• Smart Structures and Systems
• /
• v.12 no.5
• /
• pp.579-594
• /
• 2013

A new enthalpy - based procedure for the homogenization of the electromechanical material parameters of composite piezoelectric modules with integrated electrodes is presented. It is based on a finite element (FE) modeling of the latter's representative volume element (RVE). In contrast to most previously published homogenization approaches that are based on averaged quantities, the presented method uses a direct evaluation of the electromechanical enthalpy. Hence, for the linear orthotropic piezoelectric composite behavior full set of elastic, piezoelectric, and dielectric material parameters, 17 load cases (LC) are used where each load case leads directly to one material parameter. This gives the possibility to elaborate a very strict and easy to program processing. In conjunction with the 17 LC, the enthalpy - based homogenization is particularly suitable for laminated composite piezoelectric modules with integrated electrodes. In this case, the electric load has to be given at the electrodes rather than at the RVE FE model boundaries. The proposed procedure is validated through its comparison to literature available results on a classical 1-3 piezoelectric micro fiber (longitudinally polarized) reinforced composite and a $d_{15}$ shear piezoelectric macro-fiber (transversely polarized) composite module.

• Agricultural and Biosystems Engineering
• /
• v.1 no.1
• /
• pp.22-29
• /
• 2000

The development of bio-response feedback control system known as the speaking plant approach has been a challenging task for plant production engineers and scientists. In order to achieve the aim of developing such a bio-response feedback control system, the primary concern should be to develop a practical non-invasive technique for monitoring plant growth. Those who are skilled in raising plants can sense whether their plants are under adequate water conditions or not, for example, by merely observing minor color and tone changes before the plants wilt. Consequently, using machine vision, it may be possible to recognize changes in indices that describe plant conditions based on the appearance of growing plants. The interpretation of image information of plants may be based on image features extracted from the original pictorial image. In this study, the performance of a finite element retina was optimized by a genetic algorithm. The optimized finite element retina was evaluated based on the performance of neural plant growth monitor that requires input data given by the finite element retina.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.40 no.2
• /
• pp.130-139
• /
• 1998

The finite element analysis program should be prepared to deal with many of newly arising engineering problems. The sequential structured programming technique does not make a finite element method so flexible. So far, the object oriented programming technique was studied as an alternative programming paradigm. However, most of the research were in the state of the evaluation of the possibility and the applicability of the object oriented method for a finite element program. In this study, a practical object oriented finite element analysis program, OOFE_ JAVA was developed and the result of the analysis on a rectangular clamped plate was shown. The objects which compose the OOFE_JAVA were applied to several engineering problem without any modification and it was concluded that the object oriented technique was appropriate for the development of a complex and large engineering system. And a virtual machine which Java language is using can be loaded on any kinds of computer which has java interpreter regardless of the platform on which the OOFE_JAVA was developed.

• Proceedings of the KIEE Conference
• /
• 2002.11d
• /
• pp.97-99
• /
• 2002

3D Equivalent magnetic Circuit Network Method (EMCNM) is comparatively the easy way that analyzes 3D models of Electric Machine by using permeance as a distributive magnetic circuit parameter under the existing magnetic equivalent circuit method and Numerical Method. The existing 3D EMCNM could not correctly describe the shape of an analysis target when using rectangular shape element or fan shape element, so it made errors when calculating permeance. Therefore, this paper use the trapezoidal element contained rectangular element. This paper calculate the torque based on the maxwell stress tenser method when the airgap is one layer, three layers, and 5 layers, respectively.

