• 한국표면공학회지
• /
• 제42권1호
• /
• pp.34-40
• /
• 2009

In the study, it was carried out dissimilar metal welding on materials for Al ship. The electrochemical and mechanical characteristics evaluated for specimen welded by ROBOT. The hardness of welding zone is lower than those of heat affected zone and base metal. At the result of tensile test, the specimen welded with ER5183 welding material presented excellent property compared with ER5556. The polarization trend for the base metal and welding metal showed the effects of concentration polarization due to oxygen reduction and activation polarization due to hydrogen generation. At the Tafel experiments result, the corrosion density in welded with ER5183 welding material presented the lowest value.

• Journal of Welding and Joining
• /
• 제33권1호
• /
• pp.61-71
• /
• 2015

The effect of welding condition on microstructure and mechanical property of Plasma-MIG Hybrid Weld between Al 5083 plates(thickness : 10mm) was investigated. 1 pass weld without any defects such as puckering, undercut, and lack of fusion was obtained by 150~200A of plasma current and 5~7mm of welding speed. Gas porosities and shrinkage porosities were existed in the weld near fusion line. As welding speed and plasma current were decreasing, the area fraction of porosity was increasing. The hardness of the weld is increasing as welding speed. On the basis of microstructural analysis, Mg segregated region near dendrite boundaries tends to increase with the welding speed. In the result of hardness test, Distribution of hardness in fusion zone showed little change with the plasma current. However, when the welding speed increased, hardness in weld metal markdly increased. It could be considered that effect of heat input to growth of the dendritic solidification structures. Based on tensile test, tensile properties of weld metal was predominated by area fraction of porosities. Consequently, tensile properties can be controlled by formation site and area fraction of porosity.

• Journal of Welding and Joining
• /
• 제32권1호
• /
• pp.28-33
• /
• 2014

In this paper, I-butt welding with 6mm thickness using Plasma-GMA welding was carried out. And weld characteristics of the Al-5083 aluminium alloy for Plasma-GMA hybrid welding was evaluated. The orthogonal experimental design was used to investigate the influence of plasma-MIG welding parameters such as plasma current, wire feeding rate, MIG-welding voltage and welding speed on the weld bead geometry and tensile strength using the ANOVA(Analysis of Variation). Then we conducted evaluation of contribution for process parameters. ANOVA results show that bead dimensions are affected by wire feeding speed, welding voltage and welding speed and tensile strength is mainly affected by welding speed and plasma arc current. Tensile strength was decreased by rise in plasma welding current because GMA welding current was decreased by plasma arc.

• 한국산학기술학회논문지
• /
• 제18권11호
• /
• pp.124-129
• /
• 2017

본 연구에서는 철도차량의 경량 차체 소재로 주로 사용되는 알루미늄 합금 (Al-6005-T6) 압출재에 대한 마찰교반접합 적용 연구를 수행하였다. 용접속도를 300 mm/min으로 고정시킨 채 회전 공구의 회전속도를 600, 900, 1200, 1600 rpm으로 변화시킬 때 미세구조 및 기계적 특성의 변화에 대해 평가하였다. 특히, 동일 소재에 대해 전통적인 용접방법인 MIG 용접된 시편과의 비교를 통해 마찰교반접합법의 철도차량 적용성에 대해 논하였다. MIG 용접방법과는 달리, 마찰교반접합부에는 미세기공이 발견되지 않았으며, 경도 측정 결과 공구의 회전속도가 빨라질수록 높아진 입열량에 따라 heat affected zone (HAZ)의 범위가 넓어지고 결정립 조대화에 따라 HAZ의 경도 또한 낮아지는 것을 확인하였다. 인장시험 결과 HAZ지역에서 파단이 발생하였으며, 본 연구에서 설정한 공구의 회전속도 범위에서는 nugget 부의 경도 변화는 발견되지 않았으나 rpm이 올라갈수록 인장강도와 항복강도가 떨어지는 경향을 보였으며 이는 경도 시험에서와 같이 HAZ지역의 결정립 크기의 증가로 인한 현상으로 판단된다.

