• Journal of the Korea Furniture Society
• /
• v.10 no.2
• /
• pp.29-36
• /
• 1999

During a radio-frequency/vacuum plus press drying process of some hardwood veneers for decoration we investigated the effect of a grain and thickness of a veneer sheet on drying rates, variations of final moisture content within a bundle of veneer sheets, and formation of checking, end waving, and burning mark. About thirty three hundreds sheet of veneer could be dried in sixty five hours from green to in0-use moisture content, and a final moisture content was significantly effected by initial moisture content of veneer. There were nearly variations in a final moisture content among the veneer sheets in the same bundle. A checking was never found in a edge-sliced veneer, and very slight in a flat-sliced veneer of ash and red oak. There were no end waving and no burning mark in all veneer sheets.

• Proceedings of the KSME Conference
• /
• 2000.04a
• /
• pp.737-740
• /
• 2000

Injection molded plastic parts have many appearance imperfections: weld line sink mark flow mark, gloss, shading, scratching, etc. Because these appearance faults have not accepted esthetically, so pastic parts are produced through painting or texturing. The purpose of this paper is to develop a paintless molded part of TV Mask Front, using numerical simulations and experiments. In order to minimize problems of injection, this study carried out computer aided injection mold filling simulations using MF/FLOW. Based on these numerical results we developed FR(Flame Retardant) HIPS and estabilished guidelines of part design, mold design, and processing conditions. We took effects of cost savings, inprovement of productivity, and utilization of recycling by eliminated painting process.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2001.05a
• /
• pp.692-695
• /
• 2001

The EMFG(Extended Mark Flow Graph) is not only a powerful tool to. designing the discrete-event system conceptually or specifically but also a good representation tool for implementing the system directly. We present a transitions-firing process and automatic changes of the number of marks in each box as a firing determination algorithm with the incident matrix and the state transition equation. The convenient analysis and design of a system as well as Computer Aided Design is possible because the operations of an EMFG ran be represented in the mathematical analysis with ease.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2002.10a
• /
• pp.443-446
• /
• 2002

A vehicle oversteered or cornering at excessive speed leaves tire yaw mark on the road surface. A yaw mark is a sign that the tire was sideslipping and exceeded its frictional limit because of centrifugal force. Problems exist with the traditional equation, “critical speed formula (CSF)”, that limits its practical use in traffic accident reconstruction. A major problem is that the equation dose not account for vehicle dynamics and interface between tire and road. The literature refers to that the accuracy of the critical speed formula varies with several factors. New equations that account for vehicle dynamics are introduced in this paper. A comparison of the accuracy of the new method and the traditional method in the calculation of speed is conducted.

• Design & Manufacturing
• /
• v.2 no.2
• /
• pp.33-37
• /
• 2008

This paper describes the optimization of injection molding conditions to minimize sink marks. Sink marks, which refer to a small depression on the surface opposite a thick wall thickness, are often encounted in injection molded plastic parts. Part geometry, material properties and processing conditions during injection molding can affect the sink mark depth. We designed the runner system which is possible balanced filling to cavities using CAE program and then obtained optimal processing conditions by Taguchi's Robust Design technique. By actual injection molding using optimized mold and molding conditions, it confirmed that sink mark depth decreased zero compared to 1mm level in the conventional mold and process.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.41 no.3
• /
• pp.328-330
• /
• 2016

A lane departure warning system based on single lane mark detection is presented in this paper. The proposed system is focused on the robust detection of lane departure, even when one of the left or the right lane mark cannot be detected because of poor illumination or abrasion. Experimental results show that the proposed system warns lane departure, even if only a single lane is detected.

• Transactions of Materials Processing
• /
• v.11 no.8
• /
• pp.691-700
• /
• 2002

Injection molded plastic parts have many surface detects: weld line, sink mark, flow mark, gloss, shading, scratching, and so on. Because these surface faults have not been accepted esthetically, plastic parts are Produced through painting or texturing. The purpose of this paper is to develop a paintless molded part of TV Mask Front by flow control method and gas-assisted injection molding. In order to minimize defects from injection molding, this study was carried out using computer aided injection mold filling simulations using MF/FLOW and MF/GAS. Based on these numerical results, we developed FR(Flame Retardant) HIPS and established guidelines of part design, mold design, and Processing conditions. We have achieved of cost sayings, improvement of productivity, and utilization of recycling by eliminating surface defects and painting process.

• Journal of the Korean Chemical Society
• /
• v.9 no.2
• /
• pp.96-100
• /
• 1965

Possibility on carrier-free Fe-59 preparation by Korean TRIGA Mark Ⅱ reactor was investigated, namely average cross section on $Co^{59}$(n,p) $Fe^{59}$ reaction, separation by anion exchange resin and radiochemical purity. Radiochemical purity of Fe-59 separated was checked by the method of ${\gamma}$-ray spectrometry with 256-multichannel pulse height analyzer and of half life determination. This method permits Fe-59 preparation with radiochemical purity of > 99.9%.

• Proceedings of the Korea Information Processing Society Conference
• /
• 2003.05c
• /
• pp.2073-2076
• /
• 2003

본 논문에서는 이산코사인변환의 선형성을 이용하여 정지화상의 위변조를 방지하기 위한 semi-fragile 워터마킹 방법을 제안하였다. 제안한 방법에서는 이산코사인변환의 선형특성을 이용하여 공간영역에서 임의의 DCT 계수를 변형시킬 수 있으므로 이산코사인변환을 행하지 않고도 워터마킹 정보를 삽입할 수 있으므로 빠른 워터마킹 삽입이 가능하다 또한 정해진 DCT 계수에만 워터마킹 정보를 삽입할 수 있으므로 비가시성의 향상을 가져올 수 있다. 제안한 방법이 압축에 강인함을 실험을 통하여 입증하였다.

• Journal of the Institute of Electronics Engineers of Korea SP
• /
• v.45 no.1
• /
• pp.22-28
• /
• 2008

In this paper, we propose a DCT coefficient domain watermarking scheme, which makes use of the sinusoidal patterns created by the watermark embedding. The embedded watermark can be detected in the spatial domain by computing the correlation. Also, the proposed algorithm can detect the spatial synchronization without additional sync bit embedding. Experimental results show that the proposed algorithm is robust to various StirMark attacks.