• 한국정보전자통신기술학회논문지
• /
• 제12권2호
• /
• pp.113-119
• /
• 2019

우리는 선행연구로 다기능 마찰력 측정기를 개발해 왔고 본 논문에서는 적응화 평활화 방법을 적용하여 마찰력 측정기의 성능을 개선하고자 하였으며, 스크래치 테스트를 통해 시편에 대한 마찰력과 마찰면의 모니터링 기능을 심도 있게 분석하였다. 일반적으로 강판을 가공하여 사용하고자 할 때 마찰을 줄이기 위해서 윤활유를 사용하지만, 윤활유는 환경오염의 큰 원인이기 때문에 본 연구에서는 윤활강판을 사용하였다. 특히, 윤활강판의 마찰계수는 유기, 무기 등의 시편의 종류 및 코팅층의 상태에 따라 변화하기 때문에 합금화 용융아연도금강판과 같은 다양한 시편에 대한 정밀한 실험을 통해 분석하였다. 이를 토대로 적응화 평활화법을 이용하여 잡음이 제거된 정확한 마찰계수를 측정할 수 있는 측정기의 성능을 향상시킬 수 있음을 검증하였다. 그 결과로서 마찰계수 0.16에 대하여 적응화 평활화법을 이용한 경우 저감률이 0.0417%임을 보였다.

• 한국재료학회지
• /
• 제19권3호
• /
• pp.156-162
• /
• 2009

Lubricant-based nanofluids were prepared by dispersing carbon nanoparticles in gear oil. In this study, the effects of the particle size, shape and dispersity of the particles on the tribological properties of nanofluids were investigated. Dispersion experiments were conducted with a high-speed bead mill and an ultrasonic homogenizer, and the surfaces of the nanoparticles were simultaneously modified with several dispersants. The effective thermal conductivity of the nanofluids was measured by the transient hot-wire method, and the tribological behaviors of the nanofluids were also investigated with a disk-on-disk tribo-tester. The results of this study clearly showed that the combination of the nanoparticles, the deagglomeration process, the dispersant and the dispersion solvent is very important for the dispersity and tribological properties of nanofluids. Lubricant-based nanofluids showed relatively low thermal conductivity enhancement, but they were highly effective in decreasing the frictional heat that was generated. For nanofluids containing 0.1vol.% graphite particles in an oil lubricant, The friction coefficient in the boundary and fluid lubrication range was reduced to approximately 70% of the original value of pure lubricant.

• 한국기계가공학회지
• /
• 제7권4호
• /
• pp.62-67
• /
• 2008

In this research, we developed a pilot wire-drawing machine as well as wire end-pointing roller. Using these machines, we performed a pilot wire-drawing test at different coating material and lubricant when the reduction ratio is 10 %. To inversely compute the friction coefficient between the coating layer of wire and the surface of die for a specific lubricant, we carried out a series of three dimensional finite element analysis. Results show that the drawing force is varied with the coating material of wire at the same reduction ratio and lubricant. It is noted that the frictional coefficient in drawing is dependent on the coupled property of coating material and lubricant, indicating the best coating material for a given lubricant.

• 한국분말야금학회:학술대회논문집
• /
• 한국분말야금학회 1994년도 추계학술대회강연 및 발표대회 강연및 발표논문 초록집
• /
• pp.12-13
• /
• 1994

• 한국분말야금학회:학술대회논문집
• /
• 한국분말야금학회 2006년도 Extended Abstracts of 2006 POWDER METALLURGY World Congress Part 1
• /
• pp.321-322
• /
• 2006

Nano-structured ceramics, which consist of structural elements with nanometer-size crystallites, are expected to show various unusual properties. We developed the novel nano-structured ceramics which consists of $Si_3N_4$ and TiN and a self-lubricant material. The ceramics was fabricated by powder metallurgy process using mechano-chemical grinding process and short-time sintering process. Each grain size of matrix and the self-lubricant particle was under about 50 nm and a few namometer. It showed high wear resistance and low friction coefficient by controlling of microstructure.

