• 한국분말재료학회지
• /
• 제11권3호
• /
• pp.247-252
• /
• 2004

Recently, it has been found that mechanical alloying (MA) facilitates the nanocomposites formation of metal-metal oxide systems through solid-state reduction during ball milling. In this work, we studied the MA effect of Fe$_{3}$O$_{4}$-M (M = Al, Ti) systems, where pure metals are used as reducing agents. It is found that composite powders in which $Al_{2}$O$_{3}$ and TiO$_{2}$ are dispersed in $\alpha$-Fe matrix with nano-sized grains are obtained by mechanical alloying of Fe$_{3}$O$_{4}$ with Al and Ti for 25 and 75 hours, respectively. It is suggested that the large negative heat associated with the chemical reduction of magnetite by aluminum is responsible for the shorter MA time for composite powder formation in Fe$_{3}$O$_{4}$-Al system. X-ray diffraction results show that the reduction of magnetite by Al and Ti if a relatively simple reaction, involving one intermediate phase of FeAl$_{2}$O$_{4}$ or Fe$_{3}$Ti$_{3}$O$_{10}$. The average grain size of $\alpha$-Fe in Fe-TiO$_{2}$ composite powders is in the range of 30 nm. From magnetic measurement, we can also obtain indirect information about the details of the solid-state reduction process during MA.

• 한국분말재료학회지
• /
• 제5권2호
• /
• pp.122-128
• /
• 1998

NiAl based ODS (Oxide Dispersion Strengthened) intermetallic alloys have been produced by mechanical alloying (MA) process and consolidated by hot extrusion. Subsequent thermomechanical treatments have been applied to induce secondary recrystallization in an attempt to improve creep resistance in this material. The creep behavior of secondary recrystallized MA NiAl has been investigated and compared with those of as-extruded condition. Minimum creep rate were shown to be approximately two orders of magnitude lower than that in as-extruded condition. The improvement in creep resistance is believed due to the grain coarsening, restricting of dispersoid coarsening as well as increase in grain aspect ratio. Creep threshold stress behavior, below which no measurable creep rate can be detected, has been discussed on the basis of particle-dislocation interaction theory. The threshold stress becomes negligible after secondary recrystallization in MA NiAl, presumably due to dispersoid coarsening and a decrease in grain boundary area during secondary recrystallization.

• 한국분말재료학회지
• /
• 제2권2호
• /
• pp.165-170
• /
• 1995

Alloying behavior of nanocrystalline Al-Ti-(Si) composite powders via mechanical alloying (MA) has been investigated, and the effect of Si on the microstructural changes during MA was discussed. The microstructures of both MA powders and extruded compacts were examined. In Al-Ti system, the solid solutionized nanocrystalline powders could be obtained by MA. On the contrary, fine Si particles were embedded as an elemental state in the matrix of Al-Ti-Si system because of the brittleness and the negligible solid solubility of Si in Al. After hot extrusion, $Al3Ti$ phase was finely precipitated in Al-10fSTi alloy, and Si particles were dissolved to form $(Al, Si)_3Ti$ phase in Al-10%Ti-2%Si alloy.

• 한국분말재료학회지
• /
• 제6권1호
• /
• pp.49-55
• /
• 1999

Al-Cr-Zr nanocomposite metal powders were prepared by mechnical alloying (MA) in order to develop aircraft structure materials with lighter weight and lower cost than the conventional Ti and Ni alloys. The morphological changes and microstrutural evolution of Al-6wt.%Cr-3wt.%Zr nanocomposite metal powders during MA were investigated by SEM, XRD and TEM. The approximately 50$\mu$m sized Al-Cr-Zr nanocomposite metal powders has been formed after 20 h of MA. The individual X-ray diffraction peaks of Al, Cr and Zr were broadened and peak intensitied were decreased as a function of MA time. The observed Al crystallite size by TEM was in the range of 20 nm, which is a simliar value calculated by Scherrer equation. The microhardness of Al-Cr-Zr nanocomposite metal powders increases alomost linearly with increase of the processing time, reaching a saturation hardness value of 127 kg/$mm^2$ after 20 h of processing. The intermetallic compound phase of $Al_3Zr_4$ in the matrix was identifed by XRD and TEM.

