• Bulletin of the Korean Chemical Society
• /
• v.32 no.10
• /
• pp.3682-3686
• /
• 2011

The electrochemical properties of lithium-sulfur batteries with binary electrolytes based on DME and DOL, TEGDME and DOL mixed solvent containing $LiClO_4$, LiTFSI, and LiTF salts were investigated. The ionic conductivity of 1M LiTFSI and $LiClO_4$ electrolytes based on TEGDME and DOL increased as the volume ratio of DOL solvent increased, because DOL effectively reduces the viscosity of the above electrolytes medium under the same salts concentration. The first discharge capacity of lithium-sulfur batteries in the DME and DOL-based electrolyte followed this order: LiTFSI (1,000 mAh/g) > LiTF (850 mAh/g) > $LiClO_4$ (750 mAh/g). In case of the electrolyte based on TEGDME and DOL, the first discharge capacity of batteries followed this order: $LiClO_4$ (1,030 mAh/g) > LiTF (770 mAh/g) > LiTFSI (750 mAh/g). The cyclic efficiency of lithium-sulfur batteries at 1M $LiClO_4$ electrolytes is higher than that of batteries at other lithium salts-based electrolytes. Lithium-sulfur battery showed discharge capacity of 550 mAh/g until 20 cycles at all electrolytes based on DME and DOL solvent. By contrast, the discharge capacity of batteries was about 450 mAh/g at 1M LiTFSI and LiTF electrolytes based on TEGDME and DOL solvent after 20 cycles.

• Proceedings of the Korean Society of Marine Engineers Conference
• /
• 2005.11a
• /
• pp.236-237
• /
• 2005

An experimental study on the Hybrid Cooling Tower has been done having a rated capacity of 3RT. Counter flow type fill, cross flow type fill and hybrid-type fill which is combined with two type fills as previously stated having a height of 0.3m have been used in the 0.8m${\times}$0.4m${\times}$1.9m dimensional tower respectively. The heat exchanger is consisting of 2 or 3 rows. The relevant temperatures and the velocities were selected based on the typical Korean weather for the year round operation of the tower. The cooling capacity of the tower is explained with respect to varying air inlet velocities, wet-bulb temperatures, and air to cooling water volume flow rate ratio (L/G ratio). The capacity of the hybrid-type fill was much superior to other fills, but hybrid-type fill shows higher pressure drop.

• Journal of Nutrition and Health
• /
• v.24 no.5
• /
• pp.399-407
• /
• 1991

The purpose of this study was to estimate the intake of individual fatty acid and eventually to contribute to the establishment of dietary guidelines and recommendations of fatty acids for the Koreans. The subjects consisted of female college students aged 20 to 29 years old. Their dietary intake was assessed twice. in summer and in winter, by means of a 24-hour dietary recall method. Food models and other measuring tools were also used. Concentrations of serm total triglyceride, total cholesterol and HDL-& LDL-cholesterol were measured. The subjects consumed 12.3g of polyunsaturated fatty acids, 14.3g of monounsaturated fatty acids and 14.99g of saturated fatty acids per day The ratios of polyunsaturated/saturated fatty acids( P/S) and polyunsaturatedimonounsaturatedi saturated fatty acids (P/M/S) taken by the subjects were 0.8/1.0 and 0.8/l.0/l.0, respectively. The ratio of w61w3 fatty acids was found to be 8.3/l.0. All of these values seem to fall in the desirable range. The percentages of total calorie from carbohydrate. fat and protein were 59.4%, 23.4% and 17.2%, respectively. The concentrations of serum total triglyceride, total cholesterol. HDL-cholesterol and LDL-cholesterol were 59.3ms/dl, 192.7mg/dl, and 59.0mg/dl, and 121.9mg/dl., respectively.

• Journal of Biosystems Engineering
• /
• v.37 no.1
• /
• pp.58-64
• /
• 2012

Purpose: The objective of this study was to investigate the feasibility of anaerobic digestion of Chinese cabbage waste juice (CCWJ) and swine manure(SM). Methods: The anaerobic digestion test was conducted under batch and continuous conditions at mesophilic temperature ($36-38^{\circ}C$). The batch test was divided into Experiment I and II. In the Experiment I, biogas potential and production rate of CCWJ was evaluated. In Experiment II the effect of F/M ratio (2.0, 3.2, 4.9) at mixture ratio of 25:75(CCWJ: SM, % vol. basis) on biogas yield was studied. Results: CCWJ produced biogas and methane yield of 929 and 700 mL/g VS added respectively. The biogas yield from the mixture of CCWJ and SM was almost same at F/M ratio of 2.0 and 3.2 but dropped by 14% when F/M ratio increased from 3.2 to 4.9. In continuous test the mixture of CCWJ and SM (25:75, % vol. basis) produced biogas yield of 352 mL/g VS added which is around 11% higher compared to biogas yield from SM alone. Addition to biogas yield digester performance was also improved with co-digestion of CCWJ with SM. Conclusions: The results showed that the anaerobic digestion of CCWJ with SM could be promising for improving both the biogas yield and digester performance at mesophilic temperature.