• Journal of Power System Engineering
• /
• v.5 no.1
• /
• pp.104-109
• /
• 2001

The stress distributions of hydranlic actuator cylinder tube acting in uniform inner pressure were analysed by the boundary element method(BEM). STKM13C tube was utilized for machine structural purposes model, its inner radius was 100 mm and outer radius was 140 mm. Axial length was semi-infinite and the isoparametric element of BEM was used. Radial and tangential stresses are maximum(-20.3 MPa and 52 MPa) at the inner radius and the minimum at the outer radius of the hydraulic actuator cylinders for an industrial systems. Stress diminution ratio was about 0.6 MPa/mm. And then coincidence between the simulation techniques as exact results(Lame' equation) and finite element method(FEM) is found to be fairly good, showing that the proposed analysis by BEM is reliable.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.10 no.5
• /
• pp.85-95
• /
• 2001

This study proposed a technique for inverse problem, linear approximation of contact position and loading in single and double meshing of spiral bevel gear , using 2-dimension model considered near the tooth by root stress. Determine root stress is carried out far the gear tooth by finite element method and boundary element method. Boundary element discretization near contact point is carefully performed to keep high computational accuracy. And from those estimated results, the comparing estimate value with boundary element method value was discussed.

• Journal of Mechanical Science and Technology
• /
• v.17 no.6
• /
• pp.896-905
• /
• 2003

A linear motor has many advantages next to conventional feed mechanisms: high transitional speed and acceleration, high control performance, and good positioning accuracy at high speed. Through the omission of a power transfer element, the linear motor shows no wear and no backlash, has a long lifetime, and is easy to assemble. A disadvantage of the linear motor is low efficiency and resultant high-temperature rise in itself and neighboring structures during operation. This paper presents the thermal behavior of the linear motor as a feed mechanism in machine tools. To improve the thermal behavior, an insulation layer is used. By placing the insulation layer between the primary part and the machine table, both the temperature difference and the temperature fluctuation in the machine table due to a varying motor load are reduced.

• Journal of international Conference on Electrical Machines and Systems
• /
• v.3 no.2
• /
• pp.139-147
• /
• 2014

The paper presents a systematic comparison of four topologies of the interior permanent magnet machine (IPMM) designed for low speed applications. This comparative study investigates the suitability of the concentrated winding and distributed winding in the stator and the flat-shaped or V-shaped magnets in the rotor poles. The paper also studies the inductance characteristics of the designs using finite element analysis. Various steps taken to minimize the cogging torque and torque ripple in the studied machines were also discussed in details.

• Journal of Magnetics
• /
• v.21 no.3
• /
• pp.399-404
• /
• 2016

This paper presents a new permanent magnet (PM) assisted topology for a recently introduced brushless wound rotor synchronous machine (BL-WRSM) [1]. The BL-WRSM had a dual-inverter configuration for generating a composite magneto motive force (MMF) with a fundamental component and a subharmonic component. The subharmonic component of the MMF is used for brushless excitation of the rotor. In this paper, additional PMs were introduced on the rotor of the BL-WRSM, making it a hybrid BL-WRSM. We also discussed the flux weakening operation for the hybrid BL-WRSM. The hybrid BL-WRSM offered advantages for starting the machine and provided better performance under full-load conditions. The finite element method (FEM) was used to analyze the performance of the hybrid BL-WRSM, and we compared its performance with BL-WRSM. Finally, prototypes were built with and without the PM-assistance, and experiments were conducted to demonstrate their performance.

• Journal of the Korean Society of Industry Convergence
• /
• v.15 no.1
• /
• pp.37-42
• /
• 2012

Trends in semiconductor equipment industry are to reduce the cost of producing semiconductor, semiconductor process development, facility development, and the minimum investment in terms of cost and quality. Semiconductor equipments are being considered to review and development is proceeding at the same time. In the first part of the semiconductor assembly process, in which the importance of die bonding process is emerging, a wide leadframe type die bonding machine is demanded for productivity. Die bonding machine was designed through experiments and by trial and error. It costs a lot of time and financial burden. The purpose of this study is to solve these problems by using the CAE tool 3G. By using finite element method, thermal analysis of die bonding machine to the various widths leadframe die bonder machine rail is performed for design.