• 한국생산제조학회지
• /
• 제19권1호
• /
• pp.1-6
• /
• 2010

Inconel 718 alloy has been applied to high temperature, high load and corrosion resistant environments due to its superior properties. However, This alloy is a difficult-to-cut nickel-based superalloy and the chipping or notch wear is mainly generated on the cutting edge of the tool. In this study, the machinability of Inconel 718 is investigated to improve tool life under various cutting conditions with TiCN-based coated ball-end mills. The cutting conditions can be suggested to improve both the tool life and machined surface quality in Inconel 718 high speed machining.

• 한국정밀공학회지
• /
• 제24권2호
• /
• pp.33-40
• /
• 2007

In this study, presintered and full sintered low purity alumina ceramics were machined with various tools to clarify the effect of cutting fluid in machinability. The main conclusions obtained were as follows. When the presintered ceramics were wet machined with sintered diamond tool, the tool wear becomes extremely large, and higher cutting speed can be used than in the case of full sintered ceramics. The productivity of wet cutting with the sintered diamond tool is much higher than that of dry cutting. In the case of the CBN and ceramic tools, the tool wear were smaller at wet cutting than at dry cutting, especially exhibiting considerably larger grooved tool wear in wet cutting with ceramic tool.

• 한국생산제조학회지
• /
• 제21권5호
• /
• pp.848-854
• /
• 2012

SCM420 steel cutting gear to improve the durability is quenched. When quenching, increases surface hardness, a change of the physical properties and machinability or fall. This study, using a solid carbide hobs skiving hobbing gear cutting finishing. And cutting tool solid carbide TiAlN coating hove when TiAlN coating on the surface of multi-con polishing hob conducted aero lap nano polishing for each cutting. Experimental results conducted aero lap nano coating on the surface polishing tool machinability was excellent. And aero lap nano polishing tool results were reduced 2.5 times the tool wear compared to TiAlN coated tools. Excellent results were 1.42 times longer tool life.

• 한국생산제조학회지
• /
• 제21권6호
• /
• pp.982-987
• /
• 2012

Inconel 718 alloy has been widely used in the aerospace, heavy industry and electronic industry. However, the machinability of this alloy is very poor, which is attributed to their inherent high strength that is maintained at elevated temperatures. The tool life is dominant problem in machining difficult-to-cut materials, so it is necessary to select the efficient cutting conditions for the improvement of tool life. In this study, the cutting force, tool wear and surface roughness are investigated in end milling machining under various cutting conditions. By this experiment, the efficient machining condition of this alloy is suggested to adopt in various industries.

• 한국분말재료학회지
• /
• 제20권4호
• /
• pp.285-290
• /
• 2013

$Ti_2AlN$ composites are a laminated compounds that posses unique combination of typical ceramic properties and typical metallic(Ti alloy) properties. In this paper, the powder synthesis, SPS sintering, composite characteristics and machinability evaluation were systematically conducted. The random orientation characteristics and good crystallization of the $Ti_2AlN$ phase are observed. The electrical and thermal conductivity of $Ti_2AlN$ is higher than that of Ti6242 alloy. A machining test was carried out to compare the effect of material properties on micro electrical discharge drilling for $Ti_2AlN$ composite and Ti6242 alloy. Also, mixture table as a kind of tables of orthogonal arrays was used to know how parameter is main effective at experimental design. Consequently, hybrid $Ti_2AlN$ ceramic composites showed good machining time and electrode wear shape under micro ED-drilling process. This conclusion proves the feasibility in the industrial applications.

• 한국정밀공학회지
• /
• 제18권2호
• /
• pp.84-89
• /
• 2001

In recent years, there is increasing demand of esthetic design and complex function in aerospace, automobile and die/mold industry, which brings into limelight high-precision, high-efficient machining of sculptured surface. This paper deals with the establishment of the optimal tool path on free form surface in high speed ball end milling. Ball end milling is widely used for free form surface die and mold. In this machining, the cutting direction was changed with tool path. The cutting characteristics, such as cutting force and surface form are varied according to the variation of cutting directions. In this paper, the optimal tool path with down cutting in free form surface cutting is suggested.

• 한국기계가공학회지
• /
• 제18권2호
• /
• pp.96-101
• /
• 2019

This paper presents a machinability evaluation of Inconel 718 material when using a new uniform-temperature indirect cooling method that incorporates constant-pressure liquid nitrogen (LN2). The flank wear of a TiAlN coated tool used with this indirect cooling system was much lower than that of the tool used with dry machining under all machining conditions. Also, the surface roughness resulting from machining with this indirect method was far less than that of a dry machined surface after the same cutting time. Reduced heat generation and uniform temperature in turning operations play important roles in tool life and surface quality.

