• 한국음향학회지
• /
• 제32권4호
• /
• pp.301-307
• /
• 2013

수중무기체계에 있어 소나 탐지 성능은 생존성 향상을 위한 중요한 인자이다. 소나의 음향수신 성능을 파악하기 위해서 탄성이론을 이용하여 소나 다층구조의 음향 성능을 해석하였다. 단순구조물에 대하여 탄성이론을 적용하여 얻은 본 해석 결과를 상용해석프로그램인 ANSYS와 비교하였고, 만족할만한 결과를 얻었다. 검증된 탄성이론을 이용하여 소나 다층구조의 층별 두께 변화에 따른 음압 및 반향음 감소 해석을 수행하였다. 무반향(anechoic)층의 두께가 증가할수록 주파수에 따른 음압이 고르게 분포하고 반향음 감소량이 약간 증가하는 것을 확인하였다. 비결합(decoupling)층과 스틸(steel)층의 경우 두께에 따른 음압의 변화는 거의 없으나 두꺼워질수록 반향음이 약간 감소하는 결과를 나타내었다. 탄소강화플라스틱(Carbon Reinforced Platic, CRP)층의 두께 변화는 음압과 반향음 감소량에 영향이 없는 것을 확인하였다. 따라서 소나 다층구조의 음향성능을 높이기 위해서는 무반향층을 두껍게 하고, 비결합층, 스틸층과 탄소강화플라스틱층은 최소화하는 것이 바람직할 것으로 예상된다.

• 한국전기전자재료학회논문지
• /
• 제33권1호
• /
• pp.25-30
• /
• 2020

Oxide (SiO₂)/Metal(Ag)/Oxide(SiO₂, ITO, ZnO) multilayer films were fabricated using a magnetron sputtering technique at room temperature on Si (p-type, 100) and a glass substrate. The electrical and optical properties of the asymmetric multilayer films depended on the thickness of the mid-layer film and the type of oxide in the bottom layer. As the metal layer becomes thicker, the sheet resistance decreases. However, the transmittance decreases when the metal layer exceeds a threshold thickness of approximately 10~12 nm. In addition, the sheet resistance and transmittance change according to the type of oxide in the bottom layer. If the oxide has a large resistivity, the overall sheet resistance increases. In addition, the anti-reflection effect changes according to the refractive index of the oxide material. The optical and electrical properties of multilayer films were investigated using an ultraviolet visible (UV-Vis) spectrophotometer and a 4-point probe, respectively. The optimum structure is SiO₂ (30 nm)/Ag (10 nm)/ZnO (30 nm) multilayer, with the highest FOM value of 7.7×10^-3 Ω^-1.

• 한국방사선학회논문지
• /
• 제3권4호
• /
• pp.23-28
• /
• 2009

단색 엑스선은 적은 방사선 피폭으로 대조도가 높은 의료영상을 만들 수 있다. 엑스선 튜브와 다층박막 거울을 결합하면 높은 플루언스의 단색 엑스선을 얻을 수 있다. 몰리브덴(Mo) 타깃을 갖는 엑스선 튜브에서 Mo 특성방사선(17.5keV)을 높은 반사율로 획득하기 위한 W/C 다층박막 거울의 최적화를 수행하였다. 반사율이 최대가 되는 조건에서 두께주기와 두께비를 결정하였다. 최적 설계된 다층박막 거울에 대한 두께주기와 브래그 정렬에 대한 공차를 구하였다. 증착(deposition) 공차 0.2nm와 회전정렬 공차 ${\pm}0.01^{\circ}$에서 이론 반사율의 85% 이상에 해당하는 반사율이 얻어질 수 있다. 다층박막 거울을 이용하면 높은 플루언스의 특성방사선을 얻어 낼 수 있기 때문에 의료영상 획득 장치에 많이 사용될 것이다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2008년도 추계학술대회 논문집 Vol.21
• /
• pp.259-259
• /
• 2008

