• Korean Journal of Agricultural Science
• /
• v.3 no.1
• /
• pp.95-104
• /
• 1976

This study was conducted to test the harvesting operation of two kinds of rice varieties such as Milyang #15 and Tong-il with a imported two furrow Japanese combine and was performed to find out the operational accuracy of it, the adaptability of this machine, and the feasibility of supplying this machine to rural area in Korea. The results obtained in this study are summarized as follows; 1. The harvesting test of the Milyang #15 was carried out 5 times from the optimum harvesting operation was good regardless of its maturity. The field grain loss ratio and the rate of unthreshed paddy were all about 1 percent. 2. The field grain loss of Tong-il harvested was increased from 5.13% to 10.34% along its maturity as shown in Fig 1. In considering this, it was needed that the combine mechanism should be improved mechanically for harvesting of Tong-il rice variety. 3. The rate of unthreshed paddy of Tong-il rice variety of which stem was short was average 1.6 percent, because the sample combine used in this study was developed on basisof the long stem variety in Japan, therefore some ears owing to the uneven stem of Tong-il rice could nat reach the teeth of the threshing drum. 4. The cracking rates of brown rice depending mostly upon the revolution speed of the threshing drum(240-350 rpm) in harvesting of Tong-il and Milyang #15 were all below 1 percent, and there was no significance between two varieties. 5. Since the ears of Tong-il rice variety covered with its leaves, a lots of trashes was produced, especially when threshed in raw materials, and the cleaning and the trashout mechanisms were clogged with those trashes very often, and so these two mechanisms were needed for being improved. 6. The sample combine of which track pressure was $0.19kg/cm^2$ could drive on the soft ground of which sinking was even 25cm as shown in Fig 3. But in considering the reaping height adjustment, 5cm sinking may be afford to drive the combine on the irregular sinking level ground without any readjustment of the resaping height. 7. The harvesting expenses per ha. by the sample combine of which annual coverage area is 4.7 ha. under conditions that the yearly workable days is 40, percentage of days being good for harvesting operation is 60%, field efficiency is 56%, working speed is 0.273m/sec, and daily workable hours is 8 hrs is reasonable to spread this combine to rural area in Korea, comparing to the expenses by the conventional harvesting expenses, if mechanical improvement is supplemented so as to harvest Tong-il rice. 8. In order to harvest Tong-il rice, the two furrow combine should be needed some mechanical improvements that divider can control not to touch ears of paddy, the space between the feeding chain and the thrshing drum is reduced, trash treatment apparatus must be improved, fore and rear adjust-interval is enlarged, and width of track must be enlarged so as to drive on the soft ground.

• Journal of Fashion Business
• /
• v.13 no.6
• /
• pp.61-75
• /
• 2009

The objective of this research is to the enhance the color function of work clothing : to research and analyze the hue and tone of work clothing colors to be used for machinery and heavy industries in national industrial complexes, Through this research, the color using problems which related with safety workers will be revealed. For this project, total 42 sets of work suits were sampled from 12 different companies in the machinery and construction industries in the national industrial complexes of Gyeongsang Namdo Province and 16 sets of work suits currently being sold in the market. The collected work suits samples were classified according to item types and design. Color measurements were taken thus: After calibration according to ASTM D1729 specifications of standardized configuration settings to match standardized luminous source D65(Daylight 6500K) in color cabinet BOTECK SuperLight-VI, the RGB values of the work suits were calculated using PANTONE Color Cue TX. The RGB values of the colors thus derived were converted into V/C values using the Munsell Conversion 9.0.6 and analyzed with Munsell's 10-color system and PCCS. The results were presented according to Munsell's color wheel and color and brightness distributions were expressed in table form, as well as presented as a tone map. Following analysis, color hue distribution was found to be concentrated around PB, and brightness distribution toward the low end and mid range of the scale. Saturation values were distributed mostly around the low end of the scale. Following color tone analysis according to PCCS, it became apparent that colors were mainly distributed around dkg, ltg, and g, at low- and mid-brightness and low-saturation. Therefore, it may be concluded that colors used in work suits in the machinery and heavy industries are mainly cool colors, at low- and mid-brightness and low saturation. It is conjectured that such colors were applied uniformly in the workplace in order to serve certain functions, such as concealment of stains and contamination. Therefore, it follows that the utilization of colors, among other functions served by working clothings, must be taken into consideration in order to enhance safety and efficiency.

