• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.38C no.9
• /
• pp.740-745
• /
• 2013

This paper presents BER, FER performance comparison, especially on PHY mode of IEEE 802.15.4g and IEEE 802.11 under AWGN channel through a simulation, which is communication method using identical frequency bandwidth in M2M environment. This considers suitable communication method of required parameter. It is advantageous that FSK method is used in situations where the system require low complexity and inexpensive structure. And OFDM method is considered for system performance. Further, when the high throughput and various traffic characteristics of the system are required, it can be considered that the method of IEEE 802.11 OFDM PHY mode is used.

• Journal of the Korean Society of Industry Convergence
• /
• v.17 no.3
• /
• pp.84-92
• /
• 2014

In this paper, a novel 5-axis hybrid-kinematic machine tool is introduced and the research results on accuracy improvement of the prototype machine tool are presented. The 5-axis hybrid machine tool is made up of a 3-DOF parallel manipulator and a 2-DOF serial one connected in series. The machine tool maintains high ratio of stiffness to mass due to the parallel structure and high orientation capability due to the serial-type wrist. In order to acquire high accuracy, the methodology of measuring the output shafts by additional sensors instead of using encoder outputs at the motor shafts is proposed. In the kinematic view point, the hybrid manipulator reduces to a serial one, if the passive joints in the U-P serial chain at the center of the parallel manipulator are directly measured by additional sensors. Using the method of successive screw displacements, the kinematic error model is derived. Since a ball-bar is less expensive than a full position measurement device and sufficiently accurate for calibration, the kinematic calibration method of using a ball-bar is presented. The effectiveness of the calibration method has been verified through the simulations. Finally, the calibration experiment shows that the position accuracy of the prototype machine tool has been improved from 153 to $86{\mu}m$.

• 제어로봇시스템학회:학술대회논문집
• /
• 2005.06a
• /
• pp.1922-1927
• /
• 2005

This paper describes the mechanism of a new biped machine capable of doing human-robot cooperation work. The biped machine, WABIAN-2 is made of two seven degrees of freedom (DOF) legs, a two DOF waist and no DOF trunk. Its leg system consists of two three DOF ankles, two one DOF knees and two three DOF hips to deal with various walk motions. Its height is about 1.2[m], and its weight is 40[kg]. It is designed with large movable range as a human. Also, a knee stretch walk pattern generation for the biped machine to perform natural walk like a human is discussed in this paper. Its leg motion is compensated by using the motion of its waist. Basic knee stretch walk experiments using WABIAN-2 are conducted on the plane, and the validity of its mechanism and walk pattern generator is verified.

• Electronics and Telecommunications Trends
• /
• v.27 no.3
• /
• pp.143-152
• /
• 2012

본고에서는 Machine Type Communications(MTC) 표준화 동향을 소개한다. MTC는 사람이 개입하지 않는 상태에서 기기 및 사물 간에 일어나는 통신이라고 정의하고 있고, 사물의 이동성, 도서, 산간, 해양 등을 포함하는 광범위한 서비스 지역, 네트워크의 운영 및 유지보수의 용이성, 신뢰도 높은 데이터 전송을 위한 보안, 그리고 서비스 품질 보장 등을 고려하여, 이동통신 네트워크를 기반으로 하는 사물통신을 수용하기 위한 것이다. 우선 M2M(Machine to Machine) 개념 및 3GPP(3rd Generation Partnership Project)에서 도출한 응용 분야를 기술하고, 이어서 3GPP MTC 표준화 일정을 살펴보고, 현재까지의 주요 표준 문서의 작성 내용 중 MTC 요구사항의 정의와 구조 모델의 정의, 과부하 제어를 위한 표준화가 주된 내용으로 2011년 9월에 완성된 Release 10 NIMTC(Network Improvements for MTC) 내용을 살펴보고, 마지막으로 현재 3GPP RAN(Radio Access Network)1에서 활발하게 논의되고, 작성하고 있는 저가의 MTC 단말을 지원하기 위한 방안에 대한 기술보고서의 내용에 대해서 살펴보았다.

• Journal of the Korean Society for Precision Engineering
• /
• v.23 no.5 s.182
• /
• pp.44-50
• /
• 2006

This paper describs about the technique of ultra-precision machining for an infrared(IR) camera aspheric mirror. A 200 mm diameter aspheric mirror was fabricated by SPDTM(Single Point Diamond Turning Machine). Aluminum alloy as mirror substrates is known to be easily machined, but not polishable due to its ductility. Aspheric large reflector without a polishing process, the surface roughness of 5 nm Ra, and the form error of ${\lambda}/2\;({\lambda}=632.8\;nm)$ for reference curved surface 200 mm has been required. The purpose of this research is to find the optimum machining conditions for cutting reflector using Al6061-T651 and apply the SPDTM technique to the manufacturing of ultra precision optical components of Al-alloy aspheric reflector. The cutting force and the surface roughness are measured according to each cutting conditions feed rate, depth of cut and cutting speed, using diamond turning machine to perform cutting processing. As a result, the surface roughness is good when feed rate is 1mm/min, depth of cut $4{\mu}m$ and cutting speed is 220 m/min. We could machined the primary mirror for IR camera in diamond machine with a surface roughness within $0.483{\mu}m$ Rt on aspheric.

