• Bulletin of the Society of Naval Architects of Korea
• /
• v.8 no.2
• /
• pp.13-24
• /
• 1971

When friction welded material is actually used for parts of a machine, its fatigue strength is an important problem. Especially, there is no report which deals with mechanical properties of friction welded mild steel(S20C) and stainless steel(SUS27B). In this study are compared the compared the characteristics of such specimens as mild steel, stainless steel and welded material in the S-N diagram. And metallurgical consideration is directed to HAZ. The obtained results in these studies are summarized as follows; 1) The fatigue strength of welded material is slightly less than those of mild steel and stainless steel. 2) In the S-N diagram the knuckle point of welded material has larger number of cycle than that of stainless steel. 3) The fatigue notch factor of welded material is between those of mild steel and stainless steel. 4) mHv is the largest on the weld interface. It is larger before than after fatigue test on the stainless steel side. On the mild steel side it is the way around.

• The Bulletin of The Korean Astronomical Society
• /
• v.44 no.2
• /
• pp.63.3-63.3
• /
• 2019

Nearby young moving groups (NYMGs hereafter) are gravitationally unbound loose young stellar associations located within 100 pc of the Sun. Since NYMGs are crucial laboratories for studying low-mass stars and planets, intensive searches for NYMG members have been performed. For identification of NYMG members, various strategies and methods have been applied. As a result, the reliability of the members in terms of membership is not uniform, which means that a careful membership re-assessment is required. In this study, I developed a NYMG membership probability calculation tool based on Bayesian inference (Bayesian Assessment of Moving Groups: BAMG). For the development of the BAMG tool, I constructed ellipsoidal models for nine NYMGs via iterative and self-consistent processes. Using BAMG, memberships of claimed members in the literature (N~2000) were evaluated, and 35 per cent of members were confirmed as bona fide members of NYMGs. Based on the deficiency of low-mass members appeared in mass function using these bona fide members, low mass members from Gaia DR2 are identified. About 2000 new M dwarf and brown dwarf candidate members were identified. Memberships of ~70 members with RV from Gaia were confirmed, and the additional ~20 members were confirmed via spectroscopic observation. Not relying on previous knowledge about the existence of nine NYMGs, unsupervised machine learning analyses were applied to NYMG members. K-means and Agglomerative Clustering algorithms result in similar trends of grouping. As a result, six previously known groups (TWA, beta-Pic, Carina, Argus, AB Doradus, and Volans-Carina) were rediscovered. Three the other known groups are recognized as well; however, they are combined into two new separate groups (ThOr+Columba and TucHor+Columba).

• Journal of the Korean Society for Precision Engineering
• /
• v.26 no.2
• /
• pp.35-44
• /
• 2009

Long stroke Fast Tool Servo (LFTS) with maximum stroke of $432{\mu}m$ is designed, manufactured and tested for fabrication of optical free-form surfaces. The large amount of stroke in LFTS has been realized by utilizing the hinge and lever mechanisms which enable the displacement amplification ratio of 4.3. In this mechanism the peculiar shape was devised for maximizing the displacement of end tip in LFTS and special mechanical spring has been mounted to provide the sufficient preload to the piezoelectric actuator. Also, its longitudinal motion of tool tip can be measured by capacitive type displacement sensor and closed-loop controlled to overcome the nonlinear hysteresis. In order to verify the static and dynamic characteristics of designed LFTS, several features including step response, frequency response and cut-off frequency in closed-loop mode were experimentally examined. Also, basic machining result shows that the proposed LFTS is capable of generating the optical free-form surface as an additional axis in diamond turning machine.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.45 no.5
• /
• pp.1-13
• /
• 2013

This study found fit optimum C, M, Y, K solid density and $CIEL^*a^*b^*$ value to paper & ink as well as check about printing machine state for color management in H-UV waterless off-set printing first. These values applied to GRACoL G7 calibration method. This method is one of color standard management method of printing. GRACoL G7 calibration method is possible stable tone reappearance by controlling gray balance by NPDC(Natural Printing Density Curve). Also, this study used values to make device profile as result that is gotten by application of GRACoL G7 calibration method. This profile was applied to CMS(Color Management System) of H-UV waterless off-set printing, and the result was possible by color management that correspond in printing quality standard of ISO 12647-2 and GRACol 2006 specifications.