• Tribology and Lubricants
• /
• 제19권6호
• /
• pp.365-369
• /
• 2003

This paper presents an experiment of the characteristics of lubricating oils for refrigerating and air conditioning. We investgate influences of lubricating oils and additives on friction and wear by reciprocating type and pendulum type friction testers. The result shows that polyolesters have excellent friction characteristics and poor effect of additives. In contrast, polyvinylethers gave higher coefficient of friction, low wear amount and good effect of additives. We can see good relationship between the coefficients of friction in recipricating type and pendulum type friction testers.

• Tribology and Lubricants
• /
• 제13권1호
• /
• pp.34-41
• /
• 1997

Frictional behavior of three automotive friction materials (brake pads) containing different amounts of antimony trisulfide ($Sb_2S_3$) and zirconium silicate ($ZRSiO_4$) were investigated using a front brake system. The friction materials were tested on a brake dynamometer (dyno) with gray cast iron rotors. The dynamometer(dyno) test simulated the dragging of a ehicle maintaining 70 km/h and vehicle stops from 100 km/h using 20 different combinations of initial brake temperature (IBT) and input pressure (IP). The results showed a strong influence of the relative amount of $Sb_2S_3$ and $ZrSiO_4$ in friction materials on friction characteristics. Friction stability was improved with the higher concentration of $Sb_2S_3$ in the friction material. Torque variation during drag cycle was increased with an increase of the $ZrSiO_4$ concentration in the friction material. Average friction coefficient and the wear rate of the friction material increased by using more aggressive friction materials containing more $ZrSiO_4$ and less $Sb_2S_3$. Generation of the disk thickness variation (DTV) increased when friction materials with higher concentration of $ZrSiO_4$ were used Careful examination of DTV change showed that aggressiveness of the friction material played an important role in determining torque variation.

• 소성∙가공
• /
• 제11권6호
• /
• pp.475-481
• /
• 2002

Tube hydroforming is a relatively new technology in comparison with conventional stamping process. Thus, there is no large knowledge base to assist the product and process designers, especially from the friction point of view. This paper covers the topic of friction and lubrication with regard to tube hydroforming. It presents the fact that frictional characteristic can have an effect on the formability of specific components. The presented concept describes the equipment which is required to determine the friction coefficient. Some example results of the friction and bulge test are shown.

• 한국정밀공학회지
• /
• 제17권4호
• /
• pp.29-37
• /
• 2000

At present there are many theories as to how various lubricants used in forging perform the role of reducing friction. Little work has been carried out to determine the validity of these theories for solid lubricants. This paper covers the development and preliminary results of the experiments devised to illustrate the movement of graphite at the workpiece/tool interface in the work forging temperature range. The paper describes the results obtained from upsetting of rings between two flat dies for measurement of lubricant thickness and compaction of graphite for density-pressure relationship. These allowed the lubricant to be exposed to forging conditions and by applying the principles of Male's ring test the simple generation of a value fur friction factor could also be determined. The experiments have been undertaken to examine the behavior of lubricant for shot blasted surface and change of surface roughness. A simple computer model of the interface has been constructed characterizing the graphite layer in an attempt to simulate the boundary mechanics.

• 소성∙가공
• /
• 제22권7호
• /
• pp.394-400
• /
• 2013

Microforming is a very efficient and economical technology to fabricate very small metallic parts in various applications. In order to extend the use of this forming technology for the production of microparts, the size effect, which occurs with the reduction of part size and affects the forming process significantly, must be thoroughly investigated. In this study, the tribological size effect in microforming was studied using modeling and scaled ring compression experiments. A micro-scale friction approach based on the slip-line field theory and lubricant pocket model was used to understand the friction mechanism and explain the tribological size effect. Ring compression tests were performed to analyze the interfacial friction condition from the deformation characteristics of the ring specimens. In addition, finite element analysis results were utilized to quantitatively determine the size-dependent frictional behavior of materials in various process conditions. By comparing theoretical results and experimental measurements for different size factors, the accuracy and reliability of the model were verified.