• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2002.10a
• /
• pp.429-435
• /
• 2002

In order to manufacture a precision mold/die by machining, users need high speed & precision mold/die machining center. So, for development of this machine, we intend to use linear motor that is instead of ball-screw, servo-motor and coupling, high-speed spindle of pressurized air journal bearing and composite materials. In this paper we research column moving type and table moving type. The former is mainly piling 3 axes on one moving body, the latter is consist of two independent carriages. Both types are available to high speed & precision machine, but we finally draw a conclusion column moving type due to an advantage of high-speed control of linear motor.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.17 no.5
• /
• pp.70-75
• /
• 2008

This paper describes a tool-clamping/unclamping mechanism for application of a micro-spindle. The mechanism is based on one-way shape memory effect and interference-fit. The corresponding mathematical models and a few considerable design parameters are mentioned in this paper. Especially, necessary conditions for the clamping and unclamping operation are investigated through finite element analysis. The analysis results show that the differences between the diametral deformations of the tool holder in high temperature and that in low temperature are increased according to amounts of the interference. Thus the less interference between the tool-holder and the ring, the less tolerance to allow the clamping and unclamping operation because the inner diameter of the tool holder in high temperature should be smaller than the diameter of the tool shank, and that in low temperature should be larger than the diameter of the tool shank. In addition, the design for maximization of clamping force are investigated based on finite element analysis. The results show that the more amounts of the interference, the more clamping force. As the result, the interference should be considered as a important factor to maximize the tool clamping force.

• Journal of the Korean Society for Precision Engineering
• /
• v.31 no.7
• /
• pp.569-576
• /
• 2014

Sensor node means a device to include sensor, amplifier, and data acquisition (DAQ) equipment. The sensor converts physical signals to electric signals and weak signals from the sensor can be amplified through the amplifier. DAQ equipment converts analog signal to digital signal and collects converted digital signal. Since the sensor node is sensitive to the environment so that selection of mounting position and fixture design of sensor are applied differently depending on the characteristics of a target. This study is about designing and manufacturing sensor node to be used in a machine tool. The environment of machine tool is very severe due to noise, temperature fluctuation, and dust, etc. Hence, the sensor and amplifier must be designed and manufactured by considering the environmental issues. The designed and manufactured sensor node was tested for the reliability and effectiveness of the developed sensor nodes in the study.

• Journal of the Korean Society for Precision Engineering
• /
• v.26 no.5
• /
• pp.135-141
• /
• 2009

The bearing clearance is influenced by shrink fit and thermal expansion during operation. The designer must take into account the reduction of clearance after installation to the interference fits, and thermal expansion must be considered. The purpose of this study is to grasp the internal clearance variation and behavior of a bearing which is a deep connected with fatigue life of bearing and performance of spindle through FEM(Finite Element Method). Finite element analysis is performed by using commercial code ANSYS according to variation of thermal condition and rotational speeds. This paper presents correct negative internal clearance according to temperature during operation. Furthermore, interrelation between thermal expansion and contraction are presented to maintain adequate contact force for three type of spindle system (HSK-A60, HSK-40E, HSK-32E). The influence of the centrifugal force and Internal clearance variation of bearing is studied to operating rotational speed.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2005.10a
• /
• pp.370-374
• /
• 2005

This study deals with the method of post-processing in the automatic tool path generation for 5-axis NC machining. The 5-axis NC machining cannot only cope with the manufacturing of complicated shapes, but also offers numerous advantages such as reasonable tool employment, great reduction of set-up process and so on. Thus 5-axis NC machining has been used fur aircraft parts, mold and die as well as for complicated shapes such as impeller, propeller and rotor. However, most of the present CAM systems for 5-axis NC machining have limited functions in terms of tool collision, machine limits and post-processing. Especially 5-axis machine configurations are various according to the method which the rotational axes are adapted with the table and spindle. For that reason, in many cases the optimal numerical control (NC) data cannot be obtained or considerable time is consumed. To solve this problem, we applied a general post-processor fur 5-axis NC machining. The validity of this post-processor should be experimentally confirmed by successfully milling to a helix shaped workpiece.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2002.04a
• /
• pp.209-214
• /
• 2002

