• Journal of Energy Engineering
• /
• v.11 no.3
• /
• pp.247-253
• /
• 2002

Natural manganese ore was selected as main active component for a non-zinc desulfurization sorbent used in the gas clean-up process of the integrated gasification combined cycle (IGCC) because of excellent H$_2$S removal efficiency and economical aspect . In this study, the regeneration characteristics of sorbent after desulfurization reaction were determined in a thermobalance reactor and a fixed bed reactor in the temperature range of 350~55$0^{\circ}C$. The mixed gases of oxygen and nitrogen are used as the regeneration reaction gases for manganese sorbent. According to Mn-S-O phase diagram, the manganese sorbent has a low regeneration efficiency in medium temperature due to formation of MnSO$_4$ and the regeneration temperature must be over 85$0^{\circ}C$. To improve that problem, ammonia and steam was added in regeneration mixed gases. Effect of new regeneration method was determined by XRD and difference of desulfurization through multicycle tests.

• Journal of the Korean Society for Geothermal and Hydrothermal Energy
• /
• v.2 no.1
• /
• pp.1-7
• /
• 2006

This paper was studied for optimum design of the used vaporizer at a satellite station. Generally, the cold air is created by temperature drop on the vaporizer surface. In addition, the frost creates ice deposit layer, therefore, heat transfer on vaporizer decreases into the adiabatic condition. By this reason, recent vaporizer system is installed as parallel type, and it takes three times of vaporizer capacity. But this vaporizer system requires much installation costs and restricted by some space. It is very important to solve this problem. This study paper is regarding $LN_2$ vaporizer where the utilization increases recently. There are three variable conditions which are used in this study research. First, fin lengths of 4000mm, 6000mm, 8000mm and 0, 4, 8 fin types were applied rut each vaporizer. Second, we applied four season condition which consist of humidity, temperature and air velocity to the experimental environment. Finally, pressure was applied to get flow rate during experiment. This paper objective is to propose vaporizer type and length data for best performance of vaporizer through experiment.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.20 no.4
• /
• pp.491-496
• /
• 2017

The hydrogen($H_2$) is promising energy carrier of renewable energy in the microgrid system such as small village and military base due to its high energy density, pure emission and convenient transportation. $H_2$ can be generated by photocatalytic water splitting, gasification of biomass and water electrolysis driven by solar cell or wind turbine. Solid oxide electrolysis cells(SOECs) are the most efficient way to mass production due to high operating temperature improving the electrode kinetics and reducing the electrolyte resistance. The SOECs are consist of nickel-yttria stabilized zirconia(NiO-YSZ) fuel electrode / YSZ electrolyte / lanthanum strontium manganite-YSZ(LSM-YSZ) air electrode due to similarity to Solid Oxide Fuel Cells(SOFCs). The Ni-YSZ most widely used fuel electrode shows several problems at SOEC mode such as degradation of the fuel electrode because of Ni particle's redox reaction and agglomeration. Therefore Ni-YSZ need to be replaced to an alternative fuel electrode material. In this study, We studied on the Double perovskite $PrBrMnO_{5+{\delta}}$(PBMO) due to its high electric conductivity, catalytic activity and electrochemical stability. PBMO was impregnated into the scaffold electrolyte $La_{0.8}Sr_{0.2}Ga_{0.85}Mg_{0.15}O_{3-{\delta}}$(LSGM) to be synthesized at low temperature for avoiding secondary phase generated when it exposed to high temperature. The Half cell test was conducted at SOECs and SOFCs modes.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.35 no.11
• /
• pp.1177-1184
• /
• 2011

Gas-to-Solid (GTS) technology is composed of three stages: hydrate production, transportation, and regasification. For efficient operation of regasification plants, it is crucial to predict the temperature and flow rate of hot water necessary to dissociate the hydrate pellets. Dissociated gas escaping from the pellet surface, when in contact with hot water, will alter the flow field and consequently alter the heat transfer rate. Methane hydrate pellet dissociation characteristics in low- to moderatetemperature water were investigated by taking images of the changes in the hydrate pellets' shapes in a pressurized reactor and measuring the total time required for complete melting of the pellets. The effects of water temperature, hydrate conversion rate, and flow speed on the dissociation completion time were also investigated. Bubbling gas released from the pellet surface induced a secondary flow that enhanced the heat transfer rate and thus decreased the dissociation time. It was also found that a considerable flow rate was needed to significantly decrease the dissociation time.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.41 no.8
• /
• pp.639-648
• /
• 2013

