• Applied Science and Convergence Technology
• /
• 제26권4호
• /
• pp.70-73
• /
• 2017

The dielectric constant and loss of poling/non-poling was measured in the $Pb_{1-3x/2}La_x[(Mg_{1/3}Ta_{2/3})_{0.66}Zr_{0.34}]O_3$ samples. The addition of $La^{3+}$ to the $Pb_{1-3x/2}La_x[(Mg_{1/3}Ta_{2/3})_{0.66}Zr_{0.34}]O_3$ did not cause a large change in grain size. But the addition of $La^{3+}$ did show transition temperature, which shifted toward low temperature in the $Pb[(Mg_{1/3}Ta_{2/3})Zr]O_3$ systems. In addition, the dielectric and pyroelectric properties (${\varepsilon}{\sim}20000$, $p{\sim}0.03C/m^2K$) of this system using $La^{3+}$ have been greatly improved. Pyroelectrics $Pb_{0.97}La_{0.02}(Mg_{1/3}Ta_{2/3})_{0.66}Zr_{0.34}]O_3$ system was found to have a relatively high ferroelectric FOMs ($F_V{\sim}0.035m^2/C$, $F_D{\sim}0.52{\times}10^{-4}Pa^{-1/2}$) at room temperature. Spontaneous polarization showed a value of $0.27{\sim}0.35C/m^2$ in the composition added to $La^{3+}$. The piezoelectric constant ($d_{33}=350{\sim}490pC/N$) and electromechanical coupling factor ($k_P=0.25{\sim}0.35$) are obtained in $Pb_{1-3x/2}La_x[(Mg_{1/3}Ta_{2/3})_{0.66}Zr_{0.34}]O_3$ compositions with $La^{3+}$ dopant.

• Journal of Electrochemical Science and Technology
• /
• 제11권2호
• /
• pp.117-131
• /
• 2020

The adsorption of N-[(E)-Pyridin-2-ylmethylidene] aniline, a Schiff base, on to mild steel surface in 1M HCl and 0.5 M H₂SO₄ solutions and the consequent corrosion protection were studied employing weight loss method, electrochemical impedance spectroscopy and potentiodynamic polarization measurements. DFT calculations were performed to investigate its interaction with the metal surface at the atomic level to understand its inhibition mechanism. The adsorption process is well described by the Langmuir isotherm. The thermodynamic parameters indicated that the adsorption is spontaneous and the interaction of the inhibitor at the mild steel surface is mainly through physisorption. The R_a values obtained in AFM studies for the uninhibited and inhibited sample in HCl media respectively are 0.756 and 0.559 ㎛, and that in H₂SO₄ media are 0.411 and 0.406 ㎛. The lesser roughness values of the inhibited sample shows the adsorption of the molecules onto the mild surface. The inhibition efficiencies were found to improve with concentration of the inhibitor and the maximum efficiency was observed at 400ppm in all the investigation methods adopted. The inhibitor was found to exhibit a higher efficiency in HCl media (95.7%) than in H₂SO₄ (92.8%). The theoretical and experimental results are found to be in good agreement.

• 폴리머
• /
• 제36권6호
• /
• pp.822-830
• /
• 2012

본 연구에서는 실리카 나노입자를 우수한 내가수분해성을 가지는 dipodal 형태의 bis[3-(trimethoxysilyl)propyl]amine(BTMA) 실란 커플링제로 표면 개질한 후, 실리카에 도입된 BTMA의 2차 아미노기인 N-H기와 마이클 부가반응이 가능한 acrylate기를 1분자당 2개씩 가지는 poly(ethylene glycol)diacrylate(PEGDA)로 표면 처리하여 acrylate기를 실리카 입자 표면에 도입하는 연구를 수행하였다. PEGDA의 몰수 및 3가지 서로 다른 분자량의 PEGDA(M.W. 258, 575, 700) 처리가 실리카 표면에 도입되는 acrylate기의 구조에 미치는 영향을 fourier transform infrared spectroscopy(FTIR), elemental analysis(EA, 원소분석) 및 고체 상태 $^{13}C$ cross-polarization magic angle spinning(CP/MAS) nuclear magnetic resonance spectroscopy(NMR)법을 사용하여 분석하였다. 액체상태의 순수 PEGDA와 순수 BTMA를 같은 몰 비로 반응시키면 PEGDA 1분자당 2개씩 존재하는 acrylate기 중 1개 acrylate기는 순수 BTMA의 N-H기와 1:1의 비율로 마이클 부가반응이 일어나 ${\beta}$-amino acid ester를 형성하고, 나머지 1개의 acrylate기는 남아서 중합반응이 가능한 단량체 합성이 가능하다. 하지만, BTMA로 개질된 실리카 입자를 PEGDA와 반응시키면, PEGDA 1분자당 2개씩 결합있는 acrylate기 대부분이 실리카 입자에 결합되어 있는 BTMA의 N-H기와 마이클 부가반응으로 ${\beta}$-amino acid ester를 형성하여, acrylate기의 C=C기 대부분이 C-C로 변화함을 확인하였다.

