• International Journal of Precision Engineering and Manufacturing
• /
• v.5 no.4
• /
• pp.5-13
• /
• 2004

This study explains the effects of lubricant and surface treatment on the life of hot forging dies. The thermal load and thermal softening, that occur when there is contact between the hotter billet and the cooler dies in hot forging, cause wear, thermal cracking and fatigue, and plastic deformation. Because the cooling effect and low friction are essential to the long life of dies, the proper selection of lubricant and surface treatment is very important in hot forging process. The two main factors that decide friction and heat transfer conditions are lubricant and surface treatment, which are directly related to friction factor and surface heat transfer coefficient. Experiments were performed for obtaining the friction factors and the surface heat transfer coefficients in different lubricants and surface treatments. For lubrication, oil-base and water-base graphite lubricants were used, and ion-nitride and carbon-nitride were used as surface treatment conditions. The methods for estimating die service life that are suggested in this study were applied to a finisher die during the hot forging of an automobile part. The new techniques developed in this study for estimating die service life can be used to develop more feasible ways to improve die service life in the hot forging process.

• Applied Chemistry for Engineering
• /
• v.29 no.5
• /
• pp.533-540
• /
• 2018

Graphene has been reported to be an excellent lubricant additive that reduces friction and wear when coated on the surface of various materials or when dispersed in lubricants as an atomic thin material with the low surface energy. In this study, alkyl functionalized graphene oxide (FGO) nanosheets for oil-based lubricant additives were prepared by using three types of alkyl chloride chemicals (butyl chloride, octyl chloride, and tetradecyl chloride). The chemical and structural properties of the synthesized FGOs were analyzed by Fourier transform infrared (FT-IR), X-ray photoelectron spectroscopy (XPS), X-ray diffraction (XRD), Raman spectroscopy, scanning electron microscope (SEM), and transmission electron microscope (TEM). The synthesized FGOs were dispersed at 0.02 wt% in PAO-0W40 oil and its tribological characteristics were investigated using a high frequency friction/wear tester. The friction coefficient and the wear track width of poly alpha olefin (PAO) oil added with FGO-14 were tested by a ball-on-disk method, and the measured results were reduced by ~5.88 and ~3.8%, respectively compared with those of the conventional PAO oil. Thus, it was found that the wear resistance of PAO oil was improved. In this study, we demonstrated the successful functionalization of GO as well as the improvement of dispersion stability and tribological characteristics of FGOs based on various alkyl chain lengths.

• Applied Chemistry for Engineering
• /
• v.34 no.4
• /
• pp.434-443
• /
• 2023

We have investigated the performance improvement of grease by synthesizing calcium sulfonate grease as an alternative to lithium grease, which is widely used globally. Since the composition ratio of the grease, when manufactured, is usually 50% base oil and 50% thickener, using grease as a lubricant in a cryogenic environment is not encouraged due to its inferior low-temperature performance. In this study, we have synthesized three types of calcium sulfonate grease with paraffin oil and PAO-based base oil and thickener. Furthermore, lithium grease was synthesized via saponification with PAO-based base oil, lithium hydroxide, 12-hydroxystearic acid, and sebacic acid. We have measured low-temperature characteristics using a rheometer and low-temperature torque meter, and tribology characteristics were obtained using a four-ball lubricant tester and schwingung reibung verschleiß (SRV). As a result, the flow point of the calcium sulfonate grease synthesized with a PAO-based base oil and thickener was found to be -40℃, overcoming the existing calcium sulfonate grease's low-temperature limitation. Moreover, the synthesized calcium sulfonate grease showed low-temperature performance similar to that of lithium grease synthesized with PAO base oil, but superior anti-wear, extreme pressure, coefficient of friction, heat resistance, adhesion, and corrosion resistance. It is thus expected to commercially replace the existing lithium grease.

• Journal of Soil and Groundwater Environment
• /
• v.13 no.2
• /
• pp.30-35
• /
• 2008

In this study, the feasibility of soil washing, chemical oxidation and sonication was investigated to treat lubricantcontaminated railroad soil. Tergitol, a non-ionic surfactant, was used as a washing agent with or without iso-propyl acohol as a cosolvent. However, it was not effective to remove lubricant from soil even though tergitol was the most effective washing agent for diesel-contaminated soil. The cosolvent reduced the overall washing efficiency. Chemical oxidation removed 30% of lubricant from contaminated soil. Soil washing after chemical oxidation extracted additionally 16-17% of lubricant. Sonication enhanced-soil washing showed enhanced overall efficiency of soil washing. Lubricant-contaminated soil should be remediated by the other technology used for diesel-contaminated soil.

• Journal of Energy Engineering
• /
• v.26 no.3
• /
• pp.131-136
• /
• 2017

Automobile engine oil is the most important lubricant for operating as the engine is started. Recently, manufacturers of the automotive industry and lubricants are considerably improving the quality of oil with additive to extend change cycle period. Most customers are recommended genuine oil among different types from shop expert. Through this report we suggest another reference point for consumer to pick highly efficient lubricant. This report is investigated oil compounds to compare with 6 different automotive considering actual running condition for 7 months. we conducted experiment from physical and chemical perspectives. In the field, through various experiments oil compounds between mineral oil and synthetic oil are largely distinguished in oxidation, viscosity, fluid and TBN. These are influenced by engine part wear as piston, bearing etc. Comparing various investigation with different oil the performance of synthetic oil is shown better condition in flash point, oxidation stability and also found less in change pollutant iron, Al compounds. Additives of oil show clear difference Ca level in detergent-dispersant both mineral oil and synthetic oil. And Zn in extreme pressure additives and P in Lubricity improver make no difference to both.