• Asian-Australasian Journal of Animal Sciences
• /
• v.5 no.2
• /
• pp.229-235
• /
• 1992

The usefulness of a portable linear electronic scanner. B-mode ultrasonic machine, was evaluated for estimating the longissimus muscle area from ultrasonic measurement of the muscle depth in 22 live pigs. The electronic scanner was easy to operate for muscle measurements in live pigs, which did not have to be held but were caged. The cross-sectional images of longissimus muscle and covering muscles and fat appeared on the monitor with grey scale in real time. It was easy to identify the ultrasonograms of fat and muscular tissues because the images differed in the degree of the grey scale. The longissimus muscle had less echogenic image than the other muscles. The boundary lines between first, second or third layers of backfat and the longissimus muscle were distinct on the ultrasonogram. The ultrasonic measurement at the shoulder was not acceptable because of the unstable measurements and the complex tissue structure. The repeatabilities for the measurements of longissimus muscle depth at one-half body length and last rib were acceptable. The simple correlation coefficients between ultrasonic estimates of the muscle depth in live pigs and the actual areas in the carcass, were 0.50 and 0.55 at the last rib and the one-half body length, respectively. Therefore, those positions were similarly suitable to measure. The method of electronic scanner for determining longissimus muscle area from the muscle depth was suitable for practical use in the field because of the simple and inexpensive technique.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2002.10a
• /
• pp.192-197
• /
• 2002

In this study, examined the cutting characteristics of alumuminum alloy AC8A-T6 that is used to present car piston materials. And in been holding materials machining empirically escape as result that experiment comparison changing the cutting speed and feed on various condition to choose efficient machining condition. The following results can be summarized from this research. 1. As the cutting speed decreased, principal cutting force and thrust cutting force is increased, and reason that cutting force interacts greatly in the low cutting speed is thought by result by BUE's stabilization. 2. The feed speed and cutting speed increase, friction factor is decrescent and the cause appeared the thrust cutting force is fallen than cutting force relatively because chip flow according to increase of the feed rate is constraint. 3. Though specific cutting resistance grows cutting area and the feed rate are few, the cause was expose that shear angle decreases by rake face of tool gets into negative angle remarkably as wear of a cutting tool or defect part of workpiece is cut. 4. Cutting speed do greatly depth of cut is slow, surface roughness examined closely through an experiment that becomes bad, and know that it can get good surface that process cutting speed because do feed rate by 0.1mm/rev low more than 250m/min to get good surface roughness can.

• Journal of Biosystems Engineering
• /
• v.14 no.3
• /
• pp.181-187
• /
• 1989

The mechanical and rheological properties of agricultural materials which influence the machine design or handling are not completely understood. Agricultural materials do not react in a purely elastic manner, and their responses when subjected to stress and strain appear a combination of elastic and viscous behavior. Many researchers have studied the mechanical and rheological properties of the various agricultural materials, but those properties are available mostly for foreign varieties of agricultural products. Rheological properties of rice seedlings become important to formulate the principles governing their mechanical behavior. The objectives of this study were to experimentally determine the creep and recovery behavior of rice seedlings of one japonica-type and one Indica x japonica hybrid in the transplanting age. The results of this study are summarized as follows; 1. The compression creep and recovery behavior of mat-type seedlings could be described by 4-element Burger's model. 2. The steady-state creep appeared at the stress larger than 0.8 MPa and the logarithmic creep appeared at the stress smaller than 0.8 MPa. 3. In the compression creep test of the rice seedlings, the instantaneous elastic modulus of Burger's model showed the range from 20 to 40 MPa. The higher value of absolute viscosity for the rice seedling explained that the rice seedlings were viscoelastic materials. 4. In the recovery test of the rice seedlings, there was a tendency that the higher permanent strain of all samples was observed under the smaller stress being appeared, and the larger permanent strain in Dongjin was observed than in Samkang.

