• Journal of Power System Engineering
• /
• v.9 no.2
• /
• pp.40-44
• /
• 2005

A great deal of exhaust gas inside a combustion room goes out through exhaust pipe but residual gas, is called "Blowby gas", enters the crankcase through a small gap between the piston and the cylinder wall. Here, if the crankcase isn't vented, this causes many bad effects such as lubricant oil contamination, corrosion by that and crankcase explosion by rising pressure. So, most automobiles are constituted with a PCV (Positive Crankcase Ventilation) system to prevent previous problems. PCV valve is the most important part in this ventilation system. When companies are manufacturing new engines, engineers are designing it depending on their experiments than theoretical knowledge. Mush efforts and times are needed for new development. This study will show quantitative results to increase the possibilities of reduction of developing time.

• Tribology and Lubricants
• /
• v.19 no.4
• /
• pp.195-202
• /
• 2003

Many computational researches have been performed about EHL film thickness in the contact between cam and follower in the engine valve train system. However, those computations do not explain the characteristics of dynamic film thickness which means squeeze film effect. Without the consideration of transient term in the Reynold's equation, the predicted film thickness from steady state condition has large difference from the actual film thickness. In this study, we have investigated the kinematic and dynamic simulations of rocker-arm valve train system. From the dynamic simulation, the applied load and the entraining velocity of the lubricant between cam and follower are obtained and with these values the dynamic film thickness is computed by Newton-Raphson method and compared with the steady state film thickness.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.7 no.1
• /
• pp.119-119
• /
• 1998

The purpose of this study is to investigate the effects of operation factors of a typical main spindle system on the efficiency of machine tool. In this study. both static and dynamic analysis of typical main spindle system of the machine tool are performed using a finite element method. These finite element results are then used to predict the bearing stiffness. the amount of heat generation as well as the bearing life in the spindle system. Effects of material type of ball-bearing. bearing-lubricant type and main spindle bearing preload are examined.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2002.10b
• /
• pp.309-310
• /
• 2002

A minimal quantity lubrication (MQL) machining is able to achieve both functions of cooling and lubrication with an extremely low quantity of a cutting fluid and a large amount of air blow. Using a biodegradable ester oil, turning tests were carried out to evaluate the effectiveness of the MQL system. It was found that the performance of MQL cutting was equivalent to, or better than, that of conventional cutting, because the MQL system tends to prevent the heat damage of the tool tip and, if an effective lubricant such as a particular polyol ester is applied to the system, it can avoid the extensive transfer of workpiece materials on to the tool surface.

• Journal of Applied Reliability
• /
• v.9 no.1
• /
• pp.29-35
• /
• 2009

Due to the excellent durability of Timing Chain, it has been widely used for vehicle engine system. Unlike the timing belt, since the timing chain is operated with the metallic sprocket, the lubrication system is absolutely needed to get this system start. As frequently met at the field, the lubricant has a strong tendency to leak out from the engine due to its severe operating environment. In this paper, results of investigation for thermal movement of aluminum chain cover were described to maximize the sealing ability which is desperately needed at the development stage of engine. Based on these results, some ideas for reproducing the leakage phenomenon and solving methods were proposed.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 1990.06a
• /
• pp.7-31
• /
• 1990

Tribologicsl diagnostics as the ensemble of means and methods of continuous monitoring of the state of friction characteristics of moving junctions is playing an ever important part in the development of friction, lubrication, and wear theory end practice. The scheme presenting the main areas of tribological diagnostics is given in Fig. I. This growing part of TD is determined by the general tendency of modern technology, expressed in an attempt to organically combine the functions of measuring, evaluating,and predicting the parameters and characteristics of the processee taking place in the operating device. The logical result of this integration in future is the closed system correcting its operation in accordance with sn established program. Unfortunately, tribotechnicsl devices are still very far from such an ideal system at the present time. While in the friction assemblies with hydrodynamic lubrication it is possible in the first approximation to realize feed-backs in the lubricant circulation system with the aid of monitoring of the pressure, temperature and filtration, in the systems operating without lubrication and with boundary lubricetion even the process of selection of the diagnostic parameters has not been completed.

• Journal of Power System Engineering
• /
• v.15 no.6
• /
• pp.41-46
• /
• 2011

Refrigerant oil reduces friction between piston and cylinder of compressor and is normally hard to mix or dissolve in refrigerant. Oil separator deprives refrigerating oil from mixed solution of refrigerant and refrigerant oil. Sometimes much machine oil is carried into an evaporator and is applied to surface of the evaporator, and then disturbs heat transfer through it. Well-made oil separator helps refrigerating system stable and evaporator sustain full capacity. In this paper, new oil separate with different way to structure is suggested and tested. As result the new separates is 13% higher at 0C with 10% mixture and 6% higher at 0C with 20% mixture.

• Tribology and Lubricants
• /
• v.18 no.2
• /
• pp.105-108
• /
• 2002

Specially designed grooved journal bearings are installed in the main coolant pump for SMART (System-integrated Modular Advanced ReacTor) to support radial load on the rotating shaft. The canned motor type main coolant pumps are arranged vertically on the reactor vessel and filled with circulating primary coolant which is pure water. The main coolant pump bearings are lubricated with this coolant without any other external lubricant supply. Because lubricating condition is too severe for this bearing to generate proper hydrodynamic film, investigation of lubrication characteristics of the journal bearing is important to satisfy life constraint of whole pump system, and the results will be applied to the analysis of dynamic characteristics of the shaft system. The bearing is made of silicon graphite which has self$.$lubricating effect. A lubrication analysis method is proposed for this vertically grooved journal bearing in the main coolant pump of SMART, and lubricational characteristics of the bearings are examined in this paper.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.7 no.8
• /
• pp.7-16
• /
• 1999

To maintain thereasonable temperature in the engines is very important to keep the steady combustion state of engine and to prevent increasing of oil consumption , deteriorating of lubricant, shortening of the life time of engine and decreasing of material strength. The method of energy balance for divided elements of radiator and engine-oil cooler is considered to analyse the performance of radiator and engine-oil cooler. The data obtained by engine test and vehicle cooling tunnel test are applied to program for calculation of radiator outlet temperature. As a result, data obtained by numerical analysis agree well with those by experiments. And thus, it is concluded that this simulation program is available in developing the cooling system for a new car.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2000.11a
• /
• pp.397-405
• /
• 2000

Many computational researches have been performed about EHL film thickness in the contact between cam and follower. However, those computations do not explain the characteristics of dynamic film thickness which means squeeze film effect. Without the consideration of transient term in the Reynold's equation, the predicted film thickness has large difference from the actual film thickness. In this study, we have investigated the kinematic and dynamic simulations of rocker-arm valve train system. From the simulation, the applied load and the entraining velocity of the lubricant between cam and follower are obtained and with these values the dynamic film thickness is computed by Newton-Raphson method and compared with the steady state film thickness.