• Journal of the Korean Wood Science and Technology
• /
• v.47 no.5
• /
• pp.579-586
• /
• 2019

This work examined effects of the synthesis method and melamine content of melamine-urea-formaldehyde (MUF) resins on the bond-line features (i.e. resin penetration and bond-line thickness) in plywood. Two synthesis methods (MUF-A and MUF-B) and three melamine contents (5, 10, and 20%) were employed to prepare MUF resins. The MUF-A resins at three melamine contents were prepared by a simultaneous reaction of melamine, urea, and formaldehyde, while the MFU-B resins were prepared by reacting melamine at the same levels with formaldehyde followed by urea. The results showed that higher melamine content increased the viscosity of MUF-A and MUF-B resins. The resin penetration of MUF-A resins decreased by 48% while those of MUF-B resins increased by 16% at 20% melamine content. As a result, the MUF-A resins had greater bond-line thickness than those of MUF-B resins as the melamine content increased. The MUF-B resins resulted in thinner bond-line and greater resin penetration compared to those of MUF-A resins. The results suggested that MUF-B resins prepared with 20% melamine content had a proper combination of resin penetration and bond-line thickness that could produce plywood panel with a better adhesion performance.

• Journal of the Korean Wood Science and Technology
• /
• v.44 no.6
• /
• pp.913-922
• /
• 2016

This study attempted to measure molecular weight (MW) of melamine-urea-formaldehyde (MUF) resins prepared by two different synthesis methods: the one-step MUF resins were synthesized in one batch procedure, while the two-step MUF resins were prepared by a physical mixing of urea-formaldehyde (UF) resin with melamine-formaldehyde (MF) resin that had been synthesized in a separate procedure. The properties of medium density fiberboard (MDF) panels bonded with two types of MUF resins were also investigated. MWs of these MUF resins were measured using gel permeation chromatography (GPC). In addition, this study measured the MWs of one-step MUF resin during its synthesis procedure. The performance of two types of MUF resins was evaluated by determining properties of MDF panels prepared in laboratory. As the synthesis procedure progressed, both number average MW ($M_n$) and weight average MW ($M_w$) of one-step MUF resin gradually increased, while the polydispersity index (PDI) decreased. And low Mw species of the resin predominantly decreased as the synthesis step progressed. The one-step MUF resin showed greater $M_n$ and $M_w$ than those of the two-step ones even though the PDI values of both resins were very similar each other. As expected, the one-step MUF resin resulted in better properties of MDF panels than those of two-step resins. In particular, the one-step MUF resin provided better internal bond (IB) strength and thickness swelling (TS) with MDF panels than those of two-step ones, indicating better water resistance of the one-step resin. These results suggest that the preparation method of MUF resins have a great impact on the MW and final panel properties.

• Journal of the Korean Wood Science and Technology
• /
• v.48 no.3
• /
• pp.291-302
• /
• 2020

As the properties of the melamine-urea-formaldehyde (MUF) resins were changing during their storage time, this study investigated the impacts of the synthesis method and melamine content of the MUF resins on the pH, apparent viscosity, molecular weights, and crystallinity to estimate these properties over storage times of up to 30 days. Melaminesat three addition levels (5, 10, and 20 wt% based on the resin solids) were simultaneously reacted with urea and formaldehyde (MUF-A resins), while those at the same addition levels were first reacted with formaldehyde and then with urea(MUF-B resins). The pH values of the MUF-A and MUF-B resins decreased linearly as the storage time increased; the apparent viscosity increased linearly for the low melamine contents (5% and 10%) but increased exponentially for 20%. As anticipated, the molecular weights (Mw and Mn) increased linearly with the storage time, with a steeper increase in the Mw of the MUF-B resins compared with that of the MUF-A resins. The crystallinity of the two resin types decreased with storage time at higher melamine content. The relationships between these properties and the storage time made it possible to estimate the property changes in these resins synthesized by the different synthesis methods and melamine contents; this could help predict the properties of such resins in the industry during their storage.