The LTCC (Low Temperature Co-fired Ceramic) technology meets the requirements for high quality microelectronic devices and microsystems application due to a very good electrical and mechanical properties, high reliability and stability as well as possibility of making integrated three dimensional microstructures. The wet process, which has been applied to the etching of the metallic thin film on the ceramic substrate, has multi process steps such as lithography and development and uses very toxic chemicals arising the environmental problems. The other side, Plasma technology like ion beam sputtering is clean process including surface cleaning and treatment, sputtering and etching of semiconductor devices, and environmental cleanup. In this study, metallic multilayer pattern was fabricated by the ion beam etching of Ti/Pd/Cu without the lithography. In the experiment, Alumina and LTCC were used as the substrate and Ti/Pd/Cu metallic multilayer was deposited by the DC-magnetron sputtering system. After the formation of Cu/Ni/Au multilayer pattern made by the photolithography and electroplating process, the Ti/Pd/Cu multilayer was dry-etched by using the low energy-high current ion-beam etching process. Because the electroplated Au layer was the masking barrier of the etching of Ti/Pd/Cu multilayer, the additional lithography was not necessary for the etching process. Xenon ion beam which having the high sputtering yield was irradiated and was used with various ion energy and current. The metallic pattern after the etching was optically examined and analyzed. The rate and phenomenon of the etching on each metallic layer were investigated with the diverse process condition such as ion-beam acceleration energy, current density, and etching time.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2014년도 제46회 동계 정기학술대회 초록집
• /
• pp.217.2-217.2
• /
• 2014

We prepared a flexible and transparent CuO/Cu/CuO multilayer electrodes on a polyethylene terephthalate (PET) substrate using a specially designed roll-to-roll sputtering system at room temperature for GFF-type touch screen panels (TSPs). By the continuous roll-to-roll sputtering of the CuO and Cu layer, we fabricated a flexible CuO(150nm)/Cu(150nm)/CuO(150nm) multilayer electrodes with a sheet resistance of $0.289{\Omega}/square$, resistivity of $5.991{\times}10^{-23}{\Omega}-cm$, at the optimized condition without breaking the vacuum. To investigate the feasibility of the CuO/Cu/CuO multilayer as a transparent electrode for GFF-type TSPs, we fabricated simple GFF-type TSPs using the diamond patterned CuO/Cu/CuO electrode on PET substrate as function of mesh line width. Using diamond patterned CuO/Cu/CuO electrode of mesh line $5{\mu}m$ with sheet resistance of 38 Ohm/square, optical transmittance of 90% at 550 nm and an average transmittance of 89% at wavelength range from 380 to 780 nm, we successfully demonstrated GFF-type touch panel screens (TPSs). The successful operation of GFF-type TPSs with CuO/Cu/CuO multilayer electrodes indicates that the CuO/Cu/CuO multilayer is a promising transparent electrode for large-area capacitive-type TPSs due to its low sheet resistance and high transparency.

• 센서학회지
• /
• 제24권1호
• /
• pp.15-21
• /
• 2015

Transparent and conductive multilayer thin films consisting of three alternating layers FZTO/Ag/$WO_3$ have been fabricated by radio-frequency (RF) sputtering for the applications as transparent conducting oxides and the structural and optical properties of the resulting films were carefully studied. The single layer fluorine doped zinc tin oxide (FZTO) and tungsten oxide ($WO_3$) films grown at room temperature are found to have an amorphous structure. Multilayer structured electrode with a few nm Ag layer embedded in FZTO/Ag/$WO_3$ (FAW) was fabricated and showed the optical transmittance of 87.60 % in the visible range (${\lambda}=380{\sim}770nm$), quite low electrical resistivity of ${\sim}10^{-5}{\Omega}cm$ and the corresponding figure of merit ($T^{10}/R_s$) is equivalent to $3.0{\times}10^{-2}{\Omega}^{-1}$. The resultant power conversion efficiency of 2.50% of the multilayer based OPV is lower than that of the reference commercial ITO. Asymmetric D/M/D multilayer is a promising transparent conducting electrode material due to its low resistivity, high transmittance, low temperature deposition and low cost components.

• 한국방사선학회논문지
• /
• 제14권1호
• /
• pp.69-75
• /
• 2020

다층박막 거울은 산업뿐만 아니라 의료 분야에서도 사용되고 있다. 층수가 40인 W/C 다층박막 거울의 성능을 평가하기 위해 엑스선회절분석기로 엑스선반사율을 측정하였다. 40층의 각 층에 대해 두께, 밀도, 계면거칠기를 획득하기 위하여 유전 알고리즘이 사용된다. 기존의 균일 무작위 선택을 하면 해가 수렴하지 않거나 수렴하더라도 오차가 커지는 문제가 발생하여 개선이 요구되었다. 유전 알고리즘의 적합도를 계산하는 시간을 단축하기 위해 C/C++로 병렬 프로그래밍하였다. 제작된 유전 알고리즘은 세대수의 증가와 개체군의 증가에 대해 선형적인 시간 증가를 보여 우수한 scalability를 보였다. 유전 알고리즘의 선택을 균일과 가우시안 무작위를 1:1로 하여 해의 수렴을 보다 안정적으로 개선하였다. 개선된 유전 알고리즘은 다층 박막 거울과 같이 층의 개수가 수십 층 이상이 되는 시료의 각 층의 특성을 파악하는데 적용할 수 있을 것이다.

