• 한국공간구조학회논문집
• /
• 제14권3호
• /
• pp.93-100
• /
• 2014

Ethylene Tetrafluoroethylene (ETFE) has been widely used in long-span buildings because of its light weight and high transparency. This paper studies the short and long term creep behaviour of ETFE foil. A series of short-term creep and recovery tests were performed, in which the residual strain was observed. A long-term creep test of the ETFE foil was also performed over 110 days. A viscoelastic-plastic model was then established to describe the short-term creep and recovery behaviour. The model contains a traditional multi-Kelvin part and an added steady-flow component to represent the viscoelastic and viscoplastic behaviour, respectively. The model successfully fit the data for three stresses and six temperatures. Additionally, time-temperature equivalency was adopted to predict the long-term creep behaviour of ETFE foil. Horizontal shifting factors were determined from the process of shifting creep-curves at six temperatures. The long-term creep behaviours at three temperatures were predicted. Finally, the long-term creep test showed that the short-term creep test at identical temperatures insufficiently predicted additional creep behaviour, and the long-term test verified the horizontal shifting factors derived from the time-temperature equivalency.

• 소성∙가공
• /
• 제26권3호
• /
• pp.137-143
• /
• 2017

In this study, a wear test method was proposed to predict the wear life of the CrN layer coated on the surface of the press tools for manufacturing the auto-parts with ultra high strength steel (UHSS) with a tensile strength of 1.5 GPa. The pin-on-disc type wear test was carried out to confirm the feasibility and the reproducibility of the wear amount according to the test conditions such as the normal force, the sliding velocity, and the sliding speed. The test conditions were obtained from the finite element stamping analysis and the wear simulation. With the wear amount from the wear test, a prediction model of the wear depth in the CrN coating layer was proposed according to the test conditions with the design of experiments such as Taguchi method and the response surface method. The derived prediction model was then compared to the result of the Archard wear model, fully describing that the proposed model can effectively predict the wear life of the press tools for the auto-parts with UHSS.

• 자연, 터널 그리고 지하공간
• /
• 제1권2호
• /
• pp.59-71
• /
• 1999

Recently, many deformations in tunnel such as crack and leakage were occulted. Specially, the defects of tunnel lining have been a serious problem in safety and stability many repair works for maintenance in tunnel have been carried out. Therefore, it is necessary to estimate the structural cracking for countermeasure in deformed tunnel and to investigate on the characteristics of lining system and the soundness of tunnel. In this study model tests for tunnel lining were carried out using test apparatus and centrifuge, In the direct loading test, the prototype was Kyungbu high-speed railway tunnel and the scale is 1/10, and lining models were made of concrete. Test conditions included load conditions such as direction, shape and type, lining conditions such as single and double lining, thickness, and reinforcement. In centrifuge model test, the prototype was Seoul subway tunnel and the scale is 1/100, and lining models were made of aluminum and hydrostone. Test conditions included tunnel defects such as thickness shortage. behind cavity and longitudinal cracks, reinforcement methods such as epoxy, grouting and carbon sheet. From these model tests , the characteristics of deformation and failure for tunnel lining were estimated, and the structural behaviors of deformed lining and the effects of repair and reinforcement for tunnel lining were researched.

• The Journal of Asian Finance, Economics and Business
• /
• 제8권1호
• /
• pp.767-780
• /
• 2021

The purpose of this research is to analyze the effect of financial elements (asset growth, liability growth, equity growth, revenue growth, and profit growth) on stock price performance and to analyze the growth of Corporate Social Responsibility (CSR) costs as a moderating effect. The technique analysis used is regression analysis. Samples in this analysis are manufacturing firms listed on the Indonesian Stock Exchange (IDX) for the period 2014-2018. The use of regression models for hypothesis testing must fulfill several applicable assumptions such as Normality Test, Heteroscedasticity Test, Multicollinearity Test, Autocorrelation Test, Model Fit Test, Determination Coefficient Test, and Hypothesis Test. Data analysis used two research models, namely model 1 and model 2. Model 1 is without the moderating variable, and model 2 is with the moderating variable, that is, CSR cost growth. Based on the result of the regression analysis, it can be inferred that the asset, revenue, and profit growth have a positive impact on stock price results. Liabilities and equity growth do not affect stock price performance. Operating expense growth has a significant effect on price performance. CSR cost growth can moderate the effect of growth in financial statement elements on stock price performance but is not significant.