• Journal of the Korean Wood Science and Technology
• /
• v.45 no.4
• /
• pp.409-418
• /
• 2017

This work attempted to manufacture glued-laminated timber (Glulam) bonded with melamine-urea-formaldehyde (MUF) resin adhesives at various melamine contents from 20% to 50% under high frequency (HF) heating for a very short time. Two preparation methods were employed to prepare MUF resin adhesives with different melamine contents: one-batch method of synthesizing MUF resins in a single batch, and two-batch method of mixing urea-formaldehyde (UF) resin with melamine-formaldehyde (MF) resin that had been synthesized separately. As the melamine content increased, the gelation time and peak temperature of MUF resins decreased. The adhesion performance of plywood showed that the one-batch MUF resin adhesive with 50% melamine content only satisfied the standard requirement of water resistance. Thus, the one-batch MUF resin adhesive with 50% melamine content was applied for bonding wood lamina from four softwood species such as Japanese larch, Korean red pine, Korean pine and Japanese cedar to manufacture Glulam under HF heating. All Glulam samples bonded with the one-batch MUF resin adhesives with 50% melamine content except those from Korean Red Pine satisfied the requirement in water soaking or boiling water delamination test as an exterior grade Glulam. The presence of rosin in Korean Red Pine was believed to be responsible for its poor adhesion. These results showed that the one-batch MUF resin adhesives with 50% melamine content provided acceptable water resistance with exterior grade Glulam manufactured under HF heating.

• Journal of the Microelectronics and Packaging Society
• /
• v.29 no.2
• /
• pp.49-52
• /
• 2022

As the difficulty of flip chip products increase, interest in stable PKG material technology from the viewpoint of reliability is increasing. Currently, the representative of poor reliability that are mainly occurring in flip chip PKG are Sn bridge and Cu dendrite. Two type defects are caused by void generated by the flux residue around the bump. In order to essentially minimize the risk of this type of reliability failure, the linkage between the composition of Molded Under-fill (MUF) and flux, which is related material, was reviewed. In this study, the correlation between base resin and filler, which is the main component of MUF, and flux, was defined, and the material composition design was carried out by refer to lesson learn. With the current material composition, it was confirmed that moisture absorption reliability 85%/85%/24hrs pass result and void did not occur during destructive analysis, and developed MUF has shown flux immunity improving result in flip Chip PKG. We think this study can be used in yield enhancement of flip chip process and give insights to study in compatibility between MUF and flux.

• Journal of the Korean Wood Science and Technology
• /
• v.49 no.1
• /
• pp.1-13
• /
• 2021

This study was conducted to investigate the effects of the synthesis method, melamine content, and GPC parameters (such as flow rate, column-detector temperature, and sample injection temperature) on the molecular weight of melamine-urea-formaldehyde (MUF) resins. Two different synthesis methods were employed. In the first method, MUF-A resins were synthesized by simultaneously reacting urea, formaldehyde, and melamine (5%, 10%, and 20%) using the reaction of alkaline-acid-alkaline steps under controlled temperature and viscosity. In the second method, MUF-B resins were synthesized by first reacting melamine at the same levels with formaldehyde and then by adding urea. The highest weight average molecular weight (Mw) of MUF-A resins was found at 10% melamine content when the flow rate was 0.3 and 0.8 ml/min; Mw decreased slightly at 20% melamine content. The results showed that Mw increased with an increase in the melamine content when the flow rate was 0.5 and 1.0 ml/min. In addition, Mw was the highest when the flow rate, column-detector temperature, and injection temperature were 0.3 ml/min, 50℃, and 25℃, respectively. On the contrary, MUF-B resins had greater Mw and number average molecular weight (Mn) than MUF-A resins. Overall, Mw and Mn increased as the melamine content increased. The optimal GPC parameter for MUF resins was determined as follows: a flow rate of 0.5 ml/min, a column-detector temperature of 50℃, and a sample injection temperature of 50℃.

• Journal of the Korean Wood Science and Technology
• /
• v.49 no.3
• /
• pp.274-282
• /
• 2021

Transparent and colorless melamine-urea-formaldehyde (MUF) resins make it difficult to identify the area of wood failure percentage (WFP) in the fracture surface of bonded wood specimens. Therefore, in this study, we develop a method of measuring WFP after the adhesion strength measurement of MUF resins under shear stress. The fractured wood surface of b lock shear strength (BSS) specimens bonded with cold-setting MUF resins at three melamine contents (20%, 30%, and 40%) was marked black, and then, WFP was accurately measured via image analysis. WFP values measured using this method consistently increased with BSS as the melamine content increased, showing the reliability of this new method. The results suggested that this new method is useful and reliable for measuring the WFP of the fracture surface of wood specimens bonded with colorless adhesives such as urea-formaldehyde, MUF, and melamine-formaldehyde resins.

