• 한국신재생에너지학회:학술대회논문집
• /
• 2009.11a
• /
• pp.382-382
• /
• 2009

염료감응형 태양전지의 구성체 중 전극으로 연구 되어 지고 있는 $TiO_2$는 기존에 대량 생산이 가능한 spin coating법, screen printing법, spray법의 연구가 이루어져 왔으나 고 효율 태양전지에 쓰이는 전극 시스템에 비해 고 분산성을 지닌 $TiO_2$페이스트를 제조 하는데 어려움이 있다. 그리고 플렉시블 디스플레이 소자의 응용을 위해서는 소자 공정 온도인 $250^{\circ}C$ 이하의 공정 온도가 요구 되어 지므로 고온공정인 CVD법은 이에 적합하지 않다. 이에 본 연구는 진공 증착 방법인 광원자층증착법을 이용하여 $150^{\circ}C$이하의 저온공정온도에서도 적용이 가능한 $TiO_2$ 박막을 185nm의 UV light를 조사하여 glass 기판위에 제조 하고 그에 따른 박막의 물성 분석을 하였다. Mo source로는 titanium tetraisopropoxide(TTIP)와 reactant gas 로는 $H_2O$를 사용하였으며 불활성 기체인 Ar 가스는 purge 가스로 각각 사용하였다. $100^{\circ}C{\sim}250^{\circ}C$ 공정온도를 변수로 $TiO_2$ 박막을 제조 하였으며 제조된 $TiO_2$ 박막의 물성 분석을 위해 FESEM, TEM을 이용하여 표면 및 두께를 분석하였다. 또한 $100^{\circ}C$ 400 cycles에서 약 12nm 막 두께를 관찰 할 수 있었으며 그 결과 박막의 성장률이 $0.3{\AA}$/cycle 임을 확인 할 수 있었다. 그리고 UV-VIS을 이용하여 박막의 좌외선에 대한 흡수도 및 투과도 분석을 하였다. 또한 XPS 성분 분석을 통하여 $100^{\circ}C$의 저온 공정에서 형성된 박막이 $TiO_2$임을 확인 하였다. 이러한 결과에서 185nm의 UV light에 의한 광원자층 증착법으로 $100^{\circ}C$의 저온에서도 $TiO_2$ 박막이 증착 되는 것을 확인 할 수 있었다.

• Journal of Microbiology and Biotechnology
• /
• v.20 no.10
• /
• pp.1440-1445
• /
• 2010

Rhodococcus sp. JDC-11, capable of utilizing di-n-butyl phthalate (DBP) as the sole source of carbon and energy, was isolated from sewage sludge and confirmed mainly based on 16S rRNA gene sequence analysis. The optimum pH, temperature, and agitation rate for DBP degradation by Rhodococcus sp. JDC-11 were 8.0, $30^{\circ}C$, and 175 rpm, respectively. In addition, low concentrations of glucose were found to inhibit the degradation of DBP, whereas high concentrations of glucose increased its degradation. Meanwhile, a substrate utilization test showed that JDC-11 was also able to utilize other phthalates. The major metabolites of DBP degradation were identified as monobutyl phthalate and phthalic acid by gas chromatography-mass spectrometry, allowing speculation on the tentative metabolic pathway of DBP degradation by Rhodococcus sp. JDC-11. Using a set of new degenerate primers, a partial sequence of the 3,4-phthalate dioxygenase gene was obtained from JDC-11. Moreover, a sequence analysis revealed that the phthalate dioxygenase gene of JDC-11 was highly homologous to the large subunit of the phthalate dioxygenase from Rhodococcus coprophilus strain G9.

• Korean Chemical Engineering Research
• /
• v.61 no.3
• /
• pp.378-387
• /
• 2023

