• 한국산업융합학회 논문집
• /
• 제10권1호
• /
• pp.5-14
• /
• 2007

It is necessary for development of drawing product with press to have suitable material selection & all process design and the problem during press process has been cleared from judgement of experience & trial and error. Recently we can estimate press process result from computer aided design & FEM. But we can get more reliable result when we can put more precise process variants during FEM. In case of using a drawbead that is used for the material inflow, it is considered for us to put material property, other analysis condition & friction figure when material is passing through the drawbead for better FEM. From our study, we have drawn an analogy bead connection depth, friction figure & drawing and restraining load according to kinds of lubrication from experiment & FEM for the drawbead. We applied above result to the drawing experiment & FEM and confirmed the validity. We could notice the relation between friction figure & drawing load and the friction figure variation according to kinds of lubrication. It is expected to draw more precise analogy that can be used for real process due to more precise process variants application to FEM.

• Tribology and Lubricants
• /
• 제38권6호
• /
• pp.261-266
• /
• 2022

Notably, laser surface patterning facilitates tribological applications under lubricated sliding contacts. Consequently, a special pattern that can reduce the coefficient of friction under contact is considered necessary for improved machine efficiency. However, inappropriate pattern designs produce higher friction coefficients and cannot reduce friction. In this study, we use cast iron pins as specimens to investigate their friction and wear characteristics. Moreover, we experimentally investigate the correlation between the friction reduction effect and the design of groove crosshatch patterns fabricated with various angles and widths. We conduct a friction test using a pin-on-disc type tribometer under grease lubrication to study the friction reduction effect of the specimens, and we observe that the average coefficient of friction changes with the crosshatch angle and width. The experiment reveals that grooved crosshatch specimens with a crosshatch angle of 135°maximize friction reduction. The coefficient of friction of the groove specimens with a width of 120 ㎛ is lower than that of the specimens with a width of 200?. The friction reduction effect of the width of the groove is attributed to the density of the groove pattern. Thus, grooved crosshatch patterns can be designed to maximize friction reduction, and the friction property of a grooved crosshatch pattern is found to be related to its width and angle.

• Tribology and Lubricants
• /
• 제39권4호
• /
• pp.148-153
• /
• 2023

Laser surface dimple patterning is a method of laser surface texturing to reduce lubrication sliding friction. The dimple pattern improves friction properties by reserving lubricant and trapping worn particles. This surface texturing technology can reduce coefficients of friction and extend the service life by applying a uniform load to the surface of the material. This study investigates the friction properties using PMMA, a highly compatible polymer material, as a specimen. We observe the friction properties of untextured specimens by processing specimens with dimple pattern densities of 5 and 10 on the surface area using laser. Dimple pattern density affects the coefficient of friction. We present the following friction property results using a pin-on-disc sliding friction test under saline lubrication. The coefficients of friction for the dimple patterned specimens are lower than those for the untextured specimens. As the normal load and sliding speed increase, the coefficients of friction of the dimple pattern specimens decrease differently from those of the untextured specimens. The specimen with a dimple pattern density of 5 at a normal load of 24.5 N and a sliding speed of 0.22 m/s has the best friction properties. Notably, different friction properties are exhibited depending on the dimple pattern densities.

• 한국자동차공학회논문집
• /
• 제22권7호
• /
• pp.48-56
• /
• 2014

Engine oil is an oil used for lubrication of various internal combustion engines. The main function is to reduce wear on moving parts; it also cleans, inhibits corrosion, improves sealing, and cools the engine by carrying heat away from moving parts. In engines, there are parts which move against each other. Otherwise, the friction wastes the useful power by converting the kinetic energy to heat. Those parts were worn away, which could lead to lower efficiency and degradation of the engine. It increases fuel consumption, decreases power output, and can induce the engine failure. This study was conducted to evaluate the relation between engine oil property changes and engine performance for the diesel engine. This test was performed by using 12L, 6 cylinder, heavy duty engines. Low SAPS 10W30 engine oil (two type engine oils) was used. Test procedure and method was in accordance with the modified CEC L-57-T97 (OM441LA) method. In this study, TAN, TBN, KV and metal components, engine power, blowby gas, A_F were presented to evaluate the relation with engine oil property changes and engine performance. TAN, TBN, KV and metal We found that the components were generally increased but engine performance did not change. This results mean that property changes did not affect on engine performance because those were not enough to affect engine performance.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 2002년도 proceedings of the second asia international conference on tribology
• /
• pp.443-444
• /
• 2002