This paper describes on the NOx/CO emission characteristics, temperature characteristics and flame structures when firing coal derived synthetic gas especially for gases of Buggenum and Taean IGCC. These combustion characteristics were observed by conducting ambient-pressure elevated-temperature combustion tests in GE7EA model combustor when varying heat input and nitrogen dilution ratio. Nitrogen addition caused decrement in adiabatic flame temperature, thus resulting in the NOx reduction. At low heat input condition, nitrogen dilution raised the CO emission dramatically due to incomplete combustion. These NOx reduction and CO arising phenomena were observed at certain flame temperature of $1500^{\circ}C$ and $1250^{\circ}C$, respectively. As increasing nitrogen dilution, adiabatic flame temperature and combustor liner temperature were decreased and singular points were detected due to change in flame structure such as flame lifting. From the results, the effect of nitrogen dilution on the NOx/CO and flame structure was examined, and the test data will be utilized as a reference to achieve optimal operating condition of the Taean IGCC demonstration plant.

• Applied Chemistry for Engineering
• /
• v.31 no.6
• /
• pp.688-696
• /
• 2020

Petroleum coke (petcoke) is widely used, next to coal, as a gasification feedstock. In gasification processes, the viscosity of the ash and the formation of crystalline phases must be understood to ensure the continuous removal of slag. This study investigates the effect of CaO and V2O3 on petcoke slag viscosity. The viscosity of the molten slag was measured in the temperature range of 1100~1600 ℃ while varying the concentration of each component. The crystalline phases formed in a cooled slag were examined. The most slag samples tested in this study exhibited crystalline slag behavior. The increased CaO concentration resulted in a lower viscosity and a lower Tcv. The viscosity behavior changed from the glassy to crystalline slag and also showed a higher Tcv as the concentration of V2O3 increases. Most slag samples showed different crystalline phases from top to bottom. Anorthites and Ca-V phases were observed in the top and middle section, while the bottom section mainly showed V2O3 and anorthite. The vanadium in the ash forms Ca-V and V-Fe phases and also remains in molten slag. A low melting Ca-V phase can contribute to lowering the viscosity.

• Journal of Energy Engineering
• /
• v.5 no.1
• /
• pp.8-18
• /
• 1996

As a part of comprehensive IGCC process simulation, the thermal performance analysis was performed for coal gas firing combined power plant. The combined cycle analyzed consisted of il Texaco gasifier and a low temperature gas cleanup system for the gasification block and a GE 7FA gas turbine, a HRSG and steam turbine for the power block. A steady state simulator called ASPEN(Advanced System for Process Engineering) code was used to simulate IGCC processes. Composed IGCC configuration included air integration between ASU and gas turbine and steam integration between gasifier, gas clean up and steam turbine. The results showed 20% increase in terms of gas turbine power output(MWe) comparing with natural gas case based on same heat input. The results were compared with other study results which Bechtel Canada Inc. performed for Nova Scotia power plant in 1991 and the consistency was identified within two studies. As a result, the analysing method used in this study is verified as a sound tool for commercial IGCC process evaluation.

• Journal of the Korea Organic Resources Recycling Association
• /
• v.29 no.4
• /
• pp.47-54
• /
• 2021

In this study, the performance of a honeycomb-type hydrogen oxidation catalyst to remove hydrogen in a hydrogen economy society to secure leaking hydrogen. The Pd/TiO₂ catalyst was prepared based on a liquid phase reduction method that is not exposed to a heat source, and it was showed through H₂-chemisorption analysis that it existed as very small active particles of 2~4 nm. In addition, it was found that the metal dispersion decreased and the active particle size increased as the reduction reaction temperature increased. It was meant that the active metal particle size and the hydrogen oxidation performance were in a proportional correlation, so that it was consistent with the hydrogen oxidation performance reduction result. The prepared catalyst was coated on a support in the form of a honeycomb so that it could be applied to the hydrogen industrial process. When 20 wt% or more of the AS-40 binder was coated, oxidation performance of 90% or more was observed under low-concentration hydrogen conditions. It was showed through SEM analysis that long-term catalytic activity can be expected by enhancing the adhesion strength of the catalyst and preventing catalyst desorption. It is a basic research that can secure safety in a hydrogen society such as gasification, organic resource, and it can be utilized as a system that can respond to unexpected safety accidents in the future.

