• Imaging Science in Dentistry
• /
• v.33 no.1
• /
• pp.21-26
• /
• 2003

Purpose: To investigate the characteristics of the newly marketed, Insight dental X-ray film. Materials and Methods: Kodak Ultraspeed (DF-58), E-speed, Agfa Dentus M2, and Kodak Insight (IP-21) films were radiographed using a Trophy intra-oral radiographic machine. 10 step exposure times were prepared and each step exposure was monitored using a FH 40G (ESM Eberline Instruments) dosimeter for each of the 4 types of intra-oral film. All films were manually processed and the radiographic densities at 6 sites of each processed film were measured, and the characteristic curves of each of the 4 types intra-oral films were created utilizing these dosimetric data and radiographic densities, based on ISO 5779. The film contrast, speed, and base plus fog density of Insight film were compared with those of the 3 other films examined in this experiment. Results : E-speed film showed greatest average gradients followed by Insight film. E-speed and Ultraspeed film showed great average gradients at low density levels. Insight film showed the fastest speed followed by E-speed, Dentus M2 and Ultraspeed film. Dentus M2 film showed greatest base plus fog density level followed by Insight film. Conclusion : Kodak Insight film showed fastest film speed with comparable film contrast on characteristic curve.

• Proceedings of the Korean Nuclear Society Conference
• /
• 2005.05a
• /
• pp.501-502
• /
• 2005

During the cut and dismantling process of HANARO irradiated instrumented capsule(03M-06U), a little different phenomenon like a jamming was observed and occurred. So to release jamming between outer pipe and inner thermal media, the outer pipe will be cut piece by piece by capsule cutting machine installed in M2 hot cell until the outer pipe was eliminated or reduced as we could. It is assumed that this kind of problem was occurred following reasons: 1) This capsule has probably a problem during manufacturing process at shop before irradiation. 2) The gap between outer pipe and thermal media is not enough to meet design criteria for thermal expansion during irradiation at HANARO

• The Journal of Advanced Prosthodontics
• /
• v.6 no.5
• /
• pp.346-350
• /
• 2014

PURPOSE. Impact forces in implant supported FDP (fixed dental prosthesis) are higher than that of tooth supported FDPs and the compositions used in frameworks also has a paramount role for biomechanical reasons. The aim of this study was to evaluate the flexural strength of two different zirconia frameworks. MATERIALS AND METHODS. Two implant abutments with 3.8 mm and 4.5 mm platform were used as premolar and molar. They were mounted vertically in an acrylic resin block. A model with steel retainers and removable abutments was fabricated by milling machine; and 10 FDP frameworks were fabricated for each Biodenta and Cercon systems. All samples were thermo-cycled for 2000 times in $5-55^{\circ}C$ temperature and embedded in $37^{\circ}C$ artificial saliva for one week. The flexural test was done by a rod with 2 mm ending diameter which was applied to the multi-electromechanical machine. The force was inserted until observing fracture. The collected data were analyzed with SPSS software ver.15, using Weibull modulus and independent t-test with the level of significance at ${\alpha}=.05$. RESULTS. The mean load bearing capacity values were higher in Biodenta but with no significant differences (P>.05). The Biodenta frameworks showed higher load bearing capacity ($F_0=1700$) than Cercon frameworks ($F_0=1520$) but the reliability (m) was higher in Cercon (m=7.5). CONCLUSION. There was no significant difference between flexural strengths of both zirconia based framework systems; and both Biodenta and Cercon systems are capable to withstand biting force (even parafunctions) in posterior implant-supported bridges with no significant differences.

• Journal of the Korean Society for Precision Engineering
• /
• v.30 no.12
• /
• pp.1303-1312
• /
• 2013

We report an ultra-precision lathe designed to machine micron-scale features on a large-area roll mold. The lathe can machine rolls up to 600 mm in diameter and 2,500 mm in length. All axes use hydrostatic oil bearings to exploit the high-precision, stiffness, and damping characteristics. The headstock spindle and rotary tooling table are driven by frameless direct drive motors, while coreless linear motors are used for the two linear axes. Finite element method modeling reveals that the effects of structural deformation on the machining accuracy are less than $1{\mu}m$. The results of thermal testing show that the maximum temperature rise at the spindle outer surface is approximately $0.5^{\circ}C$. Finally, performance evaluations of the error motion, micro-positioning capability, and fine-pitch machining demonstrate that the lathe is capable of producing optical-quality surfaces with micron-scale patterns with feature sizes as small as $20{\mu}m$ on a large-area roll mold.

