• KSBB Journal
• /
• v.17 no.6
• /
• pp.586-589
• /
• 2002

Lipomyces starkeyi KSM 22 produces dextranase and amylase (DXAMase). The addition of 0.02％ (w/v) 2-deoxy-D-glucose or 0.5% (w/v) glycerol into a 1% (w/v) starch medium increased the final activity of DXAMase produced 2.5 fold or 2.4 fold, respectively, compared to that of a 1% (w/v) starch medium. This activity was similar to that produced with 1% (w/v) dextran. The stability of purified OXAMase at 40$\^{C}$ for 3 weeks was tested using the various enzyme stabilizers. With the addition of 25% (v/v) glycerol, 90.9% of initial activity was left after 3 weeks. For practical use, the addition of 1% (v/v) glycerol with 50 mM of CaCl$_2$ or KH$_2$PO$_4$was adequate and maintained 73.4% of the initial activity under the test conditions used.

• Journal of Biosystems Engineering
• /
• v.12 no.3
• /
• pp.50-56
• /
• 1987

중규모 벼농가에서의 벼건조 및 저장을 위하여, 한국형 개량곳간(크기: $1.8{\times}2.4m$, 높이 : 3.2m, 규모 : 2-4 M/T)을 개발하였다. 송풍기(0.5마력) 및 공기유도닥트를 부착하여 건조 및 aeration이 가능하도록 하였으며, 저장중 양곡손실을 최소한 줄이기 위해 방서용철망, 환풍창 및 구판들을 설치하였다. 그리고 양곡의 입출고가 용이하도록 내리닫이쪽문을 설치하였다. 개발된 개량곳간을 이용하여 1981년, 1982년, 1983년 가을에 각각 수확한 물벼를 수확즉시 건조하였을 때, 기후조건, 수확시기, 수확시의 수분함량, 풍량, 송풍시간, 곳간내에서의 벼의 높이 등에 따라서 차이는 있으나 상온 통풍에 의하여 벼를 잘 건조할 수 있었다. 그리고 건조조건에 따라서 건조양상은 달랐으나 180~352시간의 건조시간이 소요되었으며, 연속 상온통풍에 의하여 건조된 벼의 품질은 비교적 양호하였다.

• Korean Journal of Materials Research
• /
• v.7 no.4
• /
• pp.310-316
• /
• 1997

The effects of carbide and matrix structures on the abrasion wear resistance of multi-component white cast irons with 3.0 mass%C have been studied in this paper. Four different heats were poured in order to obtain the specimens with different combinations of the carbide structures: a basic iron(3.0 mass%C-5.0 mass%Cr-5.0 mass%V-5.0 mass% Mo-12.5mass%W)for M$_{6}$C and M$_{7}$C$_{3}$ carbides, and a Cr free iron(3.0 mass%C-5.0 mass%V-2.5mass%Mo-12.5 mass%W) for MC and M6C carbides. A conventional high Cr free free iron(3.0 mass%C-5.0 mass%V-2.5 mass%Mo-12.5 mass%W) for MC and M6C carbides. A conventional high Cr white cast iron was also poured to compare its wear resistance with those of the multi-component white cast irons. In the as-cast condition, the range of abrasive wear rate(Rw=mg/min) was from 4.15 to 5.98 . The lowest Rw, which means the highest wear resistance, was obtained in the basic iron with nodular MC, lamellar M$_{2}$C and cellular M$_{7}$C$_{3}$ carbides. On the other hand, the Rw of the high Cr white cast iron ranked between the basic iron and the Mo and W free iron. In each alloy, the Rw of air hardened or tempered specimen was lower than that of the as-cast one because of the change of matrix structures by the heat treatments. The Rw of the hear treated speci-mens increased in the order Mo and W free iron, basic iron, Cr free iron, high Cr iron, and V free iron.n.n.n.

• Bulletin of the Korean Mathematical Society
• /
• v.57 no.3
• /
• pp.763-780
• /
• 2020

Let R be a commutative ring. An R-module M is said to be w-flat if Tor ^R₁ (M, N) is GV -torsion for any R-module N. It is known that every flat module is w-flat, but the converse is not true in general. The w-flat dimension of a module is defined in terms of w-flat resolutions. In this paper, we study the w-flat dimension of an injective w-module. To do so, we introduce and study the so-called w-copure (resp., strongly w-copure) flat modules and the w-copure flat dimensions for modules and rings. The relations between the introduced dimensions and other (classical) homological dimensions are discussed. We also study change of rings theorems for the w-copure flat dimension in various contexts. Finally some illustrative examples regarding the introduced concepts are given.

• Journal of the Microelectronics and Packaging Society
• /
• v.17 no.2
• /
• pp.49-54
• /
• 2010

The n-type $Bi_2(Te,Se)_3$ powders were fabricated by melting/grinding method and were hot-pressed in order to compare thermoelectric properties of the hot-pressed specimens with those of the $Bi_2(Te,Se)_3$ ingot. Effects of mechanical milling treatment of the $Bi_2(Te,Se)_3$ powders on thermoelectric characteristics of a hot-pressed specimen were also examined. The hot-pressed $Bi_2(Te,Se)_3$ exhibited power factors of $27.3{\sim}32.3{\times}10^{-4}W/m-K^2$ which were superior to $24.2{\times}10^{-4}W/m-K^2$ of the ingot. The $Bi_2(Te,Se)_3$, hot-pressed after mechanical milling treatment of the powders, possessed a non-dimensional figure-of-merit of 1.02 at $100^{\circ}C$ and exhibited extrinsic-intrinsic transition at $130^{\circ}C$.