• 열처리공학회지
• /
• 제7권1호
• /
• pp.25-34
• /
• 1994

To investigate the effect of austenitizing tempratures on the mechanical properties and corrosion resistance of 0.19%C-13.6%Cr martensitic stainless steel, the changes in martensitic trasformation temperatures, mechanical properties and anodic polarization curve were examined after changing the austenitizing temperatures and tempering temperatures. On increasing heating rate at the same austenitizing temperatures, $A_s$, $A_r$ and $M_s$ increased. And the $M_s$ temperature showed to be decreased with increasing austenitizing temperature. With increasing tempering temperature up to $500^{\circ}C$, strength, hardness and impact value were not changed remarkably, on the other hand the tensile strength and hardness decreased and impact value increased after tempering above $550^{\circ}C$ owing to the $M_{23}C_6$ carbide precipitation. The abrupt decrease in elongation at the tempering temperture of $500^{\circ}C$ proved to the precipitation of $M_7C_3$ carbide. The effect of austenitizing temperature on the mechanical properties of the tempered specimen showed to be decreased in impact value and elongation at the austenitizing temperature of $1150^{\circ}C$. At low tempering temperatures the corrosion resistance of the tempered specimen was not changed obviously with increasing tempering temperature. On the other hand, the resistance decreased above the tempering temperature of $600^{\circ}C$ due to the precipitation of $M_{23}C_6$ carbides. The corrosion resistance showed to be improved with increasing the austenitizing temperature owing to the dissolution of carbides.

• The Korean Journal of Ceramics
• /
• 제6권1호
• /
• pp.74-77
• /
• 2000

Ta-doped PZT thin films prepared by reactive co-sputtering method could be transformed into single grained perovskite structure utilizing physical etching of Pt bottom electrode. It is found that PZT perovskite phase on damaged (111) Pt electrode by IMD was more easily crystallized than random oriented Pt electrode and less crystallized than (111) Pt electrode. This shows that amorphized Pt electrode surface by IMD process has an effect on crystallization of PZT perovskite phase. 40$\mu\textrm{m}\times40\mu\textrm{m}$ square shape single grain PZT array could be obtained utilizing the difference of incubation time for nucleation of rosettes between ion damaged Pt and (111) oriented Pt electrode. Single grained PZT thin films show low leakage current density of $1\times10^{-7}$ A/$\textrm{cm}^2$ and high break down field of 440kV/cm. The loss of remanent polarization after $10^{11}$ cycles was less than 15% of initial value.

• Corrosion Science and Technology
• /
• 제2권4호
• /
• pp.165-170
• /
• 2003

Atmospheric corrosion behaviors of Zn, Zn-5%Al and Zn-55%A l coated steels have been investigated under cyclic wet-dry environments containing chloride ions. The wet-dry cycle was carried out by alternate exposure to immersion in 0.5 M (or 0.05 M) NaCl solutions and drying at $25^{\circ}C$ and 60 %RH. The polarization resistance $R_p$ and solution resistance $R_s$ were monitored by AC impedance technique. From the obtained $1/R_p$ and $1/R_s$ values, the corrosion rate of the coatings and the Time of Wetness (TOW) were estimated, respectively. Effects of chloride ions and TOW on the corrosion rates of Zn, Zn-5%Al, Zn-55%Al coatings and appearance of red rust (onset of underlying steel corrosion) under wet-dry cycles are discussed on the basis of the corrosion monitoring data.