• BMB Reports
• /
• v.30 no.5
• /
• pp.346-351
• /
• 1997

The maximum adsorption/desorption conditions and the adsorption mechanism of globular proteins to vaccine adjuvants were determined. The maximum adsorption ratio of protein to the $Al^{3+}$ content of aluminum oxyhydroxide and the optimal adsorption pH are 2:1 (${\mu}g:{\mu}g$) for bovine serum albumin (BSA) at pH 6.0 and 2.5:1 (${\mu}g:{\mu}g$) for immunoglobulin G (IgG) at pH 7.0, respectively. The maximum adsorption ratio onto aluminum phosphate gel was 1.5:1 (${\mu}g$ Protein:${\mu}g$ $Al^{3+}$) at pH 5.0 for both BSA and IgG. Adsorption of the native globular proteins, BSA and IgG, to aluminum oxyhydroxide and aluminum phosphate gel was reversible as a function of pH. Complete desorption of these proteins from aluminum phosphate gel was observed at alkaline pH, whereas only 80~90% removal from aluminum oxyhydroxide was achieved with alkaline pH and 50 mM phosphate buffer. We conclude that electrostatic and hydrogen bonding interactions between the native proteins and adjuvants are important binding mechanisms for adsorption, and that the surface charge of the protein and the colloid components control the maximum adsorption conditions.

• Journal of Environmental Science International
• /
• v.26 no.1
• /
• pp.29-36
• /
• 2017

Aerosol mass size distributions were investigated at 865 m high the of Jirisan national park. A nanosampler cascade impactor was used to collect aerosols. The atmospheric aerosol particles had a unimodal mass size distribution, which peaked at $0.5-1.0{\mu}m$, and a mass aerodynamic diameter of $1.13{\mu}m$. The annual average concentrations of TSP, $PM_{10}$, $PM_{2.5}$, $PM_1$, $PM_{0.5}$ and $PM_{0.1}$ were $20.9{\mu}g/m^3$, $19.3{\mu}g/m^3$, $14.9{\mu}g/m^3$, $10.7{\mu}g/m^3$, $5.3{\mu}g/m^3$, $1.2{\mu}g/m^3$, respectively. TSP concentrations were below $30{\mu}g/m^3$ during the sampling period. On average $PM_{10}$, $PM_{2.5}$, $PM_1$, $PM_{0.5}$ and $PM_{0.1}$ made up 0.91, 0.70, 0.41, 0.19 and 0.07 of TSP, respectively. The annual average of PM2.5/PM10 ratio was 0.77.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.19 no.1
• /
• pp.9-16
• /
• 2013

The growth and production of Aulichthys japonicus (6.70~15.32 cm TL) were investigated in an eelgrass bed of Dongdae Bay, Korea throughout 2006. A total 888 A. japonicus were collected with a small beam trawl. Growth in fish total length was expressed by the von Bertalanffy's growth equation as: $L_t=24.8257(1-e^{-0.5583(t+0.4816)})$. The densities, biomass, daily, annual production, and P/B ratio were $0.01{\pm}0.009/m^{-2}$, $0.17{\pm}0.16g/m^2$, $0.00006{\pm}0.00006g$ AFDW/$m^2$/day, 0.02g AFDW/$m^2$/yr, and 0.12, respectively. Monthly variation in production of A. japonicus was large; the peak occurred at July, September and November 2006 (0.000182, 0.000127 and 0.000123 g AFDW/$m^2$/day), where as the lowest value was 0.000003g AFDW/$m^2$/day at April and May 2006. Monthly change in production of A. japonicus was positive correlated with number of individuals, biomass and growth rate.