• 드라이브 ㆍ 컨트롤
• /
• 제19권3호
• /
• pp.39-46
• /
• 2022

In South Korea, to evaluate the rollover safety of domestic vehicles, the maximum slope angle of the vehicle is specified, which is verified by the rollover safety test of driving vehicles. However, the domestic rollover safety test is not suitable for buses, because the small amount of static stability factor (SSF) will invalidate the rollover experimental equation due to the high center of mass position of buses. To solve the above problems, a dynamic model of the bus is prepared with assumptions of mass and suspension spring properties. Subsequently, the maximum slope angle of the model was computed by using the simulation of multi-body dynamics, and the result was compared with actual test results to validate the dynamics model. Also, the rollover Fishhook (roll stability) test was conducted in the simulation for driving model. During the simulation, roll angle and roll rate were calculated to check if a rollover occurred. Through the rollover simulation of buses, the domestically regulated formula for rollover safety and the procedure of rollover test for driving vehicles are evaluated. The conclusion is that the present regulation of rollover test should be reconsidered for buses to ensure to get the valid results for rollover safety.

• 터널과지하공간
• /
• 제11권3호
• /
• pp.237-247
• /
• 2001

이 연구에서는 수압파쇄시험 결과의 해석에 대한 파괴역학모델의 적용성을 검토하기 위해 시험결과의 해석에 주로 이용되고 있는 탄성모델과 함게 파괴역학모델을 이론적으로 고찰하였으며, 국내에서 실시된 4개 현장의 측정결과를 이용하여 각 모델의 해석 결과를 비교·검토하였다. 파괴역학모델로부터 얻어진 해석 결과는 탄성모델에 의한 계산 값과 차이를 보였으며, 이러한 차이는 기존 균열의 길이가 작을수록 크게 나타났다. 파괴역학모델은 균열 길이의 판단이 가능한 경우와 같이 특수한 조건에 대해서만 적용이 가능할 것으로 판단된다. 암석의 인장강도는 파괴역학모델에 의한 값이 가장 크게 나타났으며, 압열인장시험, 탄성모델에 의한 값의 순서로 크게 나타났다. 이러한 현상은 시험규모에 따른 크기효과 때문이며, 따라서 수압파쇄시험의 탄성모델로부터 얻어진 암석의 인장강도는 현지암반의 인장강도를 추정할 때 이용될 수 있을 것으로 보인다.

• 대한기계학회논문집A
• /
• 제26권2호
• /
• pp.267-274
• /
• 2002

Using a flexible rotating beam test bed, experimental verification of a flexible multibody dynamic simulations for a rotating beam model has been carried out. The test bed consists of a flexible arm, harmonic driver reducer, AC servo motor and DSP board with PC. The mechanical ports of the test bed has been designed using 3D CAD program. For the simulation model, mass and moment of inertia of each part of the flexible rotating beam test bed are also obtained from 3D CAD model. In the flexible multibody dynamic simulations, the substructuring model has been established to capture nonlinear effects of the flexible rotating beam. Through the experimental verification, substructuring model provides better results than those from the linear model in the high speed rotation.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2007년도 추계학술대회논문집
• /
• pp.1455-1458
• /
• 2007

Vibration characteristics of concrete slabs were investigated using a 1:10 scale model and finite element method. A 1:10 scale model of a test building with 150 and 200mm slab thicknesses was made of acrylic materials. Modal test was conducted to investigate mode shape and modal frequencies. Results show that the mode shapes of two slabs with different thickness are similar each other, whereas natural frequency is different. Through modal analysis using FEM, it was revealed that both mode shapes and natural frequencies calculated from the FEM model are similar to those of the scale model measurement. It was also found that natural frequencies increased with increment of the slab thickness.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2000년도 춘계학술대회 논문집
• /
• pp.703-707
• /
• 2000

Machine tool errors have to be characterized and predicted to improve machine tool accuracy. A real-time error compensation system has been developed based on volumetric error synthesis model which is composed of machine tool errors. This paper deals with new algorithm about verification of machine tool errors. This new algorithm uses a simplified volumetric error synthesis model. This simplified model is constructed with only main components among the error components of the machines. This main error components are analyzed by three-dimensional helical ball bar test. By substituting result of helical ball bar test fer simplified model, we could find that obtained error components are closed to real error components.

• Journal of the Korean Data and Information Science Society
• /
• 제24권6호
• /
• pp.1551-1559
• /
• 2013

In this paper, we analyze the Korean Won/Japanese 100 Yen exchange rate data based on the ARMA-GARCH model, and perform the test for detecting the parameter changes. As a test statistics, we employ the cumulative sum (CUSUM) test for ARMA-GARCH model, which is introduced by Lee and Song (2008). Our empirical analysis indicates that the KRW/JPY exchange rate series experienced several parameter changes during the period from January 2000 to December 2012, which leads to a fitting of AR-IGARCH model to the whole series.