• 동력기계공학회지
• /
• 제1권1호
• /
• pp.70-79
• /
• 1997

Ni-base self-fluxing alloy powder particles were flame sprayed onto the SS400 mild steel substrate surface. The effects of both substrate temperature and spraying distance on the splat behavior of sprayed particles were examined. The results obtained are summarized as follows: 1) In the splat behavior of Ni-base self-fulxing alloy particles sprayed onto the SS400 mild steel substrate, splashing was observed under the room temperature condition. On the contrary, it showed circular plate pattern in the substrate temperature range over 373K. 2) It was cleared that there was close relationship between mechanical properties of coating layer and splat behavior of sprayed particles. 3) From the experimental results, optimum spraying conditions showed excellent mechanical properties in the case of Ni-base self fluxing alloy sprayed onto the SS400 mild substrate were 473K of substrate temperature and 250mm of spraying distance.

• 한국연소학회지
• /
• 제21권4호
• /
• pp.39-47
• /
• 2016

The aims of this research were to investigate combustion characteristics of lab-scale pressurized oxy-fuel combustion(POFC) system. In this study, the reactor, 800 mm long, was equipped with co-axial burner. Low calorific value syngas that is composed of mainly CO and $H_2$ was used as fuel whereas pure oxygen was used as an oxidant. Thermal heat input to the reactor varied from 2.6 kW to 6.1 kW. The reactor pressure also increases from atmospheric up to 15 bar. The results show that as the pressure increase, the temperature of reactor decreases on the whole in all cases. A significant temperature drop was observed especially at the bottom section of the reactor that exist flame. In addition, the flame instability increases as the pressure increases. Furthermore $NO_x$ emissions increases from atmospheric up to 2 bar. However beyond 2 bar, $NO_x$ emission reduces as pressure increases. Lastly $NO_2$ ratio in $NO_x$ also increases as pressure increases.

• Journal of Advanced Marine Engineering and Technology
• /
• 제24권1호
• /
• pp.49-58
• /
• 2000

Thermal spraying is one of the most common surface coating techniques to be used for many applications and flame spraying covers a wide range of different materials which can be coated onto various substrates. The purpose of this study is to investigate the effects of mixed ratio in composite coatings on the mechanical and anti-corrosion properties. The five different types of composite coatings were made with $Al_2O_3$ ceramic and Ni-alloy powder on the mild steel substrate by flame spraying method. The mechanical properties such as microhardness, adhesive strength and erosion resistance and corrosion resistance were tested for the sprayed coating specimens. The results obtained are summarized as follows; 1. The composite coating layers greatly improve the microstructure, erosion resistance and adhesive strength by increasing the content of Ni-Al alloy. 2. Microhardness of the compsite coating layer is decreased by increasing the content of Ni-Al alloy. 3. The anti-corrosion properties is considerably improved by increasing the compsite rate of Ni-Al alloy.

• 대한수의학회지
• /
• 제51권1호
• /
• pp.69-72
• /
• 2011

Eosinophilic granuloma is a common hypersensitive inflammatory skin disease in cats, and rare in dogs and horses. The skin biopsies of 5 years old female Cocker spaniel and 2 years old female mixed dog had the clinical signs of skin nodules with alopecia were submitted for diagnosis. Solitary skin nodules and papillary nodules were presented on the left external ear and back of Cocker spaniel and on the external ear of mixed dog, respectively. Histopathologically, epidermis of skin showed mild to severe hyperplasia with multifocal ulceration. Small to large irregular, brightly eosinophilic foci with degenerating eosinophils and homogeneous degenerated collagens were existed in the dermis of both ear and back skin. Typical 'flame figures', a mixture of degenerated collagen and degranulated eosinophils, were observed in both cases. Based on the histopathologic findings and special staining characters, 2 cases were diagnosed as canine eosinophilic granuloma. This is the first report for the eosinophilic granuloma of dogs in Korea.