• Tunnel and Underground Space
• /
• v.4 no.2
• /
• pp.132-143
• /
• 1994

Many methods and techniques to reduce ground vibrations are well known. Some of them are to adopt electric millisecond detonators with a sequential blasting machine or an initiating system with an adequate number of delay intervals. The types of electric detonators manufactured in korea include instantaneous, decisecond and millisecond delays but numbers of delay intervals are only limited from No.1 to No.20 respectively. It is not sufficient to control accurately millisecond time with these detonators in tunnel excavation. Sequential fire time refers to adding an external time delay to a detonators norminal firing time to obtain sequential initiation and it is determined by sequential timer setting. To reduce the vibration level, sequential blasting machine(S.B.M) with decisecond detonators was adopted. A total of 134 blasts was recorede at various sites. Blast-to-structure distances ranged from 20.3 to 42.0 meter, where charge weight varied from 0.24 to 0.75 kg per delay. The results can be summarized as follow: 1. The effects of sequential blasting machine on the vibration level are discussed. The vibration level by S.B.M are decreased approximately 14.38~18.05% compare to level of conventional blasting and cycle time per round can be saved. 2. The empirical equations of particle velocity were obtained in S.B.M and conventional blasting. V=K(D/W1/3)-n, where the values for n and k are estimated to be 1.665 to 1.710 and 93.59 to 137 respectively. 3. The growth of cracks due to vibrations are found but the level fall to within allowable value.

• Journal of Environmental Impact Assessment
• /
• v.33 no.2
• /
• pp.74-83
• /
• 2024

This study aims to estimate roadkill occurrences and investigate influential factors in Chungcheongnam-do, contributing to the establishment of roadkill prevention measures. By comprehensively considering weather, road, and environmental information, machine learning was utilized to estimate roadkill incidents and analyze the importance of each variable, deriving primary influencing factors. The Gradient Boosting Machine (GBM) exhibited the best performance, achieving an accuracy of 92.0%, a recall of 84.6%, an F1-score of 89.2%, and an AUC of 0.907. The key factors affecting roadkill included average local atmospheric pressure (hPa), average ground temperature (℃), month, average dew point temperature (℃), presence of median barriers, and average wind speed (m/s). These findings are anticipated to contribute to roadkill prevention strategies and enhance traffic safety, playing a crucial role in maintaining a balance between ecosystems and road development.

• Journal of the Korean Society for Precision Engineering
• /
• v.18 no.3
• /
• pp.61-67
• /
• 2001

The finishing process for die is an important process because it has influence on final quality of products. Recently s study on development of 5-axis die automated finishing machine has been progressed. But die must be moved from the cutting machine to the die automated finishing machine. So manufacturing cost and time increase and machining error occurs by transfer. So, in this study, a 3-axis machining center was applied to die finishing. Because cutting tool can be changed to finishing tool by ATC, both of cutting and finishing process are possible on the machine. However, this application results in the decrease of finishing for the improvement of form accuracy. So this study focused on the generation of finishing tool path suitable to 3-axis die finishing for the improvement of form accuracy. The form accuracy evaluation is performed by the measurement of removal depth using a stylus profilometer. From the result, it is confirmed that form accuracy was improved less than 2$\mu$m of removal depth error.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2005.06a
• /
• pp.309-312
• /
• 2005

DTM (Diamond Turning Machine) is using for ultra precision manufacturing such as, plastic lens die or aspherical optics. This study is on a design of precision 2-axis stage for DTM. We designed and manufactured a back lash free stage using different weights and measured the positioning accuracy using Interferometer. Also, the 2-D moving accuracy is measured using the high magnification CCD technique. Then, the stage is tested with the machining of spherical and aspherical lens in a DTM with air bearing spindle. It was shown that the back lash free stage is effective for improving the positioning accuracy. Also, positioning control errors in motion control board were able to be found using the proposed stages system.

• Tribology and Lubricants
• /
• v.15 no.2
• /
• pp.131-140
• /
• 1999

This study dealt with some problems occurred in spectrometric oil analysis that has been popularly used for a machine condition monitoring in various fields of industry. One of the problems is that spectrometric technique could not analyze contaminants of large particle (larger than 10 $\mu\textrm{m}$) in lubricating oils. This limitation caused a serious problem in analyzing lubricated machine conditions since wear debris of large size represents better critical machine conditions. In this work, this problem was found to be solved by using a filtration method prior to spectrometric analysis. Another problem could be that spectrometric analysis is incapable of identifying contaminants. This nay mislead the result seriously in practice. This problem was surveyed by analyzing both various types of industrial lubricants and laboratory simulation tests, and the solutions to the problem were suggested in this work.