Petrochemical is an energy consuming industry that consumes about 30% of total industrial energy consumption and is a representative carbon dioxide (CO₂) emission source. Among them, the Naphtha Cracking Center (NCC), which produces ethylene, propylene, propane and mixed C4, consumes large amounts of energy and emits significant amounts of CO₂. For this reason, an integrated techno economic- environmental impact assessment aimed at reducing energy consumption and environmental impact factors is necessary to ensure efficiency in terms of economics and environment. This study aims to analyze the efficiency of the heat exchanger network used in the existing NCC base on the pinch analysis and select an improvement plan that can reduced energy consumption. In order to reduces the utility consumption in the process, an optimal heat exchanger network considering the high-temperature and low-temperature stream was derived, and the economic evaluation was conducted by considering the trade-off between the reduction in utility consumption and the increase in heat exchanger installation cost. In addition, an environmental impact assessment was conducted on the reduced CO₂ emission in consideration of the environmental aspect, and the economic environmental impact assessment used the payback period to recover the invested funds to come up with an energy saving plan that can be applied based on the actual process. As a result of considering the economic-environmental impact assessment, when the environmental impact assessment was not considered, it was 4.29 months, 3.21 months, and 3.39 months for each case, and when considering the environmental impact assessment, it was 4.24 months, 3.17 months, and 3.35 months for each case. These results appeared equally both when the environmental impact assessment was not include and when it was include. In addition, a sensitivity analysis was conducted for each case to determine how important factors affect the payback period. As a result of the sensitivity analysis, the cost of the heat exchanger was identified as a major factor influencing the overall cost.

• Journal of the Society of Cosmetic Scientists of Korea
• /
• v.41 no.1
• /
• pp.27-34
• /
• 2015

Many applications of nanoparticles have been developed since 1970s. Surface plasmon resonance (SPR) effect can be generated at the surface of nanoparticles by illumination. SPR is the resonant oscillation of conduction electrons at the surface material stimulated by incident light. The collisions between excited electrons and metal atoms can cause the production of thermal energy (photothermal effect). Here, we presented the development of thermo-cosmetics using photothermal effect of gold nanoparticles. Gold nanoparticles (GNPs) were chosen for it's low toxicity. We also and investigated the cell biocompatibility and heating effectiveness for photothermal effect of GNPs. Synthesized GNPs were verified by UV-vis spectrophotometer, where GNP has a characteristic absorbance spectrum. Concentration of GNP was measured by atomic absorption analyzer. The cytotoxicity was confirmed by MTT assay and double staining assay. Photothermal effect of GNP was demonstrated by the thermal increasing properties depending on GNP concentration, which was taken by an IR-thermal camera with a xenon lamp as the light source. If the thermal effect of GNP is applied for thermo-cosmetics, it can supply heat to skin by converting solar energy into thermal energy. Thus, cosmetics containing GNPs can provide benefits to people in the cold region or winter season for maintaining skin temperature, which lead to a positive effect on skin health.

• Korean Journal of Materials Research
• /
• v.13 no.6
• /
• pp.347-351
• /
• 2003

II-Ⅵ ZnO compound semiconductor thin films were grown on $\alpha$-Al$_2$O$_3$(0001) single crystal substrate by radical beam assisted molecular beam epitaxy and the optical properties were investigated. Zn(6N) was evaporated using Knudsen cell and O radical was assisted at the partial pressure of 1$\times$10$^{4}$ Torr and radical beam source of 250-450 W RF power. In $\theta$-2$\theta$ x-ray diffraction analysis, ZnO thin film with 500 nm thickness showed only ZnO(0002)and ZnO(0004) peaks is believed to be well grown along c-axis orientation. Photoluminescence (PL) measurement using He-Cd ($\lambda$=325 nm) laser is obtained in the temperature range of 9 K-300 K. At 9 K and 300 K, only near band edge (NBE) is observed and the FWHM's of PL peak of the ZnO deposited at 450 RF power are 45 meV and 145 meV respectively. From no observation of any weak deep level peak even at room temperature PL, the ZnO grains are regarded to contain very low defect density and impurity to cause the deep-level defects. The peak position of free exciton showed slightly red-shift as temperature was increased, and from this result the binding energy of free exciton can be experimentally determined as much as $58\pm$0.5 meV, which is very closed to that of ZnO bulk. By van der Pauw 4-point probe measurement, the grown ZnO is proved to be n-type with the electron concentration($n_{e}$ ) $1.69$\times$10^{18}$$cm^3$, mobility($\mu$) $-12.3\textrm{cm}^2$/Vㆍs, and resistivity($\rho$) 0.30 $\Omega$$\cdot$cm.

