• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.47 no.11
• /
• pp.65-71
• /
• 2010

This paper presents a 14-band LO generator architecture for MB-OFDM UWB systems using 3.1 GHz~10.6 GHz frequency band. The proposed LO generator architecture has been consisted of only one PLL and the fewest nonlinear components to generate 14 LO signals with high purity while consuming low dc power consumption. In addition, major spurious generated from the LO generator have been located in the out of UWB band. The proposed LO generator has been implemented in a $0.13-{\mu}m$ CMOS technology and consumes a dc power consumption of 93~103 mW from a 1.5 V supply. The simulation results show an in-band spurious suppression ratio of more than 41 dBc and a band-switching time of below 3 nsec.

• Journal of ILASS-Korea
• /
• v.12 no.1
• /
• pp.38-44
• /
• 2007

Since the Liquid Phase LPG injection (LPLI) system has Advantages in power generation and emission characteristics compared to the mixer-type fuel-supply system, a variety of studies regarding LPLi system has been conducted and its applications are made in automobile industry. However, the heat extraction due to the evaporation of liquid fuel, causes not only a post-accumulation of fuel but also an icing phenomenon which is a frost of moisture in the air around the nozzle tip. Since there exists a difficulty in the accurate control of air fuel ratio in both fuel supply systems, it can result in poor engine performance and a large amount of harmful emissions. This research examines the characteristics of icing phenomenon and develops anti-icing bushing to prevent an icing on the surface of the injection tip. It was found that n-butane, which has a relatively high boiling point ($-0.5^{\circ}C$), was a main species of post-accumulation. Also the results show that the post-accumulation problem was allevaited the utilization of a large inner to outer bore ratio and smooth surface roughness. In addition, an icing phenomenon and its formation process were found to be mainly affected by the humidity and the temperature of inlet air in an inlet duct. Also, it was observed that an icing phenomenon is lessened using aluminum bushing whose end coincides with the end of fuel injection tip in length.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2010.03a
• /
• pp.1452-1457
• /
• 2010

Recently, coal ash is used as resources to make controlled low-strength material (CLSM) which a self-compacted, cementitious material used primarily as a backfill in lieu of compacted fill. Pozzolanic reaction is strongly related with self-cementation of coal ashes. However, this reaction depends on pozzolanic content in fill materials and is disappeared in 2-3 days after placement of coal ash fill. Therefore, state of coal ash fill is commonly very loose and not appropriate for foundations of structures without special treatments. In this study, a coal ash placement device was developed to place coal ashes effectively to improve density of coal ash fills. The device consists of a ribbon type mixer to obtain homogeneous materials mixture and a piston type pump for density control of fill materials. Based on several laboratory test results, more stable coal ash fill state can be obtained with controlling placement pressure.

• Journal of Environmental Science International
• /
• v.21 no.12
• /
• pp.1523-1528
• /
• 2012

This study was carried out to develop pilot plant Net3FM(Net Fit Fiber Filter Module) system and to suggest optimum operating condition for municipal wastewater reuse. SS concentration of biologically treated sewage effluent was reduced from 1.5~5.4mg/L to 0.4~1.0mg/L without coagulant injection in Net3FM system, and the SS removal efficiency was average 84.7%. And also, the removal efficiencies of COD and T-P were decreased slightly due to the SS removal by filtration. Coagulation-Filtration test was conducted to enhance the removal efficiencies of SS and T-P. The optimum dosage of coagulant was injected automatically by auto-controlling system, which is controlled by detecting value of turbidity of secondary sewage effluent. SS, COD and T-P concentrations in filtrated effluent were 0.21~0.57, 1.6~6.2 and 0.137~0.392mg/L with coagulant injection by in-line mixer in Net3FM system, respectively. The removal efficiencies of SS and T-P were highly increased to 92.8% and 89.8%, respectively. It was due to the combined the processes of coagulation and filtration. Net3FM system was evaluated that the removal efficiency of pollutants in secondary sewage effluent and the utilization potential as reclaimed water technology were very high.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.25 no.3
• /
• pp.282-288
• /
• 2014

In this paper, we have analyzed and designed a digital RF receiver based on the optimization of the dynamic range parameter to secure the wideband characteristics and linearity of digital radar receivers. To improve the wideband characteristics and dynamic range, a low noise amplifier is matching design with a noise source to minimize the noise figure in 1 GHz bandwidth and we improved the linearity of RF-receiver by securing the conversion gain characteristics of receiver through the design of active mixer. RF receiver is designed to give gain 63 dB, noise figure 1.2 dB and dynamic range of RF receiver has 75.8 dB in a wide band of 8.8~9.8 GHz. It is shown to be applicable to X-band digital radar receiver.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.49 no.12
• /
• pp.242-246
• /
• 2012

This paper presents an integrated low noise and highly linear wideband RF front-end for a digital terrestrial and cable TV tuner, which are used as a part of double-conversion TV tuner. The low noise amplifier (LNA) has a low noise figure and high linearity by adopting a noise canceling technique based on current amplification. The up-conversion mixer and SAW buffer have high linearity by employing a third order intermodulation cancellation technique. The proposed RF front-end is designed in a $0.18{\mu}m$ CMOS and draws 60 mA from a 1.8 V supply voltage. The RF front-end shows a voltage gain of 30 dB, an average single side-band noise figure of 4.2 dB, an IIP2 of 40 dBm, and an IIP3 of -4.5 dBm for the entire band from 48 MHz to 862Hz.