• 한국HCI학회:학술대회논문집
• /
• 2006.02a
• /
• pp.355-361
• /
• 2006

In large scale environments like airport, museum, large warehouse and department store, autonomous mobile robots will play an important role in security and surveillance tasks. Robotic security guards will give the surveyed information of large scale environments and communicate with human operator with that kind of data such as if there is an object or not and a window is open. Both for visualization of information and as human machine interface for remote control, a 3D model can give much more useful information than the typical 2D maps used in many robotic applications today. It is easier to understandable and makes user feel like being in a location of robot so that user could interact with robot more naturally in a remote circumstance and see structures such as windows and doors that cannot be seen in a 2D model. In this paper we present our simple and easy to use method to obtain a 3D textured model. For expression of reality, we need to integrate the 3D models and real scenes. Most of other cases of 3D modeling method consist of two data acquisition devices. One for getting a 3D model and another for obtaining realistic textures. In this case, the former device would be 2D laser range-finder and the latter device would be common camera. Our algorithm consists of building a measurement-based 2D metric map which is acquired by laser range-finder, texture acquisition/stitching and texture-mapping to corresponding 3D model. The algorithm is implemented with laser sensor for obtaining 2D/3D metric map and two cameras for gathering texture. Our geometric 3D model consists of planes that model the floor and walls. The geometry of the planes is extracted from the 2D metric map data. Textures for the floor and walls are generated from the images captured by two 1394 cameras which have wide Field of View angle. Image stitching and image cutting process is used to generate textured images for corresponding with a 3D model. The algorithm is applied to 2 cases which are corridor and space that has the four wall like room of building. The generated 3D map model of indoor environment is shown with VRML format and can be viewed in a web browser with a VRML plug-in. The proposed algorithm can be applied to 3D model-based remote surveillance system through WWW.

• KIPS Transactions on Computer and Communication Systems
• /
• v.9 no.10
• /
• pp.239-246
• /
• 2020

In the medical field where artificial intelligence technology is introduced, research related to clinical decision support system(CDSS) in relation to diagnosis and prediction is actively being conducted. In particular, medical imaging-based disease diagnosis area applied AI technologies at various products. However, medical imaging data consists of inconsistent data, and it is a reality that it takes considerable time to prepare and use it for research. This paper describes a one-stop AI learning platform for converting to medical image standard R_CDM(Radiology Common Data Model) and supporting AI algorithm development research based on the dataset. To this, the focus is on linking with the existing CDM(common data model) and model the system, including the schema of the medical imaging standard model and report information for multi-center research based on DICOM(Digital Imaging and Communications in Medicine) tag information. And also, we show the execution results based on generated datasets through the AI learning platform. As a proposed platform, it is expected to be used for various image-based artificial intelligence researches.

• The Journal of Korean Academy of Prosthodontics
• /
• v.55 no.3
• /
• pp.264-271
• /
• 2017

Purpose: The purpose of this study is to investigate the differences in bond strength of four different indirect composites to the gold alloy and Ni-Cr alloy according to type of metal surface treatment after water storage. Materials and methods: Type IV gold alloy and Ni-Cr alloy were used for casting alloy while four types of indirect composite resins (Gradia, Tescera Sinfony and in;joy) were used in this study. Metal specimens were produced by casting and total of 240 specimens (60 specimens per one indirect composite group) were prepared. After bonding indirect composite resin and undergoing 24 hours of polymerization, customized jig was attached to the metal specimen and shear bond strength were measured using universal testing machine. Also, differences in shear bond strength before and after water storage for 240 hours were also measured. Results: In the measurement of shear bond strength according to the metal surface treatments, bead group showed high strength followed by loop and flatting group (P<.05). After being stored in water bath for 240 hours, Gradia showed statistically significant high bond strength compared to other indirect composite resins in all groups (P<.05). Conclusion: Shearbond strength was found to be different according to type of metal surface treatment and type of metal used after storage in water. Further studies need to be developed for clinical practices as three are still problems of microleakage, stain or wear.

• Journal of Food Hygiene and Safety
• /
• v.34 no.6
• /
• pp.571-575
• /
• 2019

Fungal occurrence during production of dried red pepper was investigated using red pepper samples collected at harvest, before and after washing, and before, during or after drying. Fungal incidence was evaluated by counting the number of fungal colonies grown after incubating random pepper cuts on potato dextrose agar plates. Washing with ground water had no significant effect on reduction of fungal contamination. Fungal increase was observed in some samples, and the insides of washer and containers were contaminated with fungi. Drying caused significant fungal increase regardless of drying method although the fungal incidence after machine drying was lower than that after greenhouse drying. Fungal increase was observed in the samples being dried in a greenhouse and some mycotoxigenic species were also detected. Therefore, the most important control point for fungal contamination during dried pepper production appears to be the drying process, especially in a greenhouse.

• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.5 no.4
• /
• pp.309-322
• /
• 2007

This study deals with the irradiation effects on some selected components which are being used in an Advanced Spent Fuel Conditioning Process (ACP). Irradiation test components have a higher priority from the aspect of their reliability because their degradation or failure is able to critically affect the performance of an ACP equipment. Components that we chose for the irradiation tests were the AC servo motor, potentiometer, thermocouples, accelerometer and CCD camera. ACP facility has a number of AC servo motors to move the joints of a manipulator and to operate process equipment. Potentiometers are used for a measurement of several joint angles in a manipulator. Thermocouples are used for a temperature measurement in an electrolytic reduction reactor, a vol-oxidation reactor and a molten salt transfer line. An accelerometer is installed in a slitting machine to forecast an incipient failure during a slitting process. A small CCD camera is used for an in-situ vision monitoring between ACP campaigns. We made use of a gamma-irradiation facility with cobalt-60 source for an irradiation test on the above components because gamma rays from among various radioactive rays are the most significant for electric, electronic and robotic components. Irradiation tests were carried out for enough long time for total doses to be over expected threshold values. Other components except the CCD camera showed a very high radiation hardening characteristic. Characteristic changes at different total doses were investigated and threshold values to warrant at least their performance without a deterioration were evaluated as a result of the irradiation tests.

