• 한국정밀공학회지
• /
• 제12권9호
• /
• pp.5-21
• /
• 1995

공작기계의 가공 정밀도에 영향을 주는 주요 요인은 정적특성(Static behavior), 동적특성(Dynamic behavior), 그리고 열적특성(Thermal behavior)에 있다는 것은 이미 언급한 바 있다. 열적영향으로 인한 정밀도를 안정시키는 완전한 해결책은 아직 발견되지 못하고 있다. 그 이유는 공작기계 자체뿐만 아니라 부품들이 복잡하고 공작기계의 내부, 기계와 주위환경사이에 복잡한 열적상호작용이 존재하고 있기 때문이다. 그럼에도 불구하고 공작기계에는 더욱 높은 생산능력과 가공정도에 대한 요구가 점점 커지고 있다. 과거 40년 간에 걸쳐 공작기계의 열적거동에 대한 연구가 활발히 진행되어 왔지만 일반적으로 적용하여 만족할 만한 열적 불안정의 해결책은 아직 나오지 않고 있으며 단지 여러가지의 기계구성요소, 즉 Spindle, Column이나 Bed와 같은 본체의 구조나 Table이나 Slide에 대해서 열적 최적화를 얻는 노력이 집중적으로 행해지고 있다. 공작기계 의 열변형에 대한 연구는 1950년대부터 시작되었으며, 선반이나 연삭기의 열변형 측정기술과 해당하는 설계변경 방법 그리고 냉각을 함으로서 열적 불안정을 극복시키는 방법이 주요 연구과제였으나 1960년대 후반에는 구성 요소의 온도분포와 열의 흐름에 관한 수학적 모델을 한들어 해석적 수법올 열적 거동의 연구가 행하여졌었다.

• 한국안전학회지
• /
• 제18권1호
• /
• pp.44-49
• /
• 2003

Permanent magnet synchronous motor(PMSM) is widely used in many applications such as an electric vehicle. compressor drives of air conditioner and machine tool spindle drives. PMSM drive system have become a popular choice in various application, due to their excellent power to weight ratio. This paper is proposed maximum torque control for field weakening operation of PMSM drive. At low speeds, the reluctance torque is used to maximize the output for a given current level. This is achieved maximum torque per ampere(MTPA) by selecting an optimal value of the direct stator current component. At high speeds, the system reaches a point at which the inverter will not be able to supply the desired voltage. In this case it is necessary to make use of an increased value the direct current component. The proposed control algorithm is applied to PMSM drive system, the operating characteristics controlled by maximum torque control are examined in detail by simulation.

• 한국공작기계학회논문집
• /
• 제13권4호
• /
• pp.1-8
• /
• 2004

Various controllable parameters of an experiment have influence on grinding process. In order to get good products with a high quality, these parameters should be considered whether each parameter has relations to the quality. This paper describes the use of the design of experiments to minimize geometric error in surface grinding. Controllable parameters for the design of experiments were selected as spindle speed, table speed, depth of cut and grain size. From the experimental results, a degree of influence between these parameters and the geometric error was evaluated. An optimal set of grinding conditions was obtained by means of analysis of variance(ANOVA).

• 한국기계가공학회지
• /
• 제11권3호
• /
• pp.110-115
• /
• 2012

For domestic aircraft industry, not mass production of components is limited, small production scale of the order is made by part because many kinds of hundreds of thousands of kinds of small quantity batch production system are taking. But the high reliability and stability are required during the processing because they require high precision parts are required. It is found that when C-axis rotation speed was increased, the diameter of the cutting tool decreased with increasing surface roughness, while the turn-mail feed rate was increased with increasing the surface roughness.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2001년도 춘계학술대회 논문집(한국공작기계학회)
• /
• pp.352-357
• /
• 2001

In this study, residual stress was investigated to evaluate damaged layer in high speed machining through simulation. In machining steel(STDll), residual stress remaining in machined surface was mainly appeared as compressive stress. The scale of this damaged layer more depends on feed per tooth and radial depth than spindle speed. Damaged layer was measured by optical microscope and hardness method. The micro-structure of damaged layer was a martensite because of cutting force and cutting temperature. Thickness of damaged layer is increased with incresing of feed per tooth and radial depth.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2003년도 추계학술대회
• /
• pp.324-328
• /
• 2003

The Magnetoeheological fluid has the properties that it's viscosity has dramastic changed under some magnetic fields therefore, Magnetorhlogical fluids has been used for micro polishing of the micro part( for example, a aspherical surface in a micro lens). The polishing process may appears as follows. A part rotating on the spindle is brought into contact with an Magnetorhological finshing(MRF) fluids which is set in motion by the moving wall. In the region where the part and the MRF fulid ate brought into contact, the applied magnetic field creates the conditions necessary for the material removal from the part surface. The material removal takes place in a certain region contacting the surface of the part which can be called the polishing spot or zone. The polishing mechanism of the material removal in the contact zone is considered as a process governed by the particularities of the Bingham flow in the contact zone. Resonable calculated and experimental magnitudes of the material removal rate f3r glass polishing lends support the validity of the approach.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1997년도 추계학술대회 논문집
• /
• pp.56-59
• /
• 1997

The recent machine tools are requested so high-quality processing and productivity increasing. Therefore it is so necessary to develop technology for high-speed and high-precision. This thesis touches on the development of high speed and intellectual line center. At first, the line center is necessary that strong structure, compact structure an light weight design for high-speed processing and transfer. So. It is necessary that examination of new materials and structures for light-weight and control devices for precision processing. So. it si going to make mention of the process of 1st model production for the above-mentioned base on test model production and evaluation.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2003년도 춘계학술대회 논문집
• /
• pp.542-546
• /
• 2003

This paper describes the machining characteristics of a developed micro grooving machine. Experiments have been conducted on the various grooving condition such as spindle revolution speed, feed rates and depth of groove. V and U-shaped blade tool and STD11 workpiece was used in this study. Evaluating the machining conditions, RMS and frequency spectrum analysis of AE(acoustic emission) signals according to each conditions were applied. As a result, this study presented the process to optimize micro grooving condition and possibility of application of AE technique in groove machining.

• 한국공작기계학회논문집
• /
• 제10권1호
• /
• pp.88-93
• /
• 2001

Carbon fiber epoxy composite are widely used in airframe structures, space vehicles, sports equipment, and high speed reciprocating parts for industrial machinery. In this paper, the groove processing characteristics of carbon fiber epoxy com-posite was experimentally investigated in order to study the endmill operation of fiber reinforce epoxy composites. Followings are main finding from the experimental results. First, the cutting and bending force in groove processing of the carbon fiber epoxy composite increased as the spindle speed deceased. They also deceased as the table feed increased. Second, the good cutting status obtained at the entrance of groove while delamination occurred at the exit of groove, Third, the regular high speed steel endmill was not efficient, thus the new endmill such as coated carbide rooter endmill or dia-mode endmill should be used for the effective endmll operation of carbon filber epoxy composites.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2003년도 춘계학술대회 논문집
• /
• pp.39-44
• /
• 2003

It was shown that the robustness of deterministic observers with respect to modeling errors, measurement bias and round-off errors can be represented by a single performance index the condition number of the observer eigenvector matrix. In this paper, a robust observer for multi-output systems is designed using the left eigenstructure assignment, where the observer gain can not be determined uniquely with respect to the desired observer poles. Utilizing the eigenstructuer assignment for the robustness of the observer, the desired eigenvector matrix is selected to achieve the observer eigenvector matrix with the small condition number. The performance of the designed robust observer is evaluated in a spindle-drive simulation example where the load speed to be estimated based on the measured signals.