• Journal of Biosystems Engineering
• /
• v.2 no.2
• /
• pp.37-45
• /
• 1977

Solar energy is a potential source of power that offers much promise being used for low-temperature applications like drying farm crops, space heating, and water heating for domestic uses. Already much of it are being used for those purpose in foreign countries. However, very little research has been done to determine the possibility of using the solar energy in Korea. This study was conducted to develop the general prediction equation of the total radiation on a horizontal surface in Daejeon area based on 5 years 91972, Jun.1-1976. Dec.31) meteorological data (bright sunshine hours, average total horizontal radiation), and to obtain experimentally the thermal efficiency of solar air and water collectors, which will be used as a basic data of designing flat-plate solar collector system.In addition to the thermal efficiency of the collectorsthe relationship among those factors affecting it such as weather condition, orientation factor, and tilted angle of collector was analyzed. The results of this study were as follows. 1. The general predicted equation of the total radiation on a horizontal surface in Daejeon area based on bright sunshine hours was developed as $H_{av} =(1.546\frac{n}{N}-0.582)H_o$. Predicting the total radiation on a horizontal surface by the above equation was thought to be possible because to values of 0.882 was smaller than any t values at above 0.05 level on the basis of two tailed test of the difference between the calculated and the recorded values. 2.It was observed that optimum tilt angle of the collector in the summer and the autumn drying season was 13 degrees and 51 degrees respectively, these values could be obtained by adding or substracting approximately 25 degrees from the latitude of this area $(36.3^{\circ}N)$ .The relationship between orientation factor and declination of sun at suitable tilt angle of 33 degrees $(s=0.9\O)$ was shown at Fig.4. 3.The thermal efficiency of solar wdter collector was shown 13.4-51. 6% on Aug. 15 (the minimum radiation recorded) and 43.8 ~537% Aug.20 (the maximum radiation recorded), and 13.8~ 46.6 and 44.3~ 49.7 were shown on each corresponding day. 4.The thermal efficiency of the collectors according to the weather condition was shown a big difference of about 10% between the day of the maximum radiation recorded and the minimum, but the differen of efficiency between the air and the water collector was at most 2 ~ 3%. 5. Even if the efficiency of the solar water collector was a little higher than the solar air collector, for drying farm products, the solar air collector was thought to be more effective because the air heated by collector could be directly used for drying them.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.43 no.5
• /
• pp.555-566
• /
• 2023

In this study, a composite phase change material (CPCM) produced using the SOL-GEL technique was developed as a thermal energy storage medium for low-temperature applications. Tetradecane and activated carbon (AC) were used as the core and supporting materials, respectively. The tetradecane phase change material (PCM) was impregnated into the porous structure of AC using the vacuum impregnation method, and a thin layer of silica gel was coated on the prepared composite using the SOL-GEL process, where tetraethyl orthosilicate (TEOS) was used as the silica source. The thermal performance of the CPCM was analysed using differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA). DSC results showed that the pure tetradecane PCM had melting and freezing temperatures of 6.4℃ and 1.3℃ and corresponding enthalpies 226 J/g and 223.8 J/g, respectively. The CPCM exhibited enthalpy of 32.98 J/g and 27.7 J/g during the melting and freezing processes at 7.1℃ and 2.4℃, respectively. TGA test results revealed that the AC is thermally stable up to 500℃, which is much higher than the decomposition temperature of the pure tetradecane, which is around 120℃. Moreover, in the case of AC-PCM and CPCM thermal degradation started at 80℃ and 100℃, respectively. The chemical stability of the CPCM was studied using Fourier-transform infrared (FT-IR) spectroscopy, and the results confirmed that the developed composite is chemically stable. Finally, the surface morphology of the AC and CPCM was analysed using scanning electron microscopy (SEM), which confirmed the presence of a thin layer of silica gel on the AC surface after the SOL-GEL process.