• 한국안전학회지
• /
• 제26권5호
• /
• pp.1-6
• /
• 2011

Flame extinction and the chemistry of stoichiometric methane/air mixture were investigated numerically in the PSR(perfectly stirred reactor). For the study, PSR code was modified to be possible to unsteady calculation, and the sinusoidal fluctuation was subjected to the residence time. In the region of residence time far from the extinction limit, combustion mode was strongly dependent on the frequency. The low frequency excitation provided the quasi-steady behavior on the temperature and the concentrations of related species, but small variation of temperature was observed under high frequency. In the region of residence time near the extinction limit, the mixture subjected above 1 KHz was still reacting even though extinction had to be occurred under quasi-steady concept. The attenuation of extinction limit resulted from that chemical time was comparable to the flow time. The mean mole fractions of both NO and CO were almost same regardless of imposed frequency. However, the average mole fraction of $C_2H_2$ was decreased as increasing frequency, which implies that soot yield might be reduced at the higher frequency of flow excitation. The result provides the basic concept for flame stabilization, and it will be used to design a mild combustor.

• 대한기계학회논문집B
• /
• 제36권1호
• /
• pp.75-81
• /
• 2012

고온의 동축류 공기와 수소가 함유된 메탄 연료제트에서 자발화된 층류 부상화염의 특성을 실험적으로 조사하였다. 그 결과로 순수 메탄 제트에서 자발화되는 경계 온도인 920 K 를 초과하는 초기 온도에서 메탄/수소 혼합기의 자발화된 부상화염은 연료 몰분율에 따라 삼지화염 또는 마일드 연소를 보였고, 제트속도에 따라 부상화염의 높이가 증가하는 전형적인 특성을 보였다. 소량의 수소가 첨가된 부상화염의 높이는 메탄의 경우와 유사하게 단열적 점화지연시간의 2 승에 대한 의존성이 유지되었다. 반면에, 초기 온도가 920 K 미만인 경우에서 화염은 수소의 점화 촉진에 의해서 자발화 되었다. 그리고 제트속도가 증가함에 따라 자발화된 부상화염의 높이는 비선형적으로 감소하는 독특한 특성을 보였으며, 수소의 선호확산이 그 현상에 대해서 중요한 역할을 할 것으로 예상된다.

• Journal of Advanced Marine Engineering and Technology
• /
• 제15권3호
• /
• pp.39-44
• /
• 1991

The purpose of this investigation is to examine the effects of spraying conditions on the mechanical properties of flame-sprayed titania ceramic coating layer. Titania ceramic was sprayed onto the mild steel substrate under the various spraying conditions. Spraying distances were 100, 150, 200, 250mm respectively and pinch air pressures were 0.2 0.3, 0.4 MPa at each spraying distance. The mechanical properties such as microhardness, adhesive strength and erosion wear resistance were tested for the specimens sprayed under the various spraying conditions above mentioned. The optimum operational conditions obtained through the experimental results were 150mm of spraying distance and 0.3 MPa of pinch air pressure.

• Journal of Welding and Joining
• /
• 제32권1호
• /
• pp.47-52
• /
• 2014

Due to of high intensity, lower noise and easy controllability of the heat, induction heating system became well known. Induction heating method has been suggested as substitute for the gas heat source and adopted in the automation of curved hull forming system. In this study, an investigation was accomplished to find the effects on the change of material properties when the induction heating was applied on the mild steel plate. Plates were heated using weaving method to get sufficiently heat affected zone and then cooled with water or in the air. The mechanical properties of the heated plate were evaluated. As results, the tensile test, impact test and microstructures satisfied the class rule.

• 한국분말재료학회지
• /
• 제12권2호
• /
• pp.136-145
• /
• 2005

Graphite-Ni composite powders were synthesized by mechanical alloying(MA) and spray drying(SD). Fabricated powders as well as commercial graphite-Ni powders were thermally sprayed on mild steel substrates using high velocity oxygen fuel (HVOF) thermal spray process and flame thermal spray process. The effects of several process parameters on related properties in thermally sprayed coatings have been investigated and correlated with microstructures in this study. The results indicated that the desired properties can be obtained when commercial powders were applied using HVOF process, while coating properties in case of MA powder application were inferior to those in HVOF process in so far. However, it is suggested that property enhancement can be obtained if the fraction of hexagonal graphite phase can be increased in mechanically alloyed powders.