• Journal of Practical Agriculture & Fisheries Research
• /
• v.21 no.1
• /
• pp.49-59
• /
• 2019

The field trial was performed to evaluate the rice growth and yield in different direct seeding methods after Italian Ryegrass Harvest The required time for seed emergence was for 7 ~ 8days in the tested direct seeding methods and there was high in seedling establishment in order of wet hill-seeding with iron-coated seeds > water seeding with iron-coated seeds > wet hill-seeding with soil coverage with pregerminated seeds. The rice plant height was shorter in the tested direct seeding methods than that of machine transplanting until 45day after seeding but there was not significant difference in terms of statistical analysis at 63day after seeding. The growth of tiller number in the rice plant was high in water seeding with iron-coated seeds and wet hill-seeding with soil coverage and low in wet hill-seeding with iron-coated seeds compared to machine transplanting. The yield component in the tested direct seeding methods was not significant difference in terms of statistical analysis. The milled rice yield in the tested direct seeding methods was higher 2 ~ 8% being with 4.94 ~ 5.24t/ha than that of machine transplanting but there was not significant difference in terms of statistical analysis. The percentage of head rice was low in the tested direct seeding methods compared to machine transplanting. The weedy rice was not occurred in the tested rice cultivation methods. In conclusion the direct seeding method would be recommended to be a suitable to in following by Italian ryegrass harvesting in southern area of Korea in terms of reduction in production cost and high income basis for rice growing farmers.

• Journal of Bio-Environment Control
• /
• v.33 no.1
• /
• pp.30-36
• /
• 2024

This study was conducted to determine the optimal working conditions when a recently developed blower-type onion stem cutter is utilized for cutting onion leaves at harvest time. The June 20 leaf cutting treatment group had the highest leaf dryness among the treatment groups (leaf dryness: 66.3%; leaf moisture content: 50.5%); the residual leaf length was 6.7 ± 3.5 cm. It is considered to have the best mechanical leaf cutting performance among the treatment groups because it is included in the optimal range of 4-10 cm. The average working speed of mechanical onion leaf cutting using the stem cutter was 0.17 m·s^-1, which is approximately 3.4 times faster than the average working speed of 0.05 m·s^-1 in the human leaf cutting treatment group. This is expected to save approximately 2.6 hours compared to human labor (based on one person) when working on a 10a area using this machine. In addition, the incidence of damaged bulbs in the machine leaf cutting treatment group was 1.3%, compared to 0.0% in the manual leaf cutting treatment group. This suggests that the mechanical leaf cutting treatment group had a higher average onion bulb decay rate during storage than the manual leaf cutting treatment group. When the storage characteristics of each treatment group were examined, the decay rate by bulb part (leaf connected or root connected) after 8 months of storage was higher in the treatment group with a residual leaf length of less than 5.0 cm after mechanical leaf cutting than in the treatment with a residual leaf length of more than 5.0 cm. This is thought to be due to the fact that treatments with a residual leaf length of less than 5.0 cm are more susceptible to infection by pathogens that cause decay during storage than treatments with a residual leaf length of 5.0 cm or more. Based on the results of this experiment, performance target of the experimental machine (residual leaf length after operation: 5 cm), and existing research on the optimal residual leaf length for onion harvesting, it is recommended to cut onion leaves so that the residual leaf length is 5-10 cm when using the stem cutter.