• Tribology and Lubricants
• /
• v.31 no.6
• /
• pp.245-250
• /
• 2015

This study investigates the lubrication characteristics of fuel injection pumps with reference to different fuel oils. Medium-speed diesel engines use fuel oils with various viscosities, such as heavy fuel oil (HFO, which is a high-viscosity fuel oil) and light diesel oil (LDO, which is a low-viscosity fuel oil). When fuel oil with a low viscosity is used, both fuel oil and lubricating oil lubricate the system. Thus, the lubrication of the fuel injection pump is in a multi-viscosity condition when the fuel oil in use changes. We suggest three cases of multi-viscosity models, and divide the fuel injection pump into three lubrication sections: a, the new oil section; b, the mixed oil section; and c, the used oil section. This study compares the lubrication characteristics with variation of the multi-viscosity model, clearance. The volume of Section b does not affect the lubrication characteristics. The lubrication characteristics of the fuel injection pump are poor when high-viscosity fuel oil transfers to low-viscosity fuel oil. This occurs because the viscosity in the new oil section (i.e., Section a) dominates the lubrication characteristics of the fuel injection pump. However, the lubricant oil supply in the used oil section (i.e., Section c) can improve the lubrication characteristics in this condition. Moreover, the clearances of the stem and head significantly influence the lubrication characteristics when the fuel oil changes.

• International Journal of Air-Conditioning and Refrigeration
• /
• v.17 no.3
• /
• pp.88-93
• /
• 2009

Lubricant oil is needed in air conditioning and refrigeration system because the compressor requires oil to prevent surface to surface contact between its moving parts, to remove heat, to provide sealing, to keep out contaminants, to prevent corrosion, and to dispose of debris created by wear. Thus, the oil separation in an oil separator is one of the most important characteristics for proper compressor operation. In this study, a gravity type of oil separator is used. Oil separation characteristics have been investigated for $CO_2$/PAG mixture in the range of oil concentration 0 to 5 weight-percent and the mixture temperature range of $0^{\circ}C$ to $15^{\circ}C$ at 50 bar and $70^{\circ}C$ to $90^{\circ}C$ at 80 bar. The results obtained indicate that the oil separation is increased with an increase in the oil concentration. It is also found that the oil separation in liquid state is increased with an increase in the mixture temperature while the oil separation in gas state is decreased.

• Journal of Powder Materials
• /
• v.18 no.5
• /
• pp.417-422
• /
• 2011

Hydrophobic nanodiamond (ND) were dispersed in engine oil (Helix Oil, Shell co.) as an additives to improve tribology properties. In this study, nanodiamond prepared by an explosive method was used. Tribology properties of both pure Helix oil and engine oil containing ND additive were evaluated. The rotating disks were made of Gray Cast Iron (240 Hv) and SKD11 (710 Hv). Surface topographies of the disks' wear tracks and friction coefficient were compared. The results show that nanodiamond-dispersed lubricants are capable of reducing these metals' wear loss. The friction coefficient is strongly affected to the hardness of wear track.

• Tribology and Lubricants
• /
• v.31 no.5
• /
• pp.195-204
• /
• 2015

Several researches are focused on improving the value of fine chemicals based on biomass resources due to environmental and other concerns associated with the use of petroleum-based products. Therefore, the synthesis and application of estolides derived from plant-based waste oil materials and their application as lubricants and as processing oil for butyl rubber products have been studied. Four kinds of estolide were prepared with conversions of 71~92% over 24h using various vegetable oils, as determined by size exclusion chromatography (SEC) and nuclear magnetic resonance (NMR) spectroscopy. FT-IR spectroscopy determines the esterification of estolides using 2-ethylhexyl alcohol. The estolides have iodine values of 35~90, α-ester/α-acid ratios of 0.45~0.55, and total acid number of 114~134 mg KOH g^–1. Four ball wear tests show that the wear scar diameters (WSDs) of estolides as base oil significantly decreased to 0.328~0.494 mm, compared to WSDs of 0.735 and 0.810 mm of WSD for 150N and Yubase 6, respectively, as general base oil. Thus, the estolides have better wear resistance and satisfying design objectives for the engineering of a variety of lubricant base oils.

• Proceedings of the KSME Conference
• /
• 2008.11b
• /
• pp.3026-3031
• /
• 2008

In conventional closed-loop crankcase ventilation systems, the lubrication oil had to be re-circulated to the intake manifold, in the form of oil mist mixed with the blow-by gas. This blow-by gas containing the engine lubricant oil affects on the engine problems and the exhaust emissions. A high-efficient oil separator is required to minimize consumption of engine oil and reduce harmful emissions. In the conventional oil separator of CI engines, it has good oil separation performance even though separator design is simple, due to lots of the blow-by gas. As the emission regulation becomes severe, the oil separator for SI engines is also required. But in SI engines, separator design should be optimized, due to small size of oil particles and little amount of blow-by gas. In this study, oil separation performance classified by diameter of oil mist in cylinder head cover internal model which has three cyclones and two baffle plates for SI engine is calculated with CFD methodology.