• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.2 no.1
• /
• pp.5-14
• /
• 2003

Cutting fluids used for superfinishing are usually mineral based oils With sulfur and chlorine additives. These cutting fluids are an environmental hazard and can adversely affect the health of personnel on the shop floor. The present investigation was undertaken to explore the possible alternative use of environmentally-conscious cutting fluids for superfinishing. Unlike mineral oils, these environmentally-conscious cutting fluids are biodegradable and non-hazardous. Experiments were conducted for testing an ester oil manufactured by Accu-Lube applied in miniscule amounts using the Minimum Quantity Lubrication (MQL) technique. A significant improvement in stock removal was found with the 6 stones tested. The specific energy values associated with the process were also significantly lower than those obtained previously with conventional straight oils and the water based synthetic fluid, indicative of better lubrication, while the surface roughness was comparable. These tests prove that MQL with ester oils can be a very effective environmentally-conscious alternative to conventional straight oils.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.13 no.6
• /
• pp.111-118
• /
• 2014

Aluminum lithium alloys are new materials developed for lightweight aircraft parts. However, as compared with conventional aluminum alloys in high-speed machining, problems such as tool wear, machining distortion, and cutting ability arise. This study presents the machining distortion characteristics of an Al-Li alloy wing tip in relation to the cutting heat in high-speed machining. A machining experiment was conducted with high-speed machining equipment for an evaluation of the machining distortion characteristics, with each machining stage temperature change of the workpiece machining surface, and the inside and outside temperature changes of the equipment measured. By measuring the amount of distortion of the workpiece before and after machining, the cutting heat was analyzed with regard to its effect on machining distortion in the product.

• Journal of the Korean Society for Precision Engineering
• /
• v.23 no.6 s.183
• /
• pp.37-43
• /
• 2006

• Journal of the Korean Society for Precision Engineering
• /
• v.19 no.10
• /
• pp.221-226
• /
• 2002

As environmental restriction has continuously become more strict, machining technology has emphasized on development of environment-friendly technologies. In cutting technology, it has been well recognized that cutting fluids might have undesirable effects on workers health and working environment and, hence, recently there have been numerous attempts to minimize harmful effects of cutting fluids on environments. To minimize the use of cutting fluids in machining, conventional cutting fluids have been replaced with the technologies of pressurized cold air and minimum quantity lubrication (MQL). Compared with milling, turning is continuous cutting process, where tools are continuously heated up and lack of lubricity could lead to tool wear and deteriorated surface roughness. In this work, it has been investigated how tool wear and surface roughness could be affected by cutting conditions, supply and cooling methods. The experimental results show that MQL technology is able to minimize conventional cutting fluids.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.2 no.1
• /
• pp.63-68
• /
• 2003

The aspherical lenses are used as objective lens of optical pickup. To examine the design factor the sample product is made before manufacturing of injection mould of lens. The optimum cutting condition of PMMA lens sample with ultra precision SPDT, the roam spindle speed, the depth of cut, the feedrate are found. The demanded surface roughness 100m Ra, aspherical form error $0.5{\mu}m$ P-V for aspherical lens of optical data storage device are satisfied.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2005.06a
• /
• pp.1566-1570
• /
• 2005

The aspherical lenses are used as optical lens of HMD optical system. The optimum cutting condition of PMMA lens sample with ultra precision SPDT, the diamond tool nose radius, the cutting speed, the feed rate, the depth of cut, and cutting fluid type are found. The demanded surface roughness 10 nm Ra, aspherical form error $1.0\;\mu{m}$ P-V for aspherical lens of optical data storage device are satisfied.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.21 no.5
• /
• pp.98-104
• /
• 2022

When processing parts, the cutting oil can improve the cooling performance of the workpiece and tool to increase the precision of the workpiece or extend the life of the tool and facilitate chip extraction. Since such cutting oil has a harmful effect on the environment and the human body due to additives such as sulfur, research on a minimum lubrication supply method using an eco-friendly oil is recently underway. The minimum lubrication supply method minimizes the amount of cutting oil used during processing and processes it, which can reduce the amount of cutting oil used, but has a problem in that cooling performance efficiency is poor. Therefore, this study conducted a study on mist cooling of lubricants to reduce the amount of cutting oil used and maximize the cooling effect of processing heat generated during tapping processing. Spray pressure, processing speed, direction, and lubricant spray amount, which are considered to have an effect on cooling performance, were set as process conditions, and the effect on temperature was analyzed by performing an experiment using the box benquin method among experiments were analyzed. Through the experimental analysis results, the optimal conditions for mist and processing that maximize the cooling effect were derived, and the validity of the results derived through additional experiments was verified. In the case of processing by applying the mist lubrication method verified through this study, it is considered that high-precision processing is possible by improving the cooling effect.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2000.11a
• /
• pp.793-797
• /
• 2000

The environmental problems by using coolant demanded the new cooling methods. As one of them the studies on the dry grinding with compressed cold air have been done. The cooling method using compressed cold air was effdve thmugh going down the temperature of compressed air supplied below $-25^{\circ}C$ and inneasing the amount of mmpresd cold air, but had not enough cooling effect due to the low performance of lubrication. Therefore, the cooling methods using MQL(Minimum Quantity Lubrication) or mist newly were suggested. These two methods can satisfy both cooling effect and lubrication with only small amount of coolant, also has the benefit in the point of decreasing the envimnmental pollution. This paper focused on analyzing the grindmg characteristics of the cooling method using mid. The generated heat and grinding force of the cooling method using mist were compared with them of coolant and compressed cold air. And them grinding test according to the temperature of compressed cold air, mist spray amount and mist supply direction were done.