• Journal of the Korean Wood Science and Technology
• /
• v.47 no.2
• /
• pp.200-209
• /
• 2019

To improve the water resistance of melamine-urea-formaldehyde (MUF) resins, different levels of blocked polymeric 4,4 diphenyl methane diisocyanate (B-pMDI) were blended with MUF resins to prepare B-pMDI/MUF hybrid adhesives, and their adhesion performances were evaluated for the surface lamination of fancy veneer on plywood. FT-IR spectra showed that the de-blocked -NCO groups reacted with the -OH of hydroxymethyl groups of the MUF resins to form urethane bonds at 2% B-pMDI/MUF, which was detected before and after their hydrolysis. The mass loss after the hydrolysis consistently decreased as the B-pMDI level increased, indicating an improvement in the water resistance. As the B-pMDI level increased, the activation energy of hybrid adhesives decreased, which improved the reactivity of the hybrid adhesives. Additionally, the water resistance improvement of the hybrid adhesives increased the tensile shear strength of the surface laminated plywood in semi-water proof and water-proof by 23 % and 8 %, respectively, at 2% B-pMDI level. This was likely due to the urethane linkages in the hybrid adhesives. However, the formaldehyde emission from plywood panels bonded with the hybrid adhesives increased in the dry state, indicating incomplete curing of the hybrid adhesives.

• Journal of Chest Surgery
• /
• v.31 no.1
• /
• pp.1-6
• /
• 1998

Total body water is increased after cardiopulmonary bypass resulting in tissue edema and organ dysfunction. Ultrafiltration has been used to reduce this accumulation of water. We have carried out a prospective randomized study in 17 children undergoing open heart surgery, comparing modified ultrafiltration(MUF) with nonfiltered controls. MUF was carried out for about 10 minutes after completion of cardiopulmonary bypass to a hematocrit 36∼42%. Blood loss, blood transfused, hemodynamics, and laboratory data were recorded for 24 hours postoperatively. The results were analyzed using Mann-Whitney U test, comparing controls(n=7) to ultrafiltered(n=10). There was no death in each group. The mean filtrate volume(ml/kg) was 42(30∼68). Blood loss(ml/kg/24hr) was 14.5 mean(4.0∼26.6) in controls versus 12.1 mean(6.0∼21.5) in MUF(P＞0.05) ; blood transfused(ml/kg/24hr) was 9.4 mean (6.0∼36.3) in controls versus 3.4 mean(0∼11.4) in MUF(P<0.05). There was rise in arterial blood pressure during MUF. Percent rise of systolic blood pressure was 4.2(0∼11.7) in controls versus 19.8(7.0∼36.9) in MUF(P=0.001). Percent rise of diastolic blood pressure was 10.0(1.6∼20.8) in controls versus 30.6(5.8∼73.3) in MUF(P<0.05). Platelet count, fibrinogen, and oncotic pressure rose after MUF. No complications directly attributable to the ultrafiltration were observed. Conclusively, MUF is safe, effective means of removing body water and beneficial to hemodynamics.

• Journal of the Korea Furniture Society
• /
• v.15 no.2
• /
• pp.19-27
• /
• 2004

As glulam is a woody material, it is necessary to be more careful in a gluing process. It takes 6-7 hours at $40-60^{\circ}C$ to harden PRF resin used in making structural glulam, and about 24 hours at room temperature. In the present process which can not use a press continuously, reducing the hardening time is necessary to increase production. The experiment was done to compare the adhesive properties of PRF resin and MUF resin through bending test, block shear strength test and water soaking test. In comparing the bending strength of prediction MOE is 1.2 times higher that actual MOE. PRF and MUF do not show significant difference in MOE and MOR, and in block shear strength test, such as shear strength and wood failure rate. However, in water soaking and boiling water soaking tests PRF and MUF show the significant difference in delamination rate.