The uniformity of field oxide is critical to isolation property of device in STI, so the control of field oxide thickness in STI-CMP becomes enormously important. The loss of field oxide in shallow trench isolation comes mainly from dishing and erosion in STI-CMP. In this paper, the effect of slurries on the dishing was investigated with both blanket and patterned wafers were selected to measure the removal rate, selectivity and dishing amount. Dishing was a strong function of pattern spacing and types of slurries. Dishing was significantly decreased with decreasing pattern spacing for both slurries. Significantly lower dishing with ceria based slurry than with silica based slurry were achieved when narrow pattern spacing were used. Possible dishing mechanism with two different slurries were discussed based on the observed experimental results.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 2002년도 proceedings of the second asia international conference on tribology
• /
• pp.173-174
• /
• 2002

To study the effects of mating materials on the tribological properties of DLC films. we used a ball-on-plate reciprocating friction tester in dry air and mating materials of martensite stainless steel (hardened, annealed SUS440C), austenite stainless steels (SUS304), and bearing steel (hardened, annealed SUJ2). At a light load of 0.6 N, the friction coefficient always exceeded ${\mu}>0.3$. Tribological properties of DLC film were still excellent above 0.6 N, except in sliding against annealed SUJ2. Analysis using micro-laser Raman spectroscopy showed that the difference between annealed SUJ2 and others materials appears mainly due to structural change in film.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2002년도 춘계학술대회 논문집
• /
• pp.223-238
• /
• 2002

This paper presented on an environment estimation of cutting fluid which is a mouse model of acute bacterial rhinosinusitis using cutting fluid in grinding and cutting. Above results will be remarked the necessity of friendly environmental cutting skill when it had used in workshop. The results of a mouse experimental using cutting fluid showed that it are occurred to the respiratory organs sickness. Also cutting fluid are occurred to hurtfulness a person when it used to grinding and cutting in workshop. Also, the results of grinding experiments in avitation materials showed that surface roughness are superior to more emulsion type oil than vegetable type oil according to increase of the depth of cut. Grinding force are similar to both emulsion type oil and vegetable type oil.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2001년도 춘계학술대회 논문집
• /
• pp.24-27
• /
• 2001

Friction between the sheet and tools is one of the important factors affecting the sheet metal forming. Therefore, the clarification of the friction is essential to improve the formability of the sheet. In order to find the effect of material property and lubricant viscosity on the frictional characteristics, tensile test, surface roughness test and friction test are performed. The results showed that friction characteristics are mainly influenced by the surface roughness and lubricant viscosity. A mathematical model of the friction is developed for calculating friction coefficient in terms of surface roughness and lubricant viscosity. The validity and accuracy of the mathematical model of the friction are verified through the experiment and FEM analysis.

• 동력기계공학회지
• /
• 제15권6호
• /
• pp.81-85
• /
• 2011

Because of excellent mechanical properties, such as good friction coefficient and heat resistance characteristics, PTFE parts have been widely used in the industries. However, the poor wear resistance of PTFE has been a main problem limiting wider applications. In this study, to improve the poor wear resistance of PTFE, porous PTFE composites were prepared by mixing additives(sodium bicarbonate and graphite) with PTFE powder. The friction coefficient, wear resistance and lubricating property of porous PTFE composites were measured and the results were compared with those of untreated PTFE.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 1998년도 제28회 추계학술대회
• /
• pp.91-99
• /
• 1998

A correlation between the low-cycle fatigue life and the scuffing-failure life is demonstrated using the plastic strain in boundary lubricated sliding. Loadings proportional to hardness with three different lubricated conditions were used to evaluate the plastic strain. As the results of scuffing tests using vacuum pump oils in nitrogen gas, plastic strain shows 0.0062, and In the mineral oils and commercial engine oils in air, plastic strain show 0.0042 and 0.00092. Those are very useful to describe quantitatively the real lubricated sliding conditions, and are very effective to find the relation between the low-cycle fatigue life and the scuffing life.