• Proceedings of the KIEE Conference
• /
• 2005.07b
• /
• pp.1258-1260
• /
• 2005

Superconducting synchronous motors and generators have the field coil composed of superconductor with almost zero resistance at superconducting state. Therefore, co or loss at the conventional field coil is eliminated and the superconducting machine gets higher efficiency. The armature coil of the superconducting machine is composed of cower wire and supported by non-magnetic material such as FRP(Fiber Reinforced Plastic). Although a fully-superconducting machine with superconducting armature coil has been researched, it was not developed toward industrial application because of AC transporting loss and difficulty in construction of the cooling structure and so on. This paper contains the design procedure of a 1 MW superconducting synchronous motor using high-temperature superconductor only for the field coil. Especially, the armature coil is designed by water-cooling in order to dissipate Joule heat easily. Moreover, 3-dimensional electromagnetic design is conducted to get a proper design result and reduce design errors from 2-dimensional approach.

• Journal of Technologic Dentistry
• /
• v.30 no.2
• /
• pp.79-86
• /
• 2008

The purpose of this study was to investigate the effect retention element formed by metal surface treatment method on the bond strength of indirect composite resin and metal. The metal specimens were cast from Ni-Cr alloy($Rexillium^{(R)}$ III). They were divided into 5 groups by applied retention element: $50{\mu}m$ aluminium oxide sandblasting group, $250{\mu}m$ aluminium oxide sandblasting group, 0.2mm retention crystal group, 10% $H_{2}SO_{4}$ solution etching group, $110{\mu}m$ $Rocatec^{TM}$ Plus system group. Total 50 metal specimens were veneered with Sinfony indirect composite resin system. Specimens were tested for shear bond strength on an Instron universal testing machine and fracture mode of fractured specimens were analyzed by SEM and EDS. 1. 0.2 mm retention crystals were most effective in improving the resin-metal shear bond strength (p<0.05). 2. Sandblasting by $250{\mu}m$ aluminium oxide were more effective than sandblasting by $50{\mu}m$ aluminium oxide in improving the resin-metal shear bond strength(p<0.05). 3. Fracture mode of resin-metal fractured surface were cohesive failure mode in 0.2mm retention crystal, mixed failure mode in sandblasted specimens, etched specimens and the specimens sandblasted with $110{\mu}m$ $Rocatec^{TM}$ Plus system.

• KOREAN JOURNAL OF PACKAGING SCIENCE & TECHNOLOGY
• /
• v.8 no.1
• /
• pp.15-22
• /
• 2002

We received 2 types flexible packaging films from two companies that laminated PET $16{\mu}m/dry$ lamination/aluminium foil $7{\mu}m/dry$ lamination/CPP $80{\mu}m$ films. For the reason of hot sealing's trouble through filling process, We separated each layer and compared thicks, film types and tested IR, DSC and sensory test. At the result, one sample's thick is different but film types is same between samples. Optimum hot-sealing conditions between two samples is $195^{\circ}C\;and\;210^{\circ}C$. The difference is $15^{\circ}C$. According to test of direct filling packaging process by four face fluid filling machine, two sample's sealing strength of hot-sealing is $4.76kg/cm2/15mm$(sample of optimum hot-sealing condition is $195^{\circ}C$) and $3.84kg/cm2/15mm(210^{\circ}C)$.

• Journal of Cadastre & Land InformatiX
• /
• v.48 no.1
• /
• pp.169-186
• /
• 2018

The social influence of the elderly population will accelerate in a rapidly aging society. The purpose of this study is to establish a methodology for extracting vulnerable districts of the welfare of the aged through machine learning(ML), artificial neural network(ANN) and geospatial analysis. In order to establish the direction of analysis, this progressed after an interview with volunteers who over 65-year old people, public officer and the manager of the aged welfare facility. The indicators are the geographic distance capacity, elderly welfare enjoyment, officially assessed land price and mobile communication based on old people activities where 500 m vector areal unit within 15 minutes in Yongin-city, Gyeonggi-do. As a result, the prediction accuracy of 83.2% in the support vector machine(SVM) of ML using the RBF kernel algorithm was obtained in simulation. Furthermore, the correlation result(0.63) was derived from ANN using backpropagation algorithm. A geographically weighted regression(GWR) was also performed to analyze spatial autocorrelation within variables. As a result of this analysis, the coefficient of determination was 70.1%, which showed good explanatory power. Moran's I and Getis-Ord Gi coefficients are analyzed to investigate spatially outlier as well as distribution patterns. This study can be used to solve the welfare imbalance of the aged considering the local conditions of the government recently.