank hot forging processes and deformation, strain and temperature distributions, forging load variations during forging were obtained. In the paper, it is discussed how these results can be utilized to optimize die design, billet dimensions and press usage.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.19 no.6
• /
• pp.746-752
• /
• 2010

Rib structure has been used to bed and column of machine tool to heighten weight stiffness ratio, cost performance and weight saving. In this paper the bed rib structure was estimated with thermal characteristics. Using superposition principle, machine tool designer can describe every complicated heat generation in the machine tool thermal source. As thermal characteristics, thermal deformation of guide rail and column and Maximum-minimum temperature variation were selected. The size, configuration and direction against the thermal loading surface operated to the thermal characteristics. The DB chart was made following rib structure estimating thermal characteristics. With superposition principle and DB chart, machine tool designer can prognosticate the thermal characteristics without FEM analysis to every bed rib structure.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.17 no.4
• /
• pp.47-54
• /
• 2018

These days, the aerospace industry uses larger machining parts and assembly parts than those in the past. The assembly machines also show the same trend. This study is concerned with the alignment measuring apparatus for the B-axis of a separated multi-axis machine. The alignment measuring apparatus is widely installed for assembly machines in the aircraft assembly process. The alignment measuring apparatus consists of a swivel part and a measuring part. This is a new conceptual idea under patent. All elements of the alignment measuring apparatus are analyzed with the FEM. The analyzed result shows that the alignment measuring apparatus is high in accuracy with stability and steady deformation.

• Journal of the Korean Society for Precision Engineering
• /
• v.15 no.8
• /
• pp.11-16
• /
• 1998

Recently, the motor-integrated spindle systems have been used to simplify the machine tool structure, to improve the motion flexibility of machine tool, and to perform the high-speed machining. In this study, a static and dynamic analysis system for motor-integrated high-speed spindle systems is developed based on Timoshenko theory, finite element method and windows programming techniques. Since the system has various analysis modules related to static deformation analysis, modal analysis, frequency response analysis, unbalance response analysis and so on, it is useful in performing systematically the design and evaluation processes of motor-integrated high-speed spindle systems under windows GUI environment.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.10 no.5
• /
• pp.653-660
• /
• 1986

Two uppor bound solutions, by the force balance method and by a kinematically admissible velocity field, are compared for the metal forming problems in plane strain. It is concluded that these two approaches always give identical results when the geometrical configurations of the deformation model reman the same. By detailed derivations for plastic bending of a notched bar, closed die forging, compression of a rectangular block, machining with a restricted contact tool and plane strain backward extrusion, the identity of both approaches is verified.

• Journal of the Korean Society for Precision Engineering
• /
• v.28 no.4
• /
• pp.416-421
• /
• 2011

Recently there has been increase in need for high precision and high speed machining due to economic and environmental reasons. It is a very important issue that determines the optimal preload that is to be applied to bearings in order to satisfy the performance required in bearings according to its operation conditions. This study introduces a variable preload device that can automatically adjust the preload applied in a machine tool spindle using centrifugal force as opposed in existing rubber instrument. In this study, the deformation of the rubber device by the centrifugal force is analyzed and it is discussed that the proposed device can be worked properly through changes of the collar density.