• Food Science and Biotechnology
• /
• v.15 no.1
• /
• pp.5-12
• /
• 2006

Degradation performance of environmentally friendly plastics that can be disintegrated by combination of sunlight, microbes in soil, and heat produced in landfills was evaluated for use in industries. Two multi-degradable master batches (MCC-101 and MCC-102 were manufactured, separately mixed with polyethylene using film molding machine to produce 0.025 mm thick films, and exposed to sunlight, microbes, and heat. Low- and high-density polyethylene (LDPE and HDPE) films containing MCC-101 and MCC-102 became unfunctional by increasing severe cleavage at the surface and showed high reduction in elongation after 40 days of exposure to ultraviolet light. LDPE and HDPE films showed significant physical degradation after 100 and 120 days, respectively, of incubation at $68{\pm}2^{\circ}C$. SEM images of films cultured in mixed mold spore suspension at $30^{\circ}C$ and 85% humidity for 30 days revealed accelerated biodegradation on film surfaces by the action of microbes. LDPE films containing MCC-l01 showed absorption of carbonyls, photo-sensitive sites, at $1710\;cm${-1}$ when exposed to light for 40 days, whereas those not exposed to ultraviolet light showed no absorption at the same frequency. MCC-101-based LDPE films showed much lower $M_w$ distribution after exposure to UV than its counterpart, due to agents accelerating photo-degradation contained in MCC-101.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.42 no.6
• /
• pp.699-705
• /
• 1997

This experiment was conducted to find out an optimum direct seeding date for rice in the southern alpine area of Korea as direct seeding method being considered as the most labor-saving method. A cultivar which was sprouted, Keumobyeo, was sown on the surface of flooded paddy from April 25 to May 15 with 5-day interval. The growth characters such plant height, tiller numbers, yield and its components as well as air temperatures were observed. Earlier sowing showed longer plant height and greater tillers than later sowing. Accumulated temperatures in the different growth stages varied from 1,010 to 1,052$^{\circ}C$ during the period from seeding date to maximum tillering stage, and from 1,785 to 1,846$^{\circ}C$ during the period from seeding to heading dates. The growth of rice sown up to May 5 showed comparatively good when compared to that of machine-transplanted rice, even though the grain yield was not competitive to that of machine-transplanted rice. Highly negative correlation coefficients were found between accumulated temperature during the period of first 30 days after seeding dates and the number of panicles, the number of spikelets per square meter, and grain yield. Regression equation between direct seeding date(X) and yield(Y;MT /ha) was $\hat{Y}$ =3.80990＋0.06207X-0.00174 $X^2$($R^2$=0.704), from which optimum seeding date for direct seeding method in alpine area was estimated to be on April 25 to May 1.

• Korean Journal of Soil Science and Fertilizer
• /
• v.24 no.1
• /
• pp.55-60
• /
• 1991

This study was carried out to obtain the effects of soil environment and characteristics on the growth and yield of young rice seedling. Twenty four rice fields were selected among the labor saving mechanization complex, and the growth statu s and various soil characteristics were investigated The young rice seedling planted soils were located at the range of elevation 5m to 210m, and the average water holding days was 5.1 days, and drainage class were mainly moderately well to imperfectly. The plant height on 30th day after machine transplanting were higher and the tiller numbers were smaller at the higher clay contents at moderately well and imperfectly drained soils. In case of sandy loam soils, the better the drainage class, the higher plant and more tillers. Soil hardness was lower in sandy loam, and the bulk densities of loam, silty clay loam and poorly drained soils were lower than the other fields. There were not differences of soil chemical properties between the soil textural groups but organic matter content were higher in poorly drained soils. The rice yields of young seedling planted fields were negatively correlated to soil bulk density and highly significantly correlated to the exchangeable calcium contents of the soils. The average yield of young rice seedlings was 487kg/10a, 2.5% higher than semi-adult rice seedling of 475kg/10a.