• Journal of the Korean Ceramic Society
• /
• v.39 no.1
• /
• pp.57-67
• /
• 2002

The effect of $\beta$-TCP and PHA as additives on initial setting time, compressive strength and surface micro-structure after in vitro test of bone cement in TTCP and DCPA system was investigated. The median particle sizes of TTCP, $\beta$-TCP, DCPA and PHA for bone cement were about 3, 5, 0.9 and 4${\mu}{\textrm}{m}$, respectively. Initial setting time and compressive strength of bone cement with various composition was measured by Vicat test and Universal Testing Machine, and surface morphology and crystalline phases of bone cements were observed and analyzed by SEM and x-ray diffractometer. Initial setting time was not affected by composition but by powder/liquid ratio, and cement with PHA required double amount of solution for paste as much as one without PHA, especially. It was thought that $\beta$-TCP and PHA in bone cements was not related to setting reaction. Thus, the addition of $\beta$-TCP and PHA in bone cements decreased compressive strength and inhabited HAP from being produced on surface in vitro test. In conclusion, it was not expected that $\beta$-TCP and PHA in TTCP-DCPD bone cements enhanced the strength and bioacitivity.

• Journal of The Korean Association of Information Education
• /
• v.24 no.4
• /
• pp.313-325
• /
• 2020

There is a growing interest and need for the educational use of artificial intelligence as artificial intelligence technologies such as machine learning and deep learning, the core technologies of the intelligent information society, owing to the recent innovative technological advances. Consequently, the Ministry of Education announced the First Information Education Comprehensive Plan for introducing artificial intelligence competence enhancing education into the education field in preparation for the intelligent information society based on artificial intelligence technologies. Therefore, this study collected 416 overseas papers related to the educational use of artificial intelligence from the Web of Science (WoS) in order to explore the potential for using artificial intelligence educationally. This study analyzed the research status and research topic by country, citation counts, network analysis on keywords of the collected data by using the bibliometrix package of R program. Through this, it was possible to identify the research trend on the educational use of artificial intelligence, currently being conducted in foreign countries. It is believed that it will be possible to obtain implications for the topics and directions to be studied in the information education for strengthening artificial intelligence education based on the results of this study.

• Journal of Chest Surgery
• /
• v.9 no.2
• /
• pp.239-244
• /
• 1976

Alterations in the serum magnesium level were studied in twenty patients who had open-heart surgery during the period from August 1974 to May 1975. The patients were chosen at random. The operative procedures included repair for congenital heart diseases in fifteen patients and cardiac valve replacement for acquired valvular heart diseases in five patients. The age ranged from 8 to 46 years, with an average of 19 years. None of the patients had a history of gross neuromuscular abnormalities. Cardiopulmonary bypass was carried out using a roller pump and a disposable oxygenator. The prime solution consisted of 2 units of ACD banked blood and approximately an equal volume of non-blood additives in adults, while a relatively smaller volume was added in children. The average flow rate was 2,733 ml per minute. Blood samples for magnesium and arterial blood pH were obtained the day after admission 25 minutes after initiation of the bypass and on the morning the day after operation. Preoperative data were then compared with those obtained during the bypass and postoperatively by a paired test. During the bypass, the serum magnesium level decreased significantly from $1.425{\pm}0.029$ to $1.210{\pm}0.063mEq.$ liter (p<0.001). Also, there was a significant decrease in serum magnesium from $1.425{\pm}0.029$ preoperatively to $1.255{\pm}0.083mEq$. per liter (p<0.001). Also, there was a significant decrease in serum magnesium from $1.425{\pm}0.029$ preoperatively to $1.255{\pm}0.083mEq$. per liter postoperatively (p<0.01). The duration of bypass was less than 90 minutes in 10 patients (group A) and exceeded 90 minutes in the remaining 10 (group B). There was no statistical correlation between the groups A and B ($p{\gg}0.20$). Statistical analyses of the serum magnesium level and arterial blood pH showed no significant correlation with correlation coefficient; being -0.3485(pre-op), -0.2971(during bypass), and -0.1008(post-op), respectively. In all the patients, no gross neuromuscular abnormalities were found postoperatively. At present, the clinical significance of the serum magnesium level during and after bypass is controversial. In the near future, however, it is expected that improvements in prime solution and heart-lung machine will solve this problem.