• Journal of Korea Foundry Society
• /
• v.17 no.5
• /
• pp.480-487
• /
• 1997

Particle reinforced metal matrix composites(MMCs) via a centrifugal spray-cast deposition(CSD) process were fabricated by injecting second phase particles($Al_2O_3$<40${\mu}m$, W<17.3${\mu}m$) into copper melt on the atomizing disc. Compositing modes were investigated by combining microstructures and mathematical modeling between Cu droplets and the reinforced particles injected. The $Cu/W_P$ powders were shown that the W particles penetrate and get embedded in the Cu droplets. It is considered that the W particles composite preferentially in Cu melt on the atomizing disc. On the other hand, the $Al_2O_3$, particles did not penetrate into the Cu droplets on the atomizing disc but get attached in surface of Cu droplets during the flight. It is considered that the compositing may be attained in the flight distance which the relative velocity between Cu droplet and $Al_2O_3$, particle is maximum. The microstructure of the $Cu/W_P$ and the $Cu/(Al_2O_3)_p$ composite preform was strongly influenced by compositing modes of droplets, and after subsequent deposition it was comprised as it is called the dispersed type and the cell type of microstructure, respectively.

• Advances in Traditional Medicine
• /
• v.5 no.3
• /
• pp.240-245
• /
• 2005

The effect of aqueous and alcoholic extract of seeds of Nigella sativa (N. sativa) was studied on the spontaneous movements of the whole worm (w.w) preparation and nerve muscle (n.m) complex of Setaria cervi (S. cervi). Both the extracts caused inhibition of spontaneous movements of the w.w and n.m complex characterized by initial stimulation followed by irreversible paralysis, with the exception that aqueous extract produced a partially reversible paralysis of w.w preparation. Lesser concentration of both the extracts was required to inhibit the movements of n.m complex than the w.w. Suggesting a cuticular permeability barrier. The lethal concentration $50\;(LC_{50})$ and lethal concentration $90\;(LC_{90})$ were 30 and 55 ng/ml for aqueous and 45 and 60 ng/ml for alcoholic extracts respectively.

• Proceedings of the Korean Institute of IIIuminating and Electrical Installation Engineers Conference
• /
• 2009.10a
• /
• pp.149-151
• /
• 2009

This paper gives a comparative analysis on the luminous efficiency of the bulb type LED lamps. we compare and analyze the measurement values bulb type LED lamps using both photogoniometer and integrating sphere. The volt and watt of one 1map are 220 V and 7 W, respectively. The volt and watt of other one are 100 V and 5.3 W, respectively. the values of those were 79.7 1m/W and 76.9 1m/W in the integrating sphere, respectively. Similarly, the values of those were 80.2 1m/W and 79.3 1m/W on the photogoniometer, respectively. As a result, the value of luminous efficiency can be measured using either integrating sphere or absolute goniometer regardless of the difference in case of bulb type LED lamps.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.39 no.12
• /
• pp.1016-1021
• /
• 2002

Luminescent characteristics of FLs were studied according to the structure of electrode for LCD backlight applications. The luminance and luminous efficiency of the FLs fabricated under same conditions were measured and evaluated as functions of magnitude of applied voltage and widths of external electrode. The luminance and luminous efficiency of CCFL at 12 V were 27600 cd/$m^2$ and 35.3 lm/w, respectively The luminance of EEFLS increased as the widths of external electrode increased, and the luminous efficiency of EEFLS showed to increase to 20 mm of electrode width) and to decrease at wider than 20 m of electrode widths. The luminance and luminous efficiency of EEFL with 20 mm of electrode widths were 21600 cd/$m^2$ and 26500 cd/$m^2$, 35.6 lm/w and 34.8 lm/w at 12 V, 14 V, respectively.

• Korean Journal of Materials Research
• /
• v.9 no.7
• /
• pp.753-759
• /
• 1999

The microstructure and electrical properties of ZNR that W $O_3$ is added in the range 0.5~4.0mol%, were investigated. The major part of W $O_3$ were segregated at the nodal point and W-rich phase was formed. Three crystalline phases, such as W-rich phase (W $O_3$), Bi-rich phase (B $i_2$W $O_{6}$ ), and spinel phase (Z $n_{2.33}$S $b_{0.67}$ $O_4$) were confirmed to be co-existed at the nodal point The average grain size increased in the range 15.5~29.9$\mu\textrm{m}$ with increasing W $O_3$ additive content. Consequently. W $O_3$ acted as a promotion additive of grain growth. As the W $O_3$ additive content increases. the varistor voltage and the nonlinear exponent decreased in the range 186.82~35.87V/mm and 20.90~3.34, respectively, and the leakage current increased in the range of 22.39~83.01 uh. With increasing W $O_3$ additive content, the barrier height and the density of interface states decreased in the range 1.93~0.43eV and (4.38~1.22)$\times$10$^{12}$ $\textrm{cm}^2$, respectively. W $O_3$ acted as an acceptor additive due to the donor concentration increasing in the range (1.06~0.38)$\times$10$^{18}$ /㎤with increasing W $O_3$ additive content.t.t.