• Journal of Power System Engineering
• /
• v.11 no.2
• /
• pp.5-11
• /
• 2007

액화천연가스(LNG : Liquified Natural Gas)는 연료로 사용하기 위하여 기화하는 과정을 거치게 되는데 기화하는 방식에는 해수에 의한 기화와 공기에 의한 기화의 두 가지 방식으로 나뉘게 된다. 해수에 의한 기화는 LNG 인수기지에서 대량의 LNG를 NG로 기화하기 위하여 사용하며, 공기에 의한 기화는 LNG 위성기지에서 사용처에 적합한 온도를 얻기 위해서 일반적으로 많이 사용하고 있는 공기식 기화기를 이용하여 기화를 하는 방식을 취하고 있다. LNG가 NG로 기화하는 과정에서 1kg당 200kcal의 냉열을 외부로 방출하고 있으며, 이러한 냉열의 방출로 인하여 공기식 기화기의 표면에 결빙현상을 발생시킨다. 또한 현재 사용하고 있는 기화기는 $2{\sim}3$개의 기화기를 연결하여 사용하고 있어 그 비용의 손실이 크다고 할 수 있다. 그리하여 본 연구는 최근 사용빈도가 증가하고 있는 공기식 기화기에 관한 것으로 작동유체는 실제 LNG와 특성이 비슷한 초저온 액화가스인 $LN_2$를 사용하였다. 이번 연구에 사용된 변수는 다음과 같다. 첫째, 각각의 기화기의 길이를 4000mm, 6000mm, 8000mm으로 하였고 핀의 type을 finless, 4fin, 8fin으로 하여 적용하였다. 두 번째는 봄, 여름, 가을, 겨울철에 따른 기화기의 성능을 알고자 각각의 계절별 온도와 습도를 적용하였다. 마지막으로 계절별 풍속과 실험을 하는 시간 동안의 유량을 알고자 압력을 1 bar로 적용하였다. 그리하여 이번 연구의 목적으로는 각각의 변수를 통하여 실험을 진행 한 후 vaporizer type과 길이에 대한 최적의 성능을 가지는 기화기에 대한 자료를 제시하고자 한다.기성분은 균주에 따른 약간의 차이가 있었으나 경향은 비슷하게 나타났다. 이상의 결과 알코올 발효 균주에 따른 참다래 와인의 이화학적 품질특성에는 큰 차이가 없었으나 고급알코올함량을 비교하였을 때 Sacch. cerevisiae Wine 3이 와인제조에 가장 적합한 것으로 평가되었다.장 낮은 값을 나타내었으며, 홍국의 함유량이 증가할수록 유의적으로 증가하였다. b값은 CSB가 가장 낮은 값을 나타내었으며, 홍국의 함유량이 증가할수록 유의적으로 증가하였다. 물성측정 결과 경도와 응집성은 각 시료들 간의 유의적인 차이가 나타나지 않았다. 탄력성과 부서짐성은 CSB가 가장 낮았으며, 홍국의 함유량이 증가할수록 증가하였다. 점착성은 SDB1이 가장 낮았으며, 홍국의 함유량이 증가할수록 증가하였다. 관능검사 결과 기공의 균일성은 SDB1이 가장 균일한 것으로 나타났으며, 색은 홍국의 함유량이 증가할수록 높게 나타났다. 경도, 탄력성, 단맛 및 신맛 등은 홍국 함유량이 증가할수록 증가하는 것으로 나타났다. 이취는 SDB1이 가장 적게 나는 것으로 나타났으며, 전반적인 기호도는 SDB1이 가장 높았다. 따라서 홍국을 10% 첨가한 sourdough starter를 3일 동안 발효한 후 반죽에 첨가하여 sourdough bread를 제조할 때 품질이 가장 우수한 제품을 얻을 수 있었다.생수와 여러 물질의 혼합용액의 온도가 장에 끼치는 자극에 차이가 있지 않나 추측되며 이에 관한 추후 연구가 요망된다. 총대장통과시간의 단축은 결장 분절 모두에서 줄어들어 나타났으나 좌측결장 통과시간의 감소 및 이로 인한 이 부위의 통과시간 비율의 저하가 가장 주요하였다. 이러한 결과는 차가운 생수 섭취가 주로 결장 근위부를 자극하는 효과를 발휘하는 것이 아닌가

• Clean Technology
• /
• v.13 no.4
• /
• pp.266-273
• /
• 2007

The adsorption properties of the activated carbon-based adsorbents were studied to remove COS emitted from $SO_2$ catalytic reduction process on the integrated gasification combined cycle (IGCC) system in this work. Transition metal supported catalysts and mixed metal oxide catalysts were used for the $SO_2$ catalytic reduction. The mechanism of COS produced from the $SO_2$ reduction and the COS concentration s according to the reaction temperature were investigated. In this study, an activated carbon and a modified activated carbon doped with KOH were used to remove the very low concentration of COS effectively. The adsorption rate and the breakthrough time of COS were measured by a thermo gravity analyzer (TGA, Cahn Balance) and a fixed bed flow reactor equipped with GC-pulsed flammable photometric detector (PFPD), respectively. It was confirmed that the COS breakthrough time of the activated carbon doped with KOH was longer than that of an activated carbon. In conclusion, the modified-activated carbon having a high surface area showed a high adsorption rate of COS produced from the $SO_2$ reduction.