• 한국신재생에너지학회:학술대회논문집
• /
• 2005.06a
• /
• pp.663-666
• /
• 2005

Gas hydrates are ice-like compounds that form at the low temperature and high pressure conditions common in shallow marine sediments at water depths greater than 300-500 m when concentrations of methane and other hydrocarbon gases exceed saturation. Estimates of the total mass of methane carbon that resides in this reservoir vary widely. While there is general agreement that gas hydrate is a significant component of the global near-surface carbon budget, there is considerable controversy about whether it has the potential to be a major source of fossil fuel in the future and whether periods of global climate change in the past can be attributed to destabilization of this reservoir. Also essentially unknown is the interaction between gas hydrate and the subsurface biosphere. ODP Leg 204 was designed to address these questions by determining the distribution, amount and rate of formation of gas hydrate within an accretionary ridge and adjacent basin and the sources of gas for forming hydrate. Additional objectives included identification of geologic proxies for past gas hydrate occurrence and calibration of remote sensing techniques to quantify the in situ amount of gas hydrate that can be used to improve estimates where no boreholes exist. Leg 204 also provided an opportunity to test several new techniques for sampling, preserving and measuring gas hydrates. During ODP Leg 204, nine sites were drilled and cored on southern Hydrate Ridge, a topographic high in the accretionary complex of the Cascadia subduction zone, located approximately 80km west of Newport, Oregon. Previous studies of southern Hydrate Ridge had documented the presence of seafloor gas vents, outcrops of massive gas hydrate, and a pinnacle' of authigenic carbonate near the summit. Deep-towed sidescan data show an approximately $300\times500m$ area of relatively high acoustic backscatter that indicates the extent of seafloor venting. Elsewhere on southern Hydrate Ridge, the seafloor is covered with low reflectivity sediment, but the presence of a regional bottom-simulating seismic reflection (BSR) suggests that gas hydrate is widespread. The sites that were drilled and cored during ODP Leg 204 can be grouped into three end-member environments basedon the seismic data. Sites 1244 through 1247 characterize the flanks of southern Hydrate Ridge. Sites 1248-1250 characterize the summit in the region of active seafloor venting. Sites 1251 and 1252 characterize the slope basin east of Hydrate Ridge, which is a region of rapid sedimentation, in contrast to the erosional environment of Hydrate Ridge. Site 1252 was located on the flank of a secondary anticline and is the only site where no BSR is observed.

• Journal of the Korean Society for Marine Environment & Energy
• /
• v.18 no.3
• /
• pp.189-206
• /
• 2015

The present study was conducted to investigate the oceanic characteristics of the northern East China Sea through identification of long-term variation patterns of oceanic environment factors, for the objective of gaining understanding of oceanic environment characteristics of the northern waters of East China Sea, which closely influence the oceanic environments of waters nearby South Korea. The study methodology included the use of oceanographic data (water temperature, salinity, dissolved oxygen, nutrients, and chlorophyll-a) on the northern East China Sea from the Korea Oceanographic Data Center (KODC), collected by season for 20 years between 1995 and 2014. Moreover, for the study on the distribution of nutrients, chlorophyll-a. The main water masses that affected the northern East China Sea during the study period were classified as Changjiang diluted water (CDW), Tiawan current warm water (TCWW), Yellow Sea cold water (YSCW), and Kuroshio source water (KW). The forces of CDW and TCWW that forms on the surface and sub-surface layers had weakened for 20 years and the force of KW that forms on the intermediate layer showed a distinctively decreasing trend. However, YSCW showed a trend of expanding its force. Phosphate and silicate exhibited a decreasing tendency and phosphate showed a pattern of being depleted on the surface layer after 2009. It is determined that one of the reasons for this is the concentration of nutrients introduced through CDW and TCWW being too low. The concentration of chlorophyll-a exhibited an increasing tendency during the study period, the reasons for which are determined to be the influences of increase in water temperature, supply of nutrients via YSCW, and increases in light transmission from decrease in suspended solid due to the construction of the Three Gorges Dam.

• Korean Journal of Microbiology
• /
• v.41 no.3
• /
• pp.201-207
• /
• 2005

A phenanthrene-degrading bacterium HS362, which is capable of using phenanthrene as a sole carbon and energy source, was isolated from oil contaminated soil. This strain is a gram negative, rod shaped organism that is most closely related to Sphingomonas paucimobilis based on biochemical tests, and belongs to the genus Sphingomonas based on fatty acids analysis. It exhibited more than $99.2{\%}$ nucleotide sequence similarity of 16S rDNA to that of Sphingomonas CF06. Thus, we named this strain as Sphingomonas sp. HS362. It degraded $98{\%}$ of phenanthrene after 10 days of incubation when phenanthrene was added at 500 ppm and $30{\%}$ even when phenanthrene was added at 3000 ppm. Sphingomonas sp. HS362 could also degrade low molecular weight PAHs(Polycyclic aromatic hydrocarbons) such as indole and naphthalene, but was unable to degrade high molecular weight PAHs such as pyrene and fluoranthene. The optimum temperature and pH for phenanthrene degradation were $30^{\circ}C$ and $4{\~}8$, respectively. Sphingomonas sp. HS362 could degrade phenanthrene effectively in the concentration range of NaCl of up to $1{\%}$. Its phenanhrene degrading ability was enhanced by preculture, suggesting the possibility of induction of phenanthrene degrading enzymes. Starch and surfactants such as SDS, Tween 85, and Triton X-100 were also able to enhance phenanthrene degradation by Sphingomonas sp. HS362. It carries five plasmids and one of them, plasmid p4, is considered to be involved in the degradation of phenanthrene according to the plasmid curing experiment by growing at $42^{\circ}C$.