• The Journal of Korean Academy of Prosthodontics
• /
• v.39 no.6
• /
• pp.589-598
• /
• 2001

The fracture of acrylic resin dentures remains an unsolved problem. Therefore, many investigations have been performed and various approaches to strengthening acrylic resin, for example, the reinforcement of heat-cured PMMA resin using glass fibers, have been suggested over the years. The aim of the present study was to investigate the effect of short glass fibers treated with silane coupling agent on the transverse strength of heat-polymerized PMMA denture base resin. To avoid fiber bunching and achieve even fiber distribution, glass fiber bundles were mixed with PMMA powder in conventional mixer whose blade was modified to be blunt. Composite of glass fiber($11{\mu}m$ diameter, 3mm & 6mm length, silane treated) and PMMA resin was made. Transverse strength and Young's modulus were estimated. Glass fibers were incorporated with 1%, 3%, 6% and 9% by weight. Plasticity and workability of dough was evaluated. Fracture surface of specimens was investigated by SEM. The results of this study were as follows 1. 6% and 9% incorporation of 3mm glass fibers in the PMMA resin enhanced the transverse strength of the test specimens(p<0.05). 2. 6% incorporation of 6mm glass fibers in the PMMA resin increased transverse strength, but 9% incorporation of it decreased transverse strength(p<0.05). 3. When more than 3% of 3mm glass fibers and more than 6% of 6mm glass fibers were incorporated, Young's modulus increased significantly(p<0.05). 4. Workability decreased gradually as the percentage of the fibers increased. 5. Workability decreased gradually as the length of the fibers increased. 6. In SEM and LM, there was no bunching of fibers and no shortening of fibers.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.16 no.2 s.93
• /
• pp.189-193
• /
• 2005

In this paper, we propose a direct conversion double-balanced down-converter fer MB-OFDM W system, which is implemented using $0.18\;{\mu}m$ CMOS technology and its measurement results are shown. The proposed down-converter adopts a resistive current-source instead of general transconductance stage using MOS transistor to achieve wideband characteristics over RF input frequency band $3\~5\;GHz$ with good gain flatness. The measured conversion gain is more than +3 dB, and gain flatness is less than 3 dB for three UWB channels. The dc consumption of this work is only 0.89 mA from 1.8 V power supply, leading to the low-power W application.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.15 no.12 s.91
• /
• pp.1184-1189
• /
• 2004

A new schematic of quadrature voltage controlled oscillator(QVCO) is designed and fabricated. To obtain quadrature characteristic and low phase noise simultaneously, two differential VCOs are forced to un in quadrature mode by using coupling amplifier with a source degeneration resistor, which is optimized to obtain quadrature accuracy with minimum phase noise degradation. The designed QVCO was fabricated in standard CMOS technology. The measured performance showed the phase noise of below -120 dBc/Hz at 1 MHEz frequency offset, tuning bandwidth of 210 MHz from 2.34 GHz to 2.55 GHz with a tuning voltage varying form 0 to 1.8 V Quadrature error of 0.5 degree and amplitude error of 0.2 dB was measured with conjunction with low-lF mixer. The fabricated QVCO requires 19 mA including 5 mA in the VCO core part fiom a 1.8 V supply.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.15 no.5
• /
• pp.480-485
• /
• 2004

In this paper, a new predistortion linearizing method using frequency up-conversion operation of mixer is proposed. This linearizing method doesn't require any additional signal sources in spite of frequency up-conversion mixing operation. This method extracts the 2nd low frequency intermodulation distortion signal from input signals and uses the extracted 2nd low frequency intermodulation distortion signal as mixing signal source. To show validation of the proposed predistortion method, we made K-PCS power amplifier. On 2-tone signals amplification process, the (C/I) ratio of amplifier is improved 26 ㏈ (@Po=22 ㏈m/tone), where two tones are 1.8544 ㎓ and 1.8556 ㎓, respectively. And (C/I) ratio is improved more than to 20 ㏈ for 17 ㏈ output signal dynamic range. On IS-95A CDMA 1FA amplification process, the improvements of adjacent channel power ratio(ACPR) are 10.8 ㏈ and 6.4 ㏈ at ${\pm}$885 ㎑ and ${\pm}$1.25 ㎒ offset points, respectively.