• Macromolecular Research
• /
• 제16권8호
• /
• pp.725-733
• /
• 2008

Polyimide (PI) multilayer thin films were prepared by spin-coating from a poly(amic acid) (PAA) and poly(amic acid) ammonium salt (PAAS). PI was prepared from pyromellitic dianhydride (PMDA) and 4,4'-oxydianiline (ODA) PAA. Different compositions of PAAS were prepared by incorporating triethylamine (TEA) into PMDA-ODA PAA in dimethylacetamide. PI multilayer thin films were spin-coated from PMDA-ODA PAA and PAAS. The PAAS comprising cationic and anionic moieties were spherical with a particle size of $20{\sim}40\;nm$. Some particles showed layers with ammonium salts, despite poor ordering. Too much salt obstructed the interaction between the polymer chains and caused phase separation. A small amount of salt did not affect the interactions of the interlayer structure but did interrupt the stacking between chains. Thermogravimetric analysis (TGA) showed that the average decomposition temperature of the thin films was $611^{\circ}C$. All the films showed almost single-step, thermal decomposition behavior. The nanostructure of the multilayer thin films was confirmed by X -ray reflectivity (XRR). The LF 43 film, which was prepared with a 4:3 molar ratio of PMDA and ODA, was comprised of uniformly spherical PAAS particles that influenced the nanostructure of the interlayer by increasing the interaction forces. This result was supported by the atomic force microscopy (AFM) data. It was concluded that the relationship between the uniformity of the PAAS particle shapes and the interaction between the layers affected the optical and thermal properties of PI layered films.

• Transactions on Electrical and Electronic Materials
• /
• 제18권4호
• /
• pp.181-184
• /
• 2017

Multilayer ceramics in which piezoelectric layers of $0.90Pb(Zr_{0.48}Ti_{0.52})O_3-0.05Pb(Mn_{1/3}Sb_{2/3})O_3-0.05Pb(Zn_{1/3}Nb_{2/3})O_3$ (0.90PZT-0.05PMS-0.05PZN) stack alternately with silver electrode layers were prepared by an advanced low-temperature co-fired ceramic (LTCC) method. The electrical properties and bonding strength of the multilayers were associated with the interface morphologies between the piezoelectric and silver-electrode layers. Usually, the inner silver electrodes are fabricated by sintering silver paste in multi-layer stacks. To improve the interface bonding strength, piezoelectric powders of 0.90PZT-0.05PMS-0.05PZN with an average particle size of $23{\mu}m$ were added to silver paste to form a gradient interface. SEM observation indicated clear interfaces in multilayer ceramics without powder addition. With the increase of piezoelectric powder addition in the silver paste, gradient interfaces were successfully obtained. The multilayer ceramics with gradient interfaces present greater bonding strength as well as excellent piezoelectric properties for 30~40 wt% of added powder. On the other hand, over addition greatly increased the resistance of the inner silver electrodes, leading to a piezoelectric behavior like that of bulk ceramics in multilayers.

• 대한기계학회논문집A
• /
• 제35권9호
• /
• pp.1007-1013
• /
• 2011

상용차용 다층관 벨로우즈는 우수한 유연성과 내구성이 요구되므로 단층으로 제조되는 승용차용 벨로우즈와는 다르게 다층의 형태로 제작된다. 단층 벨로우즈의 유한요소해석과 최적화에 대한 연구는 활발히 진행되고 있으나, 층과 층사이에 갭이 존재하는 다층형 벨로우즈의 유한요소해석과 최적화 연구는 미진하다. 따라서 본 연구에서는 해석의 신뢰성 향상을 위해 다층형 벨로우즈에 적합한 유한요소 모델을 제시하였으며, 다층관 벨로우즈의 형상 최적화를 위해 실험계획법과 D-Optimal 방법에 기반을 둔 순차적 실험계획에 의한 크리깅 메타모델을 적용하였다.