• Steel and Composite Structures
• /
• 제34권5호
• /
• pp.681-698
• /
• 2020

The paper addresses contribution to the modeling and optimization of major machinability parameters (cutting force, surface roughness, and tool wear) in finish dry hard turning (FDHT) for machinability evaluation of hardened AISI grade die steel D₃ with PVD-TiN coated (Al₂O₃-TiCN) mixed ceramic tool insert. The turning trials are performed based on Taguchi's L₁₈ orthogonal array design of experiments for the development of regression model as well as adequate model prediction by considering tool approach angle, nose radius, cutting speed, feed rate, and depth of cut as major machining parameters. The models or correlations are developed by employing multiple regression analysis (MRA). In addition, statistical technique (response surface methodology) followed by computational approaches (genetic algorithm and particle swarm optimization) have been employed for multiple response optimization. Thereafter, the effectiveness of proposed three (RSM, GA, PSO) optimization techniques are evaluated by confirmation test and subsequently the best optimization results have been used for estimation of energy consumption which includes savings of carbon footprint towards green machining and for tool life estimation followed by cost analysis to justify the economic feasibility of PVD-TiN coated Al₂O₃+TiCN mixed ceramic tool in FDHT operation. Finally, estimation of energy savings, economic analysis, and sustainability assessment are performed by employing carbon footprint analysis, Gilbert approach, and Pugh matrix, respectively. Novelty aspects, the present work: (i) contributes to practical industrial application of finish hard turning for the shaft and die makers to select the optimum cutting conditions in a range of hardness of 45-60 HRC, (ii) demonstrates the replacement of expensive, time-consuming conventional cylindrical grinding process and proposes the alternative of costlier CBN tool by utilizing ceramic tool in hard turning processes considering technological, economical and ecological aspects, which are helpful and efficient from industrial point of view, (iii) provides environment friendliness, cleaner production for machining of hardened steels, (iv) helps to improve the desirable machinability characteristics, and (v) serves as a knowledge for the development of a common language for sustainable manufacturing in both research field and industrial practice.

• 대한기계학회논문집
• /
• 제15권6호
• /
• pp.2048-2061
• /
• 1991

본 연구에서는 이와 같은 구비조건과 문제점들을 해소하기 위하여 Fig.1과 같 이 볼 엔드 밀링의 절삭성과 경제적 절삭 속도식을 실용식의 형태로 표현하여 절삭조 건의 최적화를 위한 구속조건으로 설정하였고, 이를 자유곡면의 절삭경로 산출과정에 서 구속조건을 만족하면서 부품당의 생산비를 최소로 하는 스핀들속도와 이송속도를 결정하는 데에 적용하였다. 그리고 이는 실험모형에의 적용예를 통해 계산시간과 정 확도 및 절삭효과 등에 있어서 실용화의 가능성을 검토하였다. 이때 절삭력계를 해 석 함에 있어서는 기하학적 절삭 파라미터들에 대해 무차원적으로 정의된 절삭작용 누 적계수(accumulating coefficient)들을 이용하여 절삭력계를 선형화 된 실용식으로 표 현하였으며, 절삭 상수들과 절삭작용 누적계수들의 선형적 표현에 의해 평균 절삭력계 를 계산한 후, 토크 패턴 모델에 의해 절삭력 집중비를 구함으로써 실 절삭계의 주변 력(peripheral force), 드러스트, 토크, 동력 등을 예측하였다. 또한 절삭속도의 결 정에 있어서는 경제적 절삭속도 예측모델을 설정하여 가공비를 최소로 하는 절삭속도 를 선정토록 하였다.

• 한국정밀공학회지
• /
• 제31권1호
• /
• pp.35-42
• /
• 2014

Recently, in industry field, many researchers are looking for ways to reduce the use of lubricant because of environmental and economical reasons. MQL lubrication is one of many lubrication technologies. The aim of this study is to evaluate the machinability considering lubrication methods and taper angles of workpieces for turning of SCM440. Workpieces of two shapes such as workpiece with and without taper angle are used. And two lubrication methods such as MQL and Wet have been considered. And cutting force and surface roughness are used as characteristic values. Cutting speed, feed rate, injection angle and distance are used as design parameters. The characteristic values were statistically analyzed by Taguchi method. From the results, main effects plot and importance of each parameter according to conditions are analyzed. Finally, this study has been suggested the optimum machining conditions according to the lubrication methods, machining conditions and shape of workpiece.