• Journal of Welding and Joining
• /
• 제26권6호
• /
• pp.4-7
• /
• 2008

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2009년 추계학술발표대회
• /
• pp.31-31
• /
• 2009

최근 전세계적으로 유가상승 및 환경에 대한 관심이 증대되면서 자동차 업계에서는 차량 경량화를 통한 연비향상에 대한 연구가 활발히 진행되고 있다. 대표적인 기술개발 사례로서 초경량 철강 차체의 개발을 들 수 있다. 이는 고장력강을 적용함으로써 강성을 증대시킴과 동시에 두께감소에 의한 경량화를 이루고자 추진되고 있다. 하지만 고장력강은 자체의 높은 강성을 지니고 있는 반면, 일반 강종에 비해서 스프링백이 크고 용접성도 많이 떨어지는 제약을 안고 있다. 아크 용접법 중 하나인 AC pulse MIG 용접은 DCEP (direct current electrode positive) 와 DCEN (direct current electrode positive) 구간이 주기적으로 반복하는 용접법으로 스패터 발생이 거의 없으며 특히 갭 접합성이 우수하여 자동차 차체 조립공정에 적용되고 있다. 본 연구에서는 자동차 차체용 AHSS 소재의 겹치기 용접 실험을 통해 실제 생산라인에서 용접 이음부에 발생되는 갭에 대해 강건한 용접 공정 조건을 제시하였다. 먼저 고속카메라 촬영을 통해 AC pulse MIG 용접에서 EN ratio 변화에 따른 와이어 용융현상을 분석 하였으며 단면마크로, 인장시험, 인장 파단면 분석을 통해 겹치기 용접에서 0~2mm 사이의 갭 발생에 강건한 용접 조선을 제시하였다.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2008년도 춘계학술발표대회 개요집
• /
• pp.30-30
• /
• 2008

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2005년도 춘계학술발표대회 개요집
• /
• pp.331-333
• /
• 2005

It comes up conversation in automobile industry that some technologies related to production and quality for goods have to be developed to make rationalization of the unit cost of production because material of car muffler is replaced by expensive stainless steel having corrosion-resistance and oxidation-resistance. Quality evaluation and control is direct method for the company producing welded goods in large quantities to increase productivity and to improve quality. It seems that prevention of inferior quality and increasement of productivity will be hard if production design does not have quality evaluation method related to weld assembly, They have been producing welded goods using MIG weld but still do not have not only quality evaluation method but also evaluation criterion for welded joint. In this study, the way for development of quality evaluation method is showed by analysis and calculation of waveform to improve technology related to welding process

• Journal of Advanced Marine Engineering and Technology
• /
• 제38권10호
• /
• pp.1190-1199
• /
• 2014

As a considerable, experimental approach, an autocarriage type of $CO_2$ welding machine and a MIG(metal inert gas) welding robot in the inert gas atmosphere were utilized in order to realize Al 5083 welding to hull and relevant components of green leisure ships. This study aims at investigating the effect of welding conditions(current, voltage, welding speed, etc.) on thermal deformation that occurs as welding operation and tensile characteristics after welding, by using Al 5083, nonferrous material, applied to manufacturing of eco-environmental leisure ships. With respect to welding condition to minimize the thermal deformation, 150 A and 16 V at the wire-feed rate of 6 mm/sec were acquired in the process of welding Al 5083 through an auto carriage type of $CO_2$ welding feeder. As to tensile characteristics of Al 5083 welding through a MIG welding robot, most of tensile specimens showed the fracture behavior on HAZ(heat affected zone) located at the area joined with weld metal, except for some cases. Especially, for the case of the Al specimen with 5 mm thickness, 284.62 MPa of tensile strength and 11.41 % of elongation were obtained as an actual allowable tensile stress-strain value. Mostly, after acquiring the optimum welding condition, the relevant welding data and technical requirements might be provided for actual welding operation site and welding procedure specification (WPS).

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2002년도 Proceedings of the International Welding/Joining Conference-Korea
• /
• pp.255-259
• /
• 2002

VIRGO 104 is a low carbon martensitic stainless steel that is applied to the famous Three Gorges Project. By using VOD melting process VIRGO 104 has low carbon and [H] [O] contents, and shows excellent mechanical properties and weldability. The best solution to guarantee welding quality is PWHT by 600 Cx8h.