• Journal of Biomedical Engineering Research
• /
• v.23 no.6
• /
• pp.451-458
• /
• 2002

Osteoporosis is a systemic skeletal disease caused by low bone mass and the decrease of bone density in the microstructure of trabecular bone. Drug therapy(PTH Parathyroid hormone) may increase the trabecular thickness and thus bone strength. Vertebroplasty is a minimally invasive surgery foy the treatment of osteoporotic vertebral compression fracture. This Procedure includes Puncturing vertebrae and filling with Polymethylmethacrylate(PMMA). Although altering recommended monomer-to-Powder ratio affects material properties of bone cement, clinicians commonly alter the mixture ratio to decrease viscosity and increase the working time. The Purposes of this study were to analyze the effect of 4he monomer-to-powder ratio on the mechanical characteristics of trabecular. In this paper, the finite element model of human vertebral trabecualr bone was developed by modified Voronoi diagram, to analyze the relative effect of hormone therapy and vertebroplasty at the treatment of osteoporotic vertebrae. Trabeuclar bone models for vertebroplasty with varied monomer-to-Powder ratio(0.40∼1.07 ㎖/g) were analyzed. Effective modulus and strength of bone cement-treated models were approximately 60% of those of intact models and these are almost twice the values of hormone-treated models. The bone cement models with the ratio of 0.53㎖/g have the maximum modulus and strength. For the ratio of 1.07㎖/g, the modulus and strength were minimum(42% and 49% respectively) but these were greater than those for drug therapy. This study shows that bone cement treatment is more effective than drug therapy. It is found that in vertebroplasty, using a monomer-to-powder ratio different from that recommended by manufacturer nay significantly not only reduce the cement's material Properties but also deteriorate the mechanical characteristics of osteoporotic vertebrae.

• Korean Chemical Engineering Research
• /
• v.46 no.5
• /
• pp.880-885
• /
• 2008

Spray pyrolysis was applied to prepare spherical silica particles with mesopores of a regular structure. The physical properties such as surface area, pore size, pore structure, particle size, and morphology were studied by BET, SEM, SAXS, and DLS analysis. At a fixed gas flow rate, the BET surface area changed from 200 to $1,290m^2/g$ as changing the CTAB/TEOS molar ratio from 0.05 to 0.3. At a fixed CTAB/TEOS ratio, the surface area of silica particles was varied from 1,062 to $1,305m^2/g$ with changing the gas flow rate from 10 to 40 l/min. The average pore size measured by BJH desorption was about $21{\sim}23{\AA}$ and not significantly influenced by the CTAB/TEOS ratio and the gas flow rate. Finally, the highest surface area which was $1,305m^2/g$ were obtained when the CTAB/TEOS ratio and the gas flow rate were 0.2 and 20 l/min, respectively. According to SAXS analysis, the prepared silica particles showed a strong peak at $2{\theta}=2.6^{\circ}$ and two minor peaks around $2{\theta}=4.4^{\circ}$ and $5.1^{\circ}$, which are due to regular mesopores of hexagonal structure. The morphology of silica particles prepared were spherical shape and the average particle size was $1.0{\mu}m$.

• Journal of Korean Society for Atmospheric Environment
• /
• v.9 no.4
• /
• pp.310-319
• /
• 1993

A pilot study was conducted in order to investigate the concentrations of indoor and outdoor VOCs (Volatile Organic Compounds) at ten homes and four building offices in Seoul during March-April, 1993. The five components of VOCs(Benzene, Toluene, Ethylbenzene, o-Xylene, m/p-Xylene) were collected using charcoal tube and were analysed using Gas Chromatography(GC) with a Flame Ionization Detector(FID). The mean concentations of indoor VOCs were shown as Benzene of 38.9 .mu.g/m$^{3}$. Toluene of 165.0 .mu.g/m$^{3}$, Ethylbenzene of 21.7 .mu.g/m$^{3}$, o-Xylene of 11.6 .mu.g/m$^{3}$ and m/p-Xylene of 29.3 .mu.g/m$^{3}$, but those corresponding that indoor levels of VOCs were higher than corresponding outdoor levels. The ratio of indoor and outdoor VOCs were higher than corresponding outdoor levels. The ratio of indoor and outdoor VOCs concentrations was 0.99 for Benzene, 1.23 for Toluene, 5.86 for Ethylbenzene, 5.23 for o-Xylene, 2.41 for m/p-Xylene in homes, while 2.02 for Benzene, 1.15 for Toulene, 0.96 for Ethylbenzene, 1.41 for o-Xylene, 1.38 for m/p-Xylene in offices, respectively. The mean concentrations of VOCs in homes were higher than those levels in offices, while the mean concentration of VOCs during active hour of occupants in a day were higher 1-3 times than the levels during non-active hour. Comparing VOCs levels by building's age, the mean concentrations of Benzene, o-Xylene and m/p-Xylene were higher in new building than old building, but the mean concentrations of Toluene and Etylbenzene in new building were lower than old building. The mean concentrations in all components of VOCs in smoking area were higher than non-smoking area. These results suggested that the VOC levels were affected by various indoor characteristics and behavioral activity of occupants.