Mechanical micro-engineering is an easy and cheap way to fabricate micro-structures. If the application of the conventional machining method using flat-end mill becomes available for the micro-manufacturing process, it will be advanced as an extension of the conventional machining process. In this study, micro-grooves cutting using flat-end mill(($\phi$8) was performed. The characteristics on flat-end milling was investigated to improve machinability of micro-grooves. The experiments were performed according to variations of spindle revolution, depth of cut, and feed rate. Machinability through various cutting conditions was evaluated by surface geometry, tool wear, and cutting force. The results show that micro V-grooves of width(pitch) 29${\mu}{\textrm}{m}$ were acquired by flat-end milling. The maximum and minimum roughness of the wall of grooves was 438 and 67nm, respectively

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1993.10a
• /
• pp.389-394
• /
• 1993

Die making process is classified into design,manufacturing,polishing,assembly, and performance test. Die polishing is not a machining process by cutting edge of tool, but it is finishing by relative cutting movement under the surface contact between grinding particles and workpiece, and this process comprised 30~40% of total manufacturing hours. However, die polishing process is still performed by the skilled workers. Now a days, it is very difficult to secure skilled workers due to the hardworking environment and this situation will be getting worse in the future which has great difficulty of dies and molds industries.This process has the common problem on the elimination of tedious manual polishing among the tool making industries. Therefore this study is aimed at the development of an automatic polishing attachment which could be attached onthe spindle of CNC machine tool and controlled by the NC program data created by CAD/CAM system. As a result, this study will contribute the realization of automatic fine polishing process and improvement of quality level of dies and molds.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1992.10a
• /
• pp.47-51
• /
• 1992

Automatic detection of tool breakage during NC machining is a key issue not only for improving productivity but to implement the unattended manufacturing system. In this paper, we develop a vibration sensor-based tool breakage detection system for NC milling processes. The system obtains the time-domain vibration signal from the sensor attached on the spindle bracket of our CNC machine and declares tool failures through the on-line monitoring schemes. For on-line detection, our approach is to use the PSC(statistical process control) methods being increasingly used for on-line process control. The main thrust of this paper is to propose and compare the performance of SPC methods including : a) X-bar control scheme, b) S control scheme, c)EWMA (exponentially weighted moving average) scheme, and d) AEWMA (adaptive exponentially weighted moving average) scheme. The performance of the control schemes are compared in terms of the type 1 and 2 error calculated from the experiment data.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2001.10a
• /
• pp.214-219
• /
• 2001

One of the major limitations of productivity and quality in metal cutting is the machining accuracy of machine tools. The machining accuracy is affected by geometric errors, thermally-induced errors, and the deterioration of the machine tools. Geometric and thermal errors of machine tools should be measured and compensated to manufacture high quality products. In metal cutting, the machining accuracy is more affected by thermal errors than by geometric errors. In this study, the compensation device and temperature-based algorithm have been presented in order to compensate thermal error of machine tools under the real-time. The thermal error is modeled by means of angularity errors of a column and thermal drift error of the spindle unit which are measured by the touch probe unit with a star type styluses, a designed spherical ball artifact, and five gap sensors. In order to compensate thermal characteristics under several operating conditions, experiments performed with five gap sensors and manufactured compensation device on the horizontal machining center.

• Journal of Korean Society of Industrial and Systems Engineering
• /
• v.43 no.4
• /
• pp.161-167
• /
• 2020

In the process of cutting large aircraft parts, the tool may be abnormally worn or damaged due to various factors such as mechanical vibration, disturbances such as chips, and physical properties of the workpiece, which may result in deterioration of the surface quality of the workpiece. Because workpieces used for large aircrafts parts are expensive and require strict processing quality, a maintenance plan is required to minimize the deterioration of the workpiece quality that can be caused by unexpected abnormalities of the tool and take maintenance measures at an earlier stage that does not adversely affect the machining. In this paper, we propose a method to indirectly monitor the tool condition that can affect the machining quality of large aircraft parts through real-time monitoring of the current signal applied to the spindle motor during machining by comparing whether the monitored current shows an abnormal pattern during actual machining by using this as a reference pattern. First, 30 types of tools are used for machining large aircraft parts, and three tools with relatively frequent breakages among these tools were selected as monitoring targets by reflecting the opinions of processing experts in the field. Second, when creating the CNC machining program, the M code, which is a CNC auxiliary function, is inserted at the starting and ending positions of the tool to be monitored using the editing tool, so that monitoring start and end times can be notified. Third, the monitoring program was run with the M code signal notified from the CNC controller by using the DAQ (Data Acquisition) device, and the machine learning algorithms for detecting abnormality of the current signal received in real time could be used to determine whether there was an abnormality. Fourth, through the implementation of the prototype system, the feasibility of the method proposed in this paper was shown and verified through an actual example.