• 대한원격탐사학회:학술대회논문집
• /
• 대한원격탐사학회 2008년도 International Symposium on Remote Sensing
• /
• pp.422-425
• /
• 2008

TerraSAR-X is new radar satellite operated at X-band, multi polarization, and multi beam mode. Compared with C-band or L-band SAR, the X-band system inherently suffers from more temporal decorrelation, but is more sensitive to surface deformation monitoring due to short wavelength (3.1 cm) and high spatial resolution (1m-3m). It is generally expected that sensitivity to estimate surface movement using TerraSAR-X will be increased by the factor of 10, compared to current C-band system with low spatial resolution such as ERS-2, Envisat. Many urban areas are experiencing land subsidence due to water, oil and natural gas withdrawal, underground excavation, sediment compaction, and so on. Monitoring of surface deformation is valuable for effectively limiting damage areas. In addition high accuracy and spatially dense subsidence map can be achieved by X-band InSAR observation, promoting identification and separation of various subsidence processes and leading to enhanced understanding via mechanical modeling. In this study we will introduce some initial InSAR results using new TerraSAR-X SAR data for surface deformation monitoring.

• 한국표면공학회:학술대회논문집
• /
• 한국표면공학회 2009년도 춘계학술대회 논문집
• /
• pp.217-218
• /
• 2009

최근 경량화, 리사이클성, 기기의 소형화, 내환경성 등의 이점을 가지고 있는 알루미늄 합금이 여러 분야서 재인식 되고 있다. 그러나 이런 알루미늄 합금이 부식 환경에 노출 될 경우 음력부식균열이 발생할 수 있게 된다. 이러한 음력부식균열의 발생은 알루미늄의 기계적 특성에 안 좋은 영향을 미치므로 제품의 품질저하, 수명 단축, 효율저하, 재해발생 등 직간접적으로 광범위한 피해를 입게 되기에 부식에 대한 많은 연구가 진행이 되고 있다. 이 중에 고비강도용 알루미늄 압출소재인 Al 6xxx계 합금의 열처리 및 조성 변화에 따른 음력부식 균열의 거동에 대해 연구하였다. 응력부식균열 시험은 SSRT시험으로 많이 하고 있는데, 이 시험은 인장시편을 부식 환경 하에 노출하면서 천천히 일정한 변형속도로 당기는 시험이다. 본 연구에서는 Strain rate를 ${10^{-6}}s^{-1}$ 부식용액은 1M-NaCl + 0.6M-$Na_{2}SO_{4}$ + 0.3%-$H_{2}O_{2}$을 사용하여 시험을 하였다. 그러나 시험에 대한 분석은 Tafel polarization curve, SEM, OMS를 이용하였다.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2005년도 제36회 하계학술대회 논문집 C
• /
• pp.2022-2024
• /
• 2005

Electrical double-layer capacitor (EDLC) is an electrochemical energy storage device in which electric charges only accumulated by a pure electrostatic attraction force are stored on the electrolyte-electrode interface in a form of double layer and separated by the electrolyte. The composite was prepared by mixing nanosize $TiO_2$ and activated carbon through a means of ultrasonic vibration in ethanol solution for 30 min in various mass ratios of $AC:TiO_2$ to form activated carbone-semiconducting oxide composites. Either 1.0 M $LiClO_4/EC-DEC$ or $Et_4NBF_4$/EC-DEC was used as the electrolyte. It was found that with modification of $TiO_2$, the specific capacitance of activated carbon measured at $1mA/cm^2$ was increased from 40 to 50 F/g. This method is unique in comparison the conventional method because it uses semiconducting TiO2 other than electrochemically active materials such as $RuO_2$. The increase in specific capacitance could be attributed to the decrease in electric polarization, caused by the introduction of $RuO_2$.

• 대한기계학회논문집A
• /
• 제25권6호
• /
• pp.965-971
• /
• 2001

To estimate the reliability of 12Cr alloy steel, the material of turbine blade in the steam power plant, Its corrosion susceptibility and fatigue characteristics in NaCl and Na$_2$SO$_4$solution with the difference of concentration and temperature was investigated. The polarization tests recommended in ASTM G5 standard for corrosion susceptibility in the various corrosive solutions was estimated. It showed that the higher temperature, the faster corrosion rates and corrosion rates were the fastest in 3.5 wt.% NaCl and 1M Na$_2$SO$_4$solution. From these results, the degradation conditions were determined in distilled water, 3.5 wt.% NaCl and 1M Na$_2$SO$_4$solution at room temperature, 60$\^{C}$ and 90$\^{C}$ during 3, 6 and 9 months. Its surface had a few pits for long duration. But, it was not susceptible in sulfide and chloride condition of several temperatures. If the degraded 12Cr alloy steel and non-degraded one were compared with fatigue characteristics, Any differences were not found regardless of temperature and degradation period.