• Journal of Welding and Joining
• /
• 제23권1호
• /
• pp.69-76
• /
• 2005

Recently, application of arc welding to galvanized carbon steel sheet is on the increasing Ould in the fields of automobile and construction industries. In arc welding process, zinc is evaporated in weld pool, even under the appropriate welding condition and produce blowhole and/or pit. Zinc gas cause instability of arc and increase spatter and fume. This research is purposed to minimize the heat-input and the formation of porosities in the welded joint of the galvanized carbon steel sheet using variable polarity AC wave pulse MIG welding system. An appropriate welding condition which showed low spatter and good bead appearance was acquired by applying the AC pulse MIG welding machine to DC duplicated MIG welding with the solid wire. When oxygen gas was added to shield gas of MIG welding for galvanized steel sheet, arc length was increased and arc stability was improved. In the AC duplicated welding, the loss of galvanized layer was decreased as the amount of heat-input was decreased when the EN ratio was increased under the condition that average welding current was evenly set.

• 조명전기설비학회논문지
• /
• 제22권10호
• /
• pp.141-149
• /
• 2008

최근 에너지 절감과 환경개선 문제가 대두되면서 아크용접에서도 깨끗하고 불량률이 낮은 아크용접기기의 개발을 본격적으로 추진하고 있다. 본 연구에서는 알루미늄 등과 같은 비철금속에 주로 적용되는 MIG 아크용접에서의 용접성능을 개선하고자 한다. 기존의 직류펄스 MIG 아크용접은 박판 금속에 용접을 하는 경우 아크전압이 낮아 단락이 빈번하게 발생하고 용접 불량을 일으킨다. 이를 개선하기 위하여 중첩교류 펄스를 적용한 MIG 아크용접방법을 제안하고 중첩교류펄스의 설계와 실험을 통하여 그 타당성을 검증하였다.

• Journal of Welding and Joining
• /
• 제21권4호
• /
• pp.56-62
• /
• 2003

MIG brazing is used for many parts without melting base metal because of high productivity. Pulsed MIG brazing can be used to further reduce heat input and to improve the process stability. However, a significant amount of zinc in galvanized sheet steel is burned off in the area of brazes. Therefore, the brazing method to reduce the heat input is needed. In the brazing for galvanized sheet steel, variable polarity AC pulse MIG arc brazing can be applied to more decrease the heat input by setting EN-ratio adequately. In this research, we studied for the variable polarity AC pulse MIG arc brazing to decrease the heat input by using ERCuSi-A wire. As the result of increasing EN-ratio, melting ratio of base metal and burning off of zinc were reduced in galvanized sheet steel.

• Journal of Electrical Engineering and Technology
• /
• 제2권3호
• /
• pp.366-372
• /
• 2007

Joining thin aluminum alloy is difficult using most welding techniques. Many of the problems are associated with bum-through by the high heat input. Common welding techniques are TIG (Tungsten Inert Gas), MIG (Metal Inert Gas), and PULSE-MIG welding. The method provides more control of the heat balance in the welding arc by taking advantage of the different arc characteristics obtained with each of the two polarities. In this paper, we proposed a new welding method by control DSP 320C32, and the characteristic and experiment result-voltage, current, welding bead, and penetrations by this method are presented.

• Journal of Welding and Joining
• /
• 제28권6호
• /
• pp.28-34
• /
• 2010

This paper was described on investigation to prevent porosity in high speed MIG Welding of Al 6082-T6. Porosity measurement was carried out by using image analysis of micrographs with the help of an analysis software. The main parameter was arc length and torch progressive angle. The porosity ratio was increased as arc length was increased. The arc length was increased depending upon the output voltage. By proper selection of pulse waveform parameter, the stable arc of one pulse one drop was generated. The porosity ratio of optimum condition in one pulse one drop was lower than high voltage condition. When torch progressive angle was an angle of advance $10^{\circ}$, porosity ratio was minium.

• Journal of Welding and Joining
• /
• 제29권4호
• /
• pp.27-29
• /
• 2011

• Steel and Composite Structures
• /
• 제11권3호
• /
• pp.225-232
• /
• 2011

In this study, the deflection and deformation behaviours of IPN80 steel beam and column were investigated under the different industrial loads. Single-sided welds were applied to IPN80 steel beams using shielded metal arc (SMAW) and metal inert gas welding (MIG) method in the form of T-type. After that, the performance of SMAW and MIG welded joints were identified using beam bending test under 500 and 3000 N loads. SMAW and MIG methods were compared with each other to understand the deflection and deformation behaviours of the welded steel structures. Lower deformation and deflection were obtained in MIG welded steel beams. The results show that, steel beams welded MIG method has higher load capacity than SMAW welded ones. MIG welding method is more reliable than the SMAW method for the combining performance and load capacity.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2003년도 춘계학술발표대회 개요집
• /
• pp.81-83
• /
• 2003

The potential advantages of the hybrid welding process are improved weld penetration, enhanced gap tolerance, control of weld metal composition, and improved weld quality in comparison to laser or arc welding. Especially, the deep penetration of hybrid welding is very attractive in welding of thick plates. In this study, therefore, the influence of arc power in hybrid welding on detailed bead dimensions at different laser power levels was investigated.

• 전력전자학회논문지
• /
• 제8권4호
• /
• pp.307-312
• /
• 2003

가볍고 강도가 높은 이유로 부품의 경량화가 요구되는 분야에 급속하게 이용되고 있는 알루미늄의 아크용접에 관한 연구로써, 기존 알루미늄의 아크용접 방법-TIG, MIG-에 비하여 속도가 빠르고, 보다 얇은 박판에 용접이 가능한 용접 방식에 대한 연구 결과이다. 용접전류를 펄스 형태의 인가하여 줌으로써 1펄스 1용적이행이 가능하였고, 용접전류의 극성을 주기적으로 교번하여 용적의 입열량 차이를 이용하여 용입의 깊이를 제어하는 알고리즘을 적용하였고 그 상관관계를 증명하였다. 본 연구에서는 DSP 320C32를 이용한 풀 디지탈 제어방식의 10kw 펄스MIG용 접전원장치를 제작하였고, 120cm/분의 용접속도로 1.2mm의 알루미늄 박판에 극성비 0∼40%의 변화한 용접 결과에 대하여 용접외관 및 단면에 대한 결과를 검토하였다.

• Journal of Advanced Marine Engineering and Technology
• /
• 제32권2호
• /
• pp.306-314
• /
• 2008

General metal welding occurs distortion. Also, reducing distortion is required much cost. Therefore, the purpose of this study is optimization of welding conditions to reduce distortion in welding of monolithic rack housing for modular steering gear. Firstly, heat source for welding was chosen arc and laser. Secondly, it investigated optimizing welding conditions in bead welding by arc and laser heat source, and welding conditions in fillet welding was optimized with welding shapes. Finally, it was measured temperature distribution of welds by infrared camera and angle distortion in fillet welding. As a result, laser welding was superior to arc welding on distortion.