• Elastomers and Composites
• /
• 제41권1호
• /
• pp.49-56
• /
• 2006

Allylamine을 이용하여 UV하에서 폐타이어 분말을 개질하였으며, 이를 이용한 PP/폐타이어분말 복합체의 열적, 유변학적 성질을 분석하였다. X-ray 분석결과 무수말레 산이 그라프트된 폴리프로필렌과 같은 상용화제가 없는 경우 ${\beta}$ 결정의 피크 강도가 증가한 반면 상용화제가 있는 경우 완전히 없어짐을 알 수 있었으며, DSC 결과에서도 이를 확인할 수 있었다. 개질된 폐타이어 분말을 함유한 복합체의 용융점도와 탄성모듈러스는 개질되지 않은 분말을 함유한 복합체 보다 높은 값을 나타내었으며, 이는 개질된 분말 표면의 아민기와 말레이산이 그라프트된 PP의 상호작용에 기인하는 것으로 판단된다.

• 한국결정성장학회지
• /
• 제22권1호
• /
• pp.51-56
• /
• 2012

본 연구에서는 출발원료로 ${\sigma}$-VCo 금속간화합물과 $V_{50}Co_{50}$ 혼합분말을 각각 사용하여 기계적 합금화에 따른 비정질화 가능성을 조사하였다. X선 회절에 의해 얻어진 전구조인자 S(Q) 및 동경분포함수 RDF(r)의 결과로부터 볼밀링이 진행됨에 따라 비정질상의 구조적 특징이 분명히 관찰되었다. 120시간 MA 처리에 의하여 두 경우 모두에서 비정질상이 생성됨을 알 수 있었다. 60시간 동안 MA 처리한 $V_{50}Co_{50}$ 분말시료의 열분석 에서는 약 $600^{\circ}C$에 비정질상의 결정화에 의한 발열 peak가 관찰되었다. X선 회절법에 의해 얻어진 전구조인자 및 동경분포함수의 분석으로부터 MA 시간에 따라 출발 결정상은 비정질상의 특징적인 원자구조로 서서히 변화함을 알 수 있었다.

• 한국분말야금학회:학술대회논문집
• /
• 한국분말야금학회 2006년도 춘계학술강연 및 발표대회강연 및 발표논문 초록집
• /
• pp.33-34
• /
• 2006

• 한국분말야금학회:학술대회논문집
• /
• 한국분말야금학회 2004년도 춘계학술강연 및 발표대회 강연 및 발표논문 초록집
• /
• pp.53-54
• /
• 2004

• 한국분말야금학회:학술대회논문집
• /
• 한국분말야금학회 2006년도 Extended Abstracts of 2006 POWDER METALLURGY World Congress Part 1
• /
• pp.299-300
• /
• 2006

Machining of sinter-hardened PM steels provides a challenge for part makers. To facilitate machining of these materials, a new additive (MA) has been developed to increase tool life during the machining process. Hard turning tests were performed to evaluate the effect of this new additive. Sintered compacts with the MA additive were compared to compacts without a machining aid and to compacts that contained the MnS additive. This paper discusses the improvement in machinability with this new additive in sinter-hardenable PM steels.

• 한국분말야금학회:학술대회논문집
• /
• 한국분말야금학회 2006년도 Extended Abstracts of 2006 POWDER METALLURGY World Congress Part2
• /
• pp.1292-1293
• /
• 2006

A non-equilibrium powder metallurgy processing such as an MA/SPS (Mechanical Alloying / Spark Plasma Sintering) process is examined in a Ti-48moll%Al. TiAl intermetallic compound is a potential light-weight/high-temperature structural material. One of the major problems, however, limiting the practical use of the material is its poor workability. From this point, the powder metallurgy (PM) processing route has been attractive alternative of the conventional processing for such material The MA/SPS process is able to apply to a LIGA process. Optimization of the pseudo-superplasticity enables to fabricate micro-parts made of fine grained